TI DRV8846 3D打印机马达控制器参考设计 - 图文
更新时间:2024-03-02 23:49:01 阅读量: 综合文库 文档下载
- tiktok推荐度:
- 相关推荐
TI DRV8846 3D打印机马达控制器参考设计
关键字:马达驱动,3D打印机,DRV8846
TI公司的DRV8846是高度集成的步进马达驱动器,包括两个H桥和微步进分度器,工作电压4-18V,驱动电流高达1A,主要用在打印机,扫描仪,视频安全摄像机和投映仪.本文介绍了DRV8846主要特性,功能框图,应用电路以及评估板主要特性,电路图和材料清单,以及3D打印机控制器(12V)主要特性,电路图和材料清单.
The DRV8846 provides a highly-integrated stepper motor driver for cameras, printers, projectors, and other automated equipment applications. The device has two H-bridges and a microstepping indexer and is intended to drive a bipolar stepper motor. The output block of each H-bridge driver consists of N- channel and P-channel power MOSFETs configured as full H-bridges to drive the motor windings. The DRV8846 is capable of driving up to 1-A full scale output current (with proper heatsinking and TA = 25℃).
A simple STEP/DIR interface allows easy interfacing to controller circuits. Pins allow configuration of the motor in full-step up to 1/32-step modes. Decay mode is configurable so that adaptive decay, slow decay, fast decay, and mixed decay can be used. The PWM
current chopping off-time can also be selected. A low-power sleep mode is provided which shuts down internal circuitry to achieve very-low quiescent current draw. This sleep mode can be set using a dedicated nSLEEP pin.
Internal protection functions are provided for UVLO,overcurrent protection, short circuit protection, and overtemperature. Fault conditions are indicated via a nFAULT pin.
DRV8846主要特性:
1? PWM Microstepping Motor Driver – Built-In Microstepping Indexer – Up to 1/32 Microstepping – Step/Direction Control ? Multiple Decay Modes – Adaptive Decay – Mixed Decay
– Slow Decay
– Fast Decay
? Configurable Off-Time PWM Chopping – 10-, 20-, or 30-μs Off-Time
? Adaptive Blanking Time for Smooth Stepping ? 4- to 18-V Operating Supply Voltage Range ? 1-A Continuous/RMS Output Current (at 25℃) ? Low-Current Sleep Mode
? 3-Bit Torque DAC to Scale Motor Current ? Thermally Enhanced Surface Mount Package ? Protection Features
– VM Undervoltage Lockout (UVLO) – Overcurrent Protection (OCP) – Thermal Shutdown (TSD)
– Fault Condition Indication Pin (nFAULT) DRV8846主要应用: ? Printers ? Scanners
? Video Security Cameras ? Projectors
图1. DRV8846功能框图
图2. DRV8846 PWM马达驱动器电路图
图3. DRV8846 典型应用电路图
评估板
The DRV8846 customer EVM is a platform revolving around the DRV8846, a low voltage dual H-bridge driver and highly configurable power stage. This device has been optimized to drive a single bipolar stepper with up to 32 degrees of internally generated microstepping.
The EVM houses an MSP430 microcontroller and a USB interface chip. The USB chip allows for serial communications from a PC computer where a Microsoft? Windows? application is used to schedule serial commands. These commands can be used to control each of the device’s signals, and drive the stepper motor by issuing the step commands at the desired rate.
The microcontroller firmware operates using internal index mode.
This user’s guide details the operation of the EVM, as well as the hardware configurability of the evaluation module.
图4.评估板PCB外形图
图5.评估板连接图
图6.评估板电路图(1)
图7.评估板电路图(2) 评估板材料清单:
3D打印机控制器(12V)
This design is a complete system for controlling 3-axis, single extruder-based 3D printers. The system is managed by the MSP430F5529 LaunchPad and utilizes the DRV8846 for precision stepper motor control. The CSD18534Q5A is used as a low-side switch for the hot bed heater, extruder heater, and cooling fan. The DRV5033 Hall Sensor acts as a contactless limit switch.
3D打印机控制器(12V)主要特性:
Complete 3D printer controller with MCU, stepper drivers, heater outputs, sensor inputs, and SD card slot.
Precise stepper motor current regulation using DRV8846 adaptive decay Hall sensor limit switches are immune to contaminants and never wear out High-current heater outputs from the CSD18534Q5A with low 7.8 m? Rds(ON) Powered from a single 12V supply
System has been fully tested and proven
图8.3D打印机TIDA-00405外形图
图9.3D打印机TIDA-00405电路图(1)
图10.3D打印机TIDA-00405电路图(2)
图11.3D打印机TIDA-00405电路图(3)
图12.3D打印机TIDA-00405电路图(4)
图13.3D打印机TIDA-00405电路图(5) 3D打印机TIDA-00405系统材料清单:
正在阅读:
TI DRV8846 3D打印机马达控制器参考设计 - 图文03-02
2018年4月自考02141计算机网络技术试卷及答案解释05-17
华南师大高级英语散文赏析 翻译04-25
父母对我的爱作文400字07-09
交通安全观后感550字最新05-12
党史党课主持词07-31
残疾人社会保障事业发展的思路与对策01-20
关于孙家口水库的调研报告04-14
【考试重点】最新版七年级英语上册 Unit 7 How much are these socks Section A(1a-2e)同步练习09-07
- 多层物业服务方案
- (审判实务)习惯法与少数民族地区民间纠纷解决问题(孙 潋)
- 人教版新课标六年级下册语文全册教案
- 词语打卡
- photoshop实习报告
- 钢结构设计原理综合测试2
- 2014年期末练习题
- 高中数学中的逆向思维解题方法探讨
- 名师原创 全国通用2014-2015学年高二寒假作业 政治(一)Word版
- 北航《建筑结构检测鉴定与加固》在线作业三
- XX县卫生监督所工程建设项目可行性研究报告
- 小学四年级观察作文经典评语
- 浅谈110KV变电站电气一次设计-程泉焱(1)
- 安全员考试题库
- 国家电网公司变电运维管理规定(试行)
- 义务教育课程标准稿征求意见提纲
- 教学秘书面试技巧
- 钢结构工程施工组织设计
- 水利工程概论论文
- 09届九年级数学第四次模拟试卷
- 马达
- 控制器
- 打印机
- DRV8846
- 参考
- 图文
- 设计
- TI
- 学校2017-2018学年信访工作计划3篇
- 宾馆饭店消防安全四个能力
- 风门施工安全技术措施
- 如何培养一年级学生行为习惯
- 井田概况及地质特征 - 图文
- 西南交大ANSYS作业 - 图文
- 后进生的特点、成因及转化策略的探析
- 2015年班组安全活动计划
- 电子商务基础与实训任务安排
- 中国硫化镍行业市场前景分析预测年度报告(目录) - 图文
- 改进合作学习第二讲检测答案
- 消防保卫管理制度
- 2009年版二级VFP第8套题
- 爱科中文版通用标准
- 通信技术专业毕业论文设计
- 工程技术资料检查记录(设备安装) - 图文
- 外研版 英语 七年级上 重点句子
- 信号与系统复习试题(含答案)
- 最新袜子营销营销策划书精选
- 上海职工晋升技师、高级技师奖励申请表 - 图文