MAX6386LT29D7+T中文资料
更新时间:2023-04-24 23:49:01 阅读量: 实用文档 文档下载
- max638plus推荐度:
- 相关推荐
General Description The MAX6381–MAX6390 microprocessor (μP) supervisory circuits monitor power-supply voltages from +1.8V to +5.0V while consuming only 3μA of supply current at +1.8V. Whenever V CC falls below the factory-set reset thresholds, the reset output asserts and remains assert-ed for a minimum reset timeout period after V CC rises above the reset threshold. Reset thresholds are available from +1.58V to +4.63V, in approximately 100mV incre-ments. Seven minimum reset timeout delays ranging from 1ms to 1200ms are available.
The MAX6381/MAX6384/MAX6387 have a push-pull active-low reset output. The MAX6382/MAX6385/ MAX6388 have a push-pull active-high reset output, and the MAX6383/MAX6386/MAX6389/MAX6390 have an open-drain active-low reset output. The MAX6384/MAX6385/MAX6386 also feature a debounced manual reset input (with internal pullup resistor). The MAX6387/MAX6388/MAX6389 have an auxiliary input for monitoring a second voltage. The MAX6390 offers a manual reset input with a longer V CC reset timeout period (1120ms or 1200ms) and a shorter manual reset timeout (140ms or 150ms).
The MAX6381/MAX6382/MAX6383 are available in 3-pin SC70 and6-pinμDFN packages and the MAX6384–MAX6390 are available in 4-pin SC70 and
Features
?Factory-Set Reset Threshold Voltages Ranging
from +1.58V to +4.63V in Approximately 100mV
Increments
?±2.5% Reset Threshold Accuracy Over
Temperature (-40°C to +125°C)
?Seven Reset Timeout Periods Available: 1ms,
20ms, 140ms, 280ms, 560ms, 1120ms,
1200ms (min)
?3 Reset Output Options
Active-Low Push-Pull
Active-High Push-Pull
Active-Low Open-Drain
?Reset Output State Guaranteed Valid
Down to V CC= 1V
?Manual Reset Input (MAX6384/MAX6385/MAX6386)
?Auxiliary RESET IN
(MAX6387/MAX6388/MAX6389)
?V CC Reset Timeout (1120ms or 1200ms)/Manual
Reset Timeout (140ms or 150ms) (MAX6390)
?Negative-Going V CC Transient Immunity
?Low Power Consumption of 6μA at +3.6V
and 3μA at +1.8V
?Pin Compatible with
MAX809/MAX810/MAX803/MAX6326/MAX6327/
MAX6328/MAX6346/MAX6347/MAX6348,
and MAX6711/MAX6712/MAX6713
?Tiny 3-Pin/4-Pin SC70 and 6-Pin μDFN Packages
MAX6381–MAX6390
SC70/μDFN, Single/Dual Low-Voltage,
Low-Power μP Reset Circuits
________________________________________________________________Maxim Integrated Products1
Pin Configurations
19-1839; Rev 4; 4/07
Ordering Information
Ordering Information continued at end of data sheet.
Typi cal Operati ng Ci rcui t appears at end of data sheet.
Selector Guide appears at end of data sheet.
after "XR", "XS", or "LT." Insert reset timeout delay (see Reset
Timeout Delay table) after "D" to complete the part number.
Sample stock is generally held on standard versions only (see
Standard Versions table). Standard versions have an order
increment requirement of 2500 pieces. Nonstandard versions
have an order increment requirement of 10,000 pieces.
Contact factory for availability of nonstandard versions.
+Denotes a lead-free package.
For pricing, delivery, and ordering information,please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at 49829a32580216fc700afd09.
Computers
Controllers
Intelligent Instruments
Critical μP and μC
Power Monitoring
Portable/Battery-
Powered Equipment
Dual Voltage Systems
元器件交易网49829a32580216fc700afd09
M A X 6381–M A X 6390
SC70/μDFN, Single/Dual Low-Voltage, Low-Power μP Reset Circuits
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(V CC = full range, T A = -40°C to +125°C, unless otherwise specified. Typical values are at T A = +25°C.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
V CC to GND..........................................................-0.3V to +6.0V RESET Open-Drain Output....................................-0.3V to +6.0V RESET , RESET (push-pull output)..............-0.3V to (V CC + 0.3V)MR , RESET IN.............................................-0.3V to (V CC + 0.3V)Input Current (V CC ).............................................................20mA Output Current (all pins).....................................................20mA
Continuous Power Dissipation (T A = +70°C)
3-Pin SC70 (derate 2.9mW/°C above +70°C)..............235mW 4-Pin SC70 (derate 3.1mW/°C above +70°C)..............245mW 6-Pin μDFN (derate 2.1mW/°C above +70°C)..........167.7mW Operating Temperature Range .........................-40°C to +125°C Storage Temperature Range.............................-65°C to +150°C Lead Temperature (soldering, 10s).................................+300°C
元器件交易网49829a32580216fc700afd09
MAX6381–MAX6390SC70/μDFN, Single/Dual Low-Voltage, Low-Power μP Reset Circuits
_______________________________________________________________________________________3
元器件交易网49829a32580216fc700afd09
M A X 6381–M A X 6390
SC70/μDFN, Single/Dual Low-Voltage, Low-Power μP Reset Circuits 4______________________________________________________________________________________
Typical Operating Characteristics
(T A = +25°C, unless otherwise noted.)
215436789-40-105-25203550658095110125
SUPPLY CURRENT vs. TEMPERATURE
(NO LOAD)
TEMPERATURE (°C)
S U P P L Y C U R R E N T (μA )
25
292735333137394143
-40-105-2520355065
8095110125
POWER-DOWN RESET DELAY
vs. TEMPERATURE
TEMPERATURE (°C)
P O W E R -D O W N R E S E T D E L A Y (μs )
0.94
0.980.961.021.001.061.041.08-40-10520-253550658095110125
NORMALIZED POWER-UP RESET TIMEOUT
vs. TEMPERATURE
M A X 6381/90 t o c 03
TEMPERATURE (°C)
N O R M A L I Z E D R E S E T T I M E O U T P E R I O D
0.990
0.985
1.0150.9950.9901.0001.0051.0101.020-40-10520-253550958011065125
M A X 6381/90 t o c 04
TEMPERATURE (°C)
N O R M A L I Z E D R E S E T T
H R E S H O L D NORMALIZED RESET THRESHOLD
vs. TEMPERATURE
00.40.20.8
0.6
1.01.20
63
9
12
OUTPUT-VOLTAGE LOW vs. SINK CURRENT
I SINK (mA)
V O L (V )
01.0
0.52.01.52.53.00
500
750
250
1000
1250
1500
OUTPUT-VOLTAGE HIGH vs. SOURCE CURRENT
I SOURCE (μA)
V O H (V )
4500
1
1000100
10
MAXIMUM TRANSIENT DURATION vs. RESET COMPARATOR OVERDRIVE
15050350250500
200100400300RESET COMPARATOR OVERDRIVE, V TH - V CC (mV)
M A X I M U M T R A N S I E N T D U R A T I O N (μs )
3.5
3.93.7
4.54.34.14.74.9
5.35.15.5
-40-105-25203550658095110125
RESET IN TO RESET DELAY
vs. TEMPERATURE
M A X 6381/90 t o c 08
TEMPERATURE (°C)
R E S E T I N D E L A Y (μs )
元器件交易网49829a32580216fc700afd09
MAX6381–MAX6390SC70/μDFN, Single/Dual Low-Voltage, Low-Power μP Reset Circuits
Pin Description
元器件交易网49829a32580216fc700afd09
M A X 6381–M A X 6390
SC70/μDFN, Single/Dual Low-Voltage, Low-Power μP Reset Circuits 6_______________________________________________________________________________________
Detailed Description
RESET Output
A μP reset input starts the μP in a known state. These μP supervisory circuits assert reset to prevent code execution errors during power-up, power-down, or brownout conditions.
Reset asserts when V CC is below the reset threshold;once V CC exceeds the reset threshold, an internal timer keeps the reset output asserted for the reset timeout period. After this interval, reset output deasserts. Reset output is guaranteed to be in the correct logic state for V CC ≥1V.
Manual Reset Input (MAX6384/MAX6385/MAX6386/MAX6390)
Many μP-based products require manual reset capabil-ity, allowing the operator, a test technician, or external logic circuitry to initiate a reset. A logic low on MR asserts reset. Reset remains asserted while MR is low,and for the reset active timeout period (t RP ) after MR returns high. This input has an internal 63k ?pullup resistor (1.56k ?for MAX6390), so it can be left uncon-nected if it is not used. MR can be driven with TTL or CMOS logic levels, or with open-drain/collector outputs.Connect a normally open momentary switch from MR to G ND to create a manual-reset function; external debounce circuitry is not required. If MR is driven from long cables or if the device is used in a noisy environ-ment, connecting a 0.1μF capacitor from MR to G ND provides additional noise immunity.
RESET IN Comparator
(MAX6387/MAX6388/MAX6389)
RESET IN is compared to an internal +1.27V reference.If the voltage at RESET IN is less than 1.27V, reset asserts. Use the RESET IN comparator as a user-adjustable reset detector or as a secondary power-sup-ply monitor by implementing a resistor-pider at RESET IN (shown in Figure 1). Reset asserts when either V CC or RESET IN falls below its respective threshold volt-age. Use the following equation to set the threshold:
V INTH = V THRST (R1/R2 + 1)where V THRST = +1.27V. To simplify the resistor selec-tion, choose a value of R2 and calculate R1:
R1 = R2 [(V INTH /V THRST ) - 1]
Since the input current at RESET IN is 50nA (max),large values can be used for R2 with no significant loss in accuracy.
___________Applications Information
Negative-Going V CC Transients
In addition to issuing a reset to the μP during power-up,power-down, and brownout conditions, the MAX6381–MAX6390 are relatively immune to short dura-tion negative-going V CC transients (glitches).
The Typical Operating Characteristics section shows the Maximum Transient Durations vs. Reset Comparator Overdrive, for which the MAX6381–MAX6390 do not generate a reset pulse. This graph was generated using
元器件交易网49829a32580216fc700afd09
a negative-going pulse applied to V CC , starting above the actual reset threshold and ending below it by the magnitude indicated (reset comparator overdrive). The graph indicates the typical maximum pulse width a neg-
ative-going V CC transient may have without causing a reset pulse to be issued. As the magnitude of the tran-sient increases (goes farther below the reset threshold),the maximum allowable pulse width decreases. A 0.1μF capacitor mounted as close as possible to V CC provides
additional transient immunity.Ensuring a Valid RESET Output Down to V CC = 0V
The MAX6381–MAX6390 are guaranteed to operate properly down to V CC = 1V. In applications that require
valid reset levels down to V CC = 0V, a pulldown resistor to active-low outputs (push/pull only, Figure 2) and a pullup resistor to active-high outputs (push/pull only)
will ensure that the reset line is valid while the reset out-put can no longer sink or source current. This scheme does not work with the open-drain outputs of the MAX6383/MAX6386/MAX6389/MAX6390. The resistor
value used is not critical, but it must be small enough
not to load the reset output when V CC is above the
reset threshold. For most applications, 100k ?is ade-
quate.
MAX6381–MAX6390SC70/μDFN, Single/Dual Low-Voltage, Low-Power μP Reset Circuits
_______________________________________________________________________________________7
元器件交易网49829a32580216fc700afd09
M A X 6381–M A X 6390
SC70/μDFN, Single/Dual Low-Voltage, Low-Power μP Reset Circuits 8
_______________________________________________________________________________________
Selector Guide
Ordering Information (continued)
Note:Insert reset threshold suffix (see Reset Threshold table)after "XR", "XS", or "LT." Insert reset timeout delay (see Reset Timeout Delay table) after "D" to complete the part number.Sample stock is generally held on standard versions only (see Standard Versions table). Standard versions have an order increment requirement of 2500 pieces. Nonstandard versions have an order increment requirement of 10,000 pieces.Contact factory for availability of nonstandard versions.*MAX6390 is available with D4 or D7 timing only.+Denotes a lead-free package.
元器件交易网49829a32580216fc700afd09
MAX6381–MAX6390SC70/μDFN, Single/Dual Low-Voltage, Low-Power μP Reset Circuits
_______________________________________________________________________________________9Chip Information
TRANSISTOR COUNT: 647
PROCESS: BiCMOS
Pin Configurations (continued)
元器件交易网49829a32580216fc700afd09
M A X 6381–M A X 6390SC70/μDFN, Single/Dual Low-Voltage, Low-Power μP Reset Circuits
10______________________________________________________________________________________
Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,go to 49829a32580216fc700afd09/packages .)元器件交易网49829a32580216fc700afd09
MAX6381–MAX6390SC70/μDFN, Single/Dual Low-Voltage, Low-Power μP Reset Circuits
______________________________________________________________________________________11
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,go to 49829a32580216fc700afd09/packages .)
元器件交易网49829a32580216fc700afd09
M
A X 6381–M A X 6390SC70/μDFN, Single/Dual Low-Voltage, Low-Power μP Reset Circuits
12______________________________________________________________________________________
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,go to 49829a32580216fc700afd09/packages .)元器件交易网49829a32580216fc700afd09
SC70/μDFN, Single/Dual Low-Voltage, Low-Power μP Reset Circuits
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600____________________13?2007 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc.MAX6381–MAX6390
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,go to 49829a32580216fc700afd09/packages .)
Revision History
Pages changed at Rev 4: Title on all pages, 1, 2, 5,
7–13
元器件交易网49829a32580216fc700afd09
正在阅读:
MAX6386LT29D7+T中文资料04-24
热学答案第二版(完整版)解析 - 李椿 - 章立源等著11-23
四年级下书法教案06-10
抗震期末复习答案10-25
体格检查复习题及答案12-16
20种绝对成交的销售话术 - 图文09-24
PLC与文本屏、编码器、变频器程序实例-彩钢瓦裁切控制程序 - 图文10-11
多芬企业网络整合营销案例分析01-30
盾构施工安全保证措施04-18
- 教学能力大赛决赛获奖-教学实施报告-(完整图文版)
- 互联网+数据中心行业分析报告
- 2017上海杨浦区高三一模数学试题及答案
- 招商部差旅接待管理制度(4-25)
- 学生游玩安全注意事项
- 学生信息管理系统(文档模板供参考)
- 叉车门架有限元分析及系统设计
- 2014帮助残疾人志愿者服务情况记录
- 叶绿体中色素的提取和分离实验
- 中国食物成分表2020年最新权威完整改进版
- 推动国土资源领域生态文明建设
- 给水管道冲洗和消毒记录
- 计算机软件专业自我评价
- 高中数学必修1-5知识点归纳
- 2018-2022年中国第五代移动通信技术(5G)产业深度分析及发展前景研究报告发展趋势(目录)
- 生产车间巡查制度
- 2018版中国光热发电行业深度研究报告目录
- (通用)2019年中考数学总复习 第一章 第四节 数的开方与二次根式课件
- 2017_2018学年高中语文第二单元第4课说数课件粤教版
- 上市新药Lumateperone(卢美哌隆)合成检索总结报告
- 中文
- 资料
- 6386
- MAX
- LT
- 29
- 经济管理第一次作业
- 教育心理学试题 有答案
- 微机原理与接口技术 第5章
- 银行员工述职报告精选范文5篇
- 美丽的浙江热门景点导游词范文5篇
- 2019-2020学年度第二学期幼儿园中班班级工作总结与2019-2020学年
- 生态学名词解释+填空+简答+论述 考研必备
- 公司财务审批权限规定
- 新版河北工业大学电子信息考研经验考研参考书考研真题
- 建设工程施工安全标准化管理资料
- XX年度安全质量年终工作总结
- 2017年安徽财经大学经济学综合(西方经济学、政治经济学、世界经
- 数控车床编程与操作课程标准
- 寒假土地局社会实践报告范文
- 技术标、商务标(样本)
- 2020最新咨询工程师宏观经济政策与发展规划题库及答案
- 2019-2020北京四中初二第一学期数学期中考试
- 反假考试练习题500道
- 西安交通大学近几年各专业录取免试生人数统计
- 新版译林英语8A单词表