GRCGRG技术规范2017更新版 - 图文

广州孚姆新材料科技股份有限公司 FORM New Materials Tech Co., Ltd sn：FM李军20160720

广州孚姆新材料科技股份有限公司GRC/GRG /FRP/TCP技术规范

（2014更新版）

1

广州孚姆新材料科技股份有限公司 FORM New Materials Tech Co., Ltd sn：FM李军20160720

目录

Section 1：GRC Section 2：GRG Section 3：Section 4：Section 5：

FRP TCP

General Painting and Coating Specifications

2

广州孚姆新材料科技股份有限公司 FORM New Materials Tech Co., Ltd sn：FM李军20160720

SECTION1：GLASS FIBER REINFORCED

CONCRETE(GFRC/GRC) 玻璃纤维加强水泥(GFRC/GRC)

PART 1. GENERAL 第1部分. 简介

1.01 RELATED DOCUMENTS 1.01 相关文件

A. Drawings, Conditions of the Contract and Division 1 Specifications sections, apply to work of this section.

A. 图纸、合同条款及第一部分说明章节适用于本章内容； 1.02 SUMMARY 1.02 概要

A. Section Includes: Glass Fiber Reinforced Concrete (GFRC) part fabrication and installation as scheduled at the end of this section and as shown on the architectural drawings.

A. 章节内容包括：如本章结尾提到及建筑图纸所示，玻璃纤维加强水泥(以下简称为GFRC或GRC)制造及安装；

1.03 REFERENCE STANDARDS 1.03 参考标准

A. ASTM C947: Test Method for Flexural Strength A.ASTM C947- 弯曲强度测试方法

B. ASTM E-84: Test Method for Surface Burning Characteristics of Building Materials. B. ASTM E-84: 建筑材料表面燃烧特性测试方法

C. MNL-128: Range of Premix Properties Recommended to PCI. C. MNL-128: PCI标准推荐的预混料属性的范围

D. ASTM E136: Test method for Surface Burning Characteristic of Building Materials. D. ASTM E136: 建筑材料表面燃烧特性测试方法 1.04 SUBMITTALS 1.04 提交材料

3

广州孚姆新材料科技股份有限公司 FORM New Materials Tech Co., Ltd sn：FM李军20160720

A. Samples: submit six (6) each, 300mm x 300mm and (20) 50mm x 50mm samples demonstrating finish to be supplied (finish per contract).

A. 样板： 提交6件300mm x 300mm和20件50mm x 50mm的样板，该样板需展示表面效果（按合同）；

B. Shop Drawings: Submit shop drawings delineating all details required for fabrication and installation. Shop drawings to indicate the necessary blocking and attachment to the building or framing as required to support and secure the GFRC material and any material attached to GFRC. Framing details and structural support of framing is the responsibility of the GFRC manufacturer/installer, and it is to be engineered and sealed by contractor/subcontractor, and noted accordingly in the material supply contract and shop drawings.

B. 施工图：提交描述所有生产及安装细节的施工图，施工图需表明必要的安装块/框架和连接物，用于支撑和稳固GFRC材料或其他固定在GFRC上的材料；框架细节和框架结构支撑由GFRC生产方负责，由承包方/安装方进行工程设计，并在材料供应合同和施工图纸安装细节中标注清楚。

1.05 QUALITY ASSURANCE

A. All GFRC parts shall match approved samples.

A. 所有GFRC产品必须与通过的样板相符。B. All GFRC parts and additional framing required due to non-structural walls (e.g. brick or others) will be Installable according to details submitted in shop drawings. All support and framing systems must be engineered by an engineer able to place his seal for the structure and design of all GFRC panels and installation systems as he sees them acceptable and certified fit for purpose.

B. 根据提交的施工图,所有GFRC件及非结构墙后补墙（如砖或其他）必须可安装。所有支撑及结构系统必须由结构工程师设计、计算其结构、包括所有GFRC板及其安装系统。机构工程师须盖章证明结构可行可达到目的。 C. Pigments C. 色粉:

1. Coloring Admixture: ASTM C979, synthetic mineral-oxide pigments or colored water-reducing admixtures, temperature stable, nonfading, and alkali resistant.

1.着色添加剂: ASTM C979,合成氧化物矿物色粉或者着色减水添加剂,耐温度,不褪色,抗碱性。

2. Coloring Admixture: not to exceed 10 percent of cement weights.

4

广州孚姆新材料科技股份有限公司 FORM New Materials Tech Co., Ltd sn：FM李军20160720

2.着色添加剂:比重不能超过水泥重量的10%. 1.07 DELIVERY, STORAGE AND HANDLING 1.06 运输、仓储及操作

A. All materials shall be protected during fabrication, shipment, site storage and erection to prevent damage to the finished work from other trades. Store materials inside a well-ventilated area, away from uncured concrete and masonry, and protected from weather moisture, soiling, abrasion, and extreme temperatures.

A.所有材料必须在生产、运输、工地存储及安装过程加以保护，以防止其他工种损坏已完成的工作。将材料存储于通风良好的地方，远离未固化的水泥和砖石，并保护其不受天气潮湿天气、脏污、磨损、弯曲及极端天气影响。

B. Protect fabrications from damage by retaining or duplicating shipping protection in place until installation.

B. 保护产品从运输至安装过程不受损坏。

C. Damage Responsibility: Except for damage caused by others, the installer is responsible for chipping, cracking, or other damage to GFRC parts, after delivery to the job site and until installation is complete and inspected and approved by the contractor, architect and FORM. 1.07 WARRANTY 1.07 产品保证

A. Warrant fabrications to be free from defects due to materials and workmanship. A. 保证产品没有材料及工艺方面造成的缺陷。

PART 2. PRODUCTS 第2部分 产品

2.01 FABRICATED PRODUCTS 2.01 产品制造

A. GFRC will be fabricated with a proprietary blend of cementitious minerals, aggregates, polymers and glass fibers to achieve a typical range of physical properties shown in Section 2.03 and all PCI standards whichever is greater.

A. GFRC按照专有配方制造，其中有胶凝矿物，粒料，聚合物和玻璃纤维达到指定范围的物理特性，符合第2.03条和所有PCI标准（两者取其最高标准）。

5

本文来源：https://www.bwwdw.com/article/u2pf.html