Arduino 教程--第三十三课 Arduino 鼠标按钮控制

第三十三课Arduino 鼠标按钮控制

使用鼠标库，你可以使用Arduino Leonardo，Micro或Due来控制计算机的屏幕光标。 这个特殊的例子使用五个按钮来移动屏幕上的光标。四个按钮是方向性的（上，下，左，右），一个是用于鼠标左键单击。来自Arduino的光标移动总是相对的。每次读取输入时，光标的位置都会相对于当前位置进行更新。

只要有一个方向按钮被按下，Arduino就会移动鼠标，在合适的方向上将HIGH输入映射到5的范围。

第五个按钮用于控制来自鼠标的左键单击。当按钮被释放时，计算机将识别事件。

必需的组件

? ? ? ?

你将需要以下组件：

1 × Breadboard 面包板

1 × Arduino Leonardo, Micro 或 Due板 5 × 10k欧姆电阻 5 × 瞬时按钮

程序

按照电路图连接面包板上的组件，如下图所示。

草图

在计算机上打开Arduino IDE软件。使用Arduino语言进行编码控制你的电路。通过单击“New”打开一个新的草图文件。

对于本例，你需要使用Arduino IDE 1.6.7

Arduino代码

/* Button Mouse Control For Leonardo and Due boards only .Controls the mouse from five pushbuttons on an Arduino Leonardo, Micro or Due. Hardware: * 5 pushbuttons attached to D2, D3, D4, D5, D6 The mouse movement is always relative. This sketch reads four pushbuttons, and uses them to set the movement of the mouse. WARNING: When you use the Mouse.move() command, the Arduino takes over your mouse! Make sure you have control before you use the mouse commands. */ #include \// set pin numbers for the five buttons: const int upButton = 2;

const int downButton = 3; const int leftButton = 4; const int rightButton = 5; const int mouseButton = 6; int range = 5; // output range of X or Y movement; affects movement speed int responseDelay = 10; // response delay of the mouse, in ms void setup() { // initialize the buttons' inputs: pinMode(upButton, INPUT); pinMode(downButton, INPUT); pinMode(leftButton, INPUT); pinMode(rightButton, INPUT); pinMode(mouseButton, INPUT); // initialize mouse control: Mouse.begin(); } void loop() { // read the buttons: int upState = digitalRead(upButton); int downState = digitalRead(downButton); int rightState = digitalRead(rightButton); int leftState = digitalRead(leftButton); int clickState = digitalRead(mouseButton); // calculate the movement distance based on the button states: int xDistance = (leftState - rightState) * range; int yDistance = (upState - downState) * range; // if X or Y is non-zero, move: if ((xDistance != 0) || (yDistance != 0)) { Mouse.move(xDistance, yDistance, 0); } // if the mouse button is pressed: if (clickState == HIGH) { // if the mouse is not pressed, press it: if (!Mouse.isPressed(MOUSE_LEFT)) { Mouse.press(MOUSE_LEFT); } } else { // else the mouse button is not pressed: // if the mouse is pressed, release it: if (Mouse.isPressed(MOUSE_LEFT)) { Mouse.release(MOUSE_LEFT); } } // a delay so the mouse does not move too fast: delay(responseDelay); } 代码说明

使用micro-USB线将电路板连接到计算机。按钮连接到引脚2至6的数字输入。确保使用10k下拉电阻。

本文来源：https://www.bwwdw.com/article/t5bd.html