ccs认可试验大纲2013-6-18 - 图文

更新时间:2024-05-07 03:29:01 阅读量: 综合文库 文档下载

说明:文章内容仅供预览,部分内容可能不全。下载后的文档,内容与下面显示的完全一致。下载之前请确认下面内容是否您想要的,是否完整无缺。

认可试验大纲 第 1 页 共 28 页

常州船用电缆有限责任公司

认 可 试 验 大 纲

认可试验大纲 第 2 页 共 28 页

序号 型号规格 CEF/SA 3×95 CJPJ95/NSC 3×50 CKJ86/SC 7×1.5 CHJPJP95/SC 10×2×1.5 JKYJQ85/SC 7×0.35 JHRP85/SC 7×2×0.6 JYJPJ85/SC-1 19×1.5 JQYJ75/SC 3×16 CJPF80/SC 3×1 CEV/SA 3×1 CJV/SA 3×1 CJ86/NSC 7×1.5 JEPJR/SC 1×240 JKYJPQ85/SC 19×1 JHYJPQ85/SC 24×2×0.75 JEPJR/SC-A 3×120 试验场所:国家电线电缆质量监督检验中心

0.6/1 1.8/3 0.15/0.25 0.15/0.25 0.6 0.3 1 0.6/1 0.6/1 0.6/1 0.6/1 0.6/1 0.6/1 0.6 0.3 0.6/1 电压等级(kV) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 认可试验大纲 第 3 页 共 28 页

试验样品名称: 试样型号/规格:

序号 乙丙橡皮绝缘氯丁护套阻燃船用电力电缆,SA型

CEF/SA 3×95mm2 0.6 / 1 kV 技术要求/Requirement 试验方法/Testing Method 试验项目/Test 1 1.1 1.2 电缆结构尺寸检查/Check of cable dimensions 导体检查/Conductor examination 绝缘厚度/Measurement of thickness of insulation 非金属护套厚度/Measurements of thickness of non-metallic sheaths 外径/Measurement of external diameter 电性能/Electrical 绝缘电阻试验(20℃) /Insulation resistance at ambient temperature(20℃) 最高工作温度时绝缘电阻测量(90℃)/ Insulation resistance at maximum rated temperature(90℃) 导体电阻测量/Measurement of the electrical resistance of the conductors 4h高压试验/High-voltage test for 4h up to 1.8/3kV 浸水后电容增值测量/Increase in a.c. capacitance after immersion in water 非电性能/Non-electrical IEC60228:2004 表Ⅱ IEC60092-353:2011 第5.3.3条 IEC60092-353:2011 第5.9.3条 IEC60092-350:2008第6.4条 IEC60092-350:2008 第6.5条 IEC60092-350:2008 第6.6条 IEC60092-350:2008 附录A计算 IEC60092-350:2008 第6.7条 2 2.1 IEC60092-351:2004 表2 IEC60092-350:2008第7.2.1条 2.2 IEC60092-351:2004 表2 IEC60092-350:2008第7.2.2条 2.3 IEC60228:2004表2 IEC60092-350:2008 第5.2.2条 2.4 2.5 IEC60092-350:2008 第7.4.1条 IEC60092-351:2004 表2 IEC60092-350:2008 第7.4条 IEC60092-350:2008 第7.3条 3 3.1 3.1.1 绝缘的机械性能试验/Mechanical properties of insulation 空气箱老化前后机械性能IEC60092-351:2004 表3 试验/Tests for determining the mechanical properties of insulation before and after ageing 空气弹老化试验IEC60092-351:2004 表3 /Mechanical characteristic after ageing in air bomb 绝缘的特殊性能试验/Special properties test of insulation IEC60092-350:2008第8.3条 3.1.2 IEC60092-350:2008第8.3条 3.2 3.2.1 3.2.2 3.3 3.3.1 热延伸试验/Hot-set test for IEC60092-351:2004 表4 IEC60092-350:2008第6.8条 insulations 耐臭氧试验/Ozone IEC60092-351:2004 表4 IEC60092-350:2008第8.13条 resistance test for insulation 护套的机械性能试验/Mechanical properties of inter sheath and outer sheath 空气箱老化前后机械性能试验/Tests for determining the mechanical properties of sheaths before and after ageing IEC60092-359:1999 表Ⅱ IEC60092-350:2008第8.4条 认可试验大纲 第 4 页 共 28 页

3.3.2 3.3.3 3.4 3.4.1 3.5 浸热油试验/Hot oil IEC60092-359:1999 表Ⅱ immersion test 护套热延伸试验/Hot-set IEC60092-359:1999 表Ⅱ test for sheaths 护套的特殊性能试验/Special properties test of sheaths 耐臭氧试验/Ozone resistance test for sheaths 附加老化相容性试验/Additional ageing test on pieces of completed cables (compatibility test) 铜丝镀层试验/Test of the metal coating of copper wires 燃烧试验/Fire tests 播焰(燃烧)试验/Flame-spread test IEC60092-350:200第8.13.2条 IEC60092-351:2004 表3 IEC60092-359:1999 表Ⅱ IEC60092-350:2008第8.10条 IEC60092-350:2008第8.14.1条 IEC60092-350:2008第6.8条 IEC60092-350:2008第8.13.1条 IEC60092-350:2008第8.5条 3.6 IEC60092-350:2008第8.10条 3.7 3.7.1 3.8 标识耐久性/Durability of print 试验报告要求: 1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果;

5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)。

IEC60092-350:2008 第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC60092-350:2008第8.19条 IEC60092-350:2008 第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC60092-350:2008第8.19条 认可试验大纲 第 5 页 共 28 页

试验样品名称: 试样型号/规格:

序号 交联聚乙烯绝缘交联聚烯烃内套镀锌钢丝编织铠装交联聚烯烃外套低烟无卤船用

耐火电力电缆,NSC型

CJPJ95/NSC 3×50mm2 1.8 / 3 kV

技术要求/Requirement 试验方法/Testing Method 试验项目/Test 1 1.1 1.2 电缆结构尺寸检查/Check of cable dimensions 导体检查/Conductor examination 绝缘厚度/Measurement of thickness of insulation 非金属护套厚度/Measurement of thickness of non metallic sheaths 外径/Measurement of external diameter 编织覆盖密度(编织铠装电缆)/Coverage density of braid (Braid armored Cables) 电性能/Electrical 绝缘电阻试验(20℃) /Insulation resistance at ambient temperature(20℃) 最高工作温度时绝缘电阻测量(90℃)/ Insulation resistance at maximum rated temperature(90℃) 导体电阻测/Measurement of electrical resistance of the conductors 4h高压试验/High-voltage tests for 4h up to 1.8/3kV 非电性能/Non-electrical IEC60228:2004 表Ⅱ IEC60092-353:2011 第5.3.3条 IEC60092-353:2011 第5.7.3条 IEC60092-353:2011 第5.9.3条 IEC60092-350:2008 附录A计算 IEC60092-350:2008第4.8.2条 IEC60092-350:2008第6.4条 IEC60092-350:2008 第6.5条 IEC60092-350:2008 第6.6条 IEC60092-350:2008 第6.7条 IEC60092-350:2008 第4.8.2条 1.3 2 2.1 IEC60092-351:2004 表2 IEC60092-350:2008第7.2.1条 2.2 IEC60092-351:2004 表2 IEC60092-350:2008第7.2.2条 2.3 IEC60228:2004表2 IEC60092-350:2008 第5.2.2条 2.4 IEC60092-350:2008 第7.4.1条 IEC60092-350:2008 第7.4条 3 3.1 3.1.1 绝缘的机械性能试验/Mechanical properties of insulation 空气箱老化前后机械性能IEC60092-351:2004 表3 试验/Tests for determining the mechanical properties of insulation before and after ageing 绝缘的特殊性能试验/Special properties test of insulation IEC60092-350:2008第8.3条 3.2 3.2.1 3.3 3.3.1 热延伸试验/Hot-set test for IEC60092-351:2004 表4 IEC60092-350:2008第6.8条 insulations 内外护套的机械性能试验/Mechanical properties of inter sheath and outer sheath 空气箱老化前后机械性能IEC60092-359:1999 表Ⅱ 试验/Tests for determining the mechanical properties of sheaths before and after ageing 浸热油试验/Hot oil IEC60092-359:1999 表Ⅱ immersion test 热延伸试验/Hot-set test of IEC60092-359:1999 表Ⅱ sheaths 内外护套的特殊性能试验/Special properties test of sheaths IEC60092-350:2008第8.4条 3.3.2 3.3.3 3.4 IEC60092-350:2008第8.14.1条 IEC60092-350:2008第6.8条

认可试验大纲 第 6 页 共 28 页

3.4.1 3.4.2 3.4.3 3.5 3.6 3.7 3.8 3.8.1 低温拉伸试验/Elongation test for low temperature behaviour 低温冲击试验/Shock test for low temperature behaviour 耐臭氧试验/Ozone resistance test for sheaths 附加老化相容性试验/Additional ageing test on pieces of completed cables (compatibility test) 铜丝镀层试验/Test for the metal coating of copper wires 钢丝镀锌层试验/Galvanizing test 燃烧试验/Fire tests 播焰(燃烧)试验/Flame-spread tests IEC60092-350:2008第8.8.2条 IEC60092-350:2008第8.8.1条 IEC60092-350:2008第8.8.2条 IEC60092-350:2008第8.8.1条 IEC60092-350:2008第8.13.2条 IEC60092-351:2004 表3 IEC60092-359:1999 表Ⅱ IEC60092-350:2008第8.10条 IEC60092-350:2008第8.13.1条 IEC60092-350:2008第8.5条 IEC60092-350:2008第8.10条 IEC60092-350:2008第8.11条 ISO 7989-2 第5.3条 3.8.2 3.8.3 3.8.4 3.8.5 3.8.6 烟释放试验/Smoke emission test 酸性气体释放量试验/Acid gas emission test pH值和电导率试验/pH and conductivity test 氟含量试验/Fluorine content test 耐火试验/Fire-resistance test 标识耐久性/Durability of print IEC60092-350:2008 第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC60092-350:2008第8.16.3条 IEC60092-350:2008第4.1.4条 IEC60092-350:2008第4.1.4条 IEC60092-350:2008第4.1.4条 IEC60092-350:200第8.16.7条 IEC60331-1:2009(电缆外径大于20mm) IEC60092-350:2008第8.19条 IEC60092-350:2008第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC61034-1:2005 IEC61034-2:2005 IEC60092-350:2008第8.16.4条 IEC 60754-1:2011 IEC60092-350:2008第8.16.5条 IEC 60754-2:2011 IEC60092-350:2008第8.16.6条 IEC 60684-2:2011 IEC60092-350:2008第8.16.7条 IEC60331-1:2009(电缆外径大于20mm) IEC60092-350:2008第8.19条 3.9

试验报告要求:

1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果;

5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)。

认可试验大纲 第 7 页 共 28 页

试验样品名称: 试样型号/规格:

序号 交联聚乙烯绝缘镀锡铜丝编织铠装热塑性聚烯烃外套低烟无卤阻燃船用控制电缆,

SC型

CKJ86/SC 7×1.5mm2 0.15 / 0.25 kV 技术要求/Requirement 试验方法/Testing Method 试验项目/Test 1 1.1 1.2 电缆结构尺寸检查/Check of cable dimensions 导体检查/Conductor examination 绝缘厚度/Measurement of thickness of insulation 非金属护套厚/Measurement of thickness of non-metallic sheaths 外径/Measurement of external diameter 编织覆盖密度(编织铠装电缆)/Coverage density of braid (Braid armored Cables) 电性能/Electrical IEC60228:2004 表Ⅱ IEC60092-350:2008第6.4条 IEC60092-376:2003第10.4条表2 IEC60092-350:2008 第6.5条 IEC60092-376:2003 第14.1条 IEC60092-350:2008 第6.6条 IEC60092-350:2008 附录A计算 IEC60092-350:2008第4.8.2条 IEC60092-350:2008 第6.7条 IEC60092-350:2008第4.8.2条 1.3 2 2.1 2.2 3 3.1 3.1.1 绝缘电阻试验IEC60092-351:2004 表2 (20℃)/Insulation resistance at ambient temperature(20℃) 导体电阻测量IEC60092-376:2003第9条表6 /Measurement of electrical resistance of the conductors 非电性能/Non-electrical 绝缘的机械性能试验/Mechanical properties of insulation 空气箱老化前后机械性能IEC60092-351:2004 表3 试验/Tests for determining the mechanical properties of insulation before and after ageing 绝缘的特殊性能试验/Special properties test of insulation 热延伸试验/Hot-set test for IEC60092-351:2004 表4 insulations 护套的机械性能试验/Mechanical properties of sheath 空气箱老化前后机械性能IEC60092-359:1999 表Ⅱ 试验/Tests for determining the mechanical properties of sheaths before and after ageing 护套的特殊性能试验/Special properties test of sheath 高温压力试验/Hot pressure test 热冲击试验/Heat shock test 低温拉伸试验/Elongation test for low temperature behaviour IEC60092-359:1999 表Ⅲ IEC60092-350:2008第8.12.2条 IEC60092-350:2008第8.8.2条 IEC60092-350:2008第7.2.1条 IEC60092-350:2008第5.2.2条 IEC60092-350:2008第8.3条 3.2 3.2.1 3.3 3.3.1 IEC60092-350:2008第6.8条 IEC60092-350:2008第8.4条 3.4 3.4.1 3.4.2 3.4.3 IEC60092-350:2008第8.7.1条 IEC60092-350:2008第8.12.1条 IEC60811-3-1第9条 IEC60092-350:2008第8.8.1条 认可试验大纲 第 8 页 共 28 页

3.4.4 3.5 3.6 3.7 3.7.1 低温冲击试验/Shock test for low temperature behaviour 附加老化相容性试验/Additional ageing test on pieces of completed cables (compatibility test) 铜丝镀层试验/Test for the metal coating of copper wires 燃烧试验/Fire tests 播焰(燃烧)试验/Flame-spread tests IEC60092-350:2008第8.8.2条 IEC60092-350:2008第8.8.1条 IEC60092-351:2004 表3 IEC60092-359:1999 表Ⅱ IEC60092-350:2008第8.10条 IEC60092-350:2008第8.5条 IEC60092-350:2008第8.10条 3.7.2 3.7.3 3.7.4 3.7.5 3.8 烟释放试验/Smoke emission test 酸性气体释放量试验/Acid gas emission test pH值和电导率试验/pH and conductivity test 氟含量试验/Fluorine content test 标识耐久性/Durability of print IEC60092-350:2008 第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC60092-350:2008第8.16.3条 IEC60092-350:2008第4.1.4条 IEC60092-350:2008第4.1.4条 IEC60092-350:2008第4.1.4条 IEC60092-350:2008 第8.19条

IEC60092-350:2008第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC61034-1:2005 IEC61034-2:2005 IEC60092-350:2008第8.16.4条 IEC 60754-1:2011 IEC60092-350:2008第8.16.5条 IEC 60754-2:2011 IEC60092-350:2008第8.16.6条 IEC 60684-2:2011 IEC60092-350:2008第8.19条 试验报告要求:

1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果;

5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)。

认可试验大纲 第 9 页 共 28 页

试验样品名称: 试样型号/规格:

序号 交联聚乙烯绝缘单独屏蔽交联聚烯烃内套镀锌钢丝编织铠装交联聚烯烃外套低烟

无卤阻燃船用仪表电缆,SC型

CHJPJP95/SC 10×2×1.5mm2 0.15 / 0.25 kV 技术要求/Requirement 试验方法/Testing Method 试验项目/Test 1 1.1 1.2 电缆结构尺寸检查/Check of cable dimensions 导体检查/Conductor examination 绝缘厚度/Measurement of thickness of insulation 非金属护套厚度/Measurement of thickness of non-metallic sheaths 外径/Measurement of external diameter 编织覆盖密度(编织铠装电缆)/Coverage density of braid (Braid armored Cables) 电性能/Electrical 绝缘电阻试验(20℃) /Insulation resistance at ambient temperature(20℃) 屏蔽间绝缘电阻(20℃)/Screen insulation resistance(20℃) 屏蔽和铠装间绝缘电阻/Insulation resistance between any screen and the armour 导体电阻测量/Measurement of the electrical resistance of the conductors 泄漏线电阻/Drain wire resistance 工作电容/Mutual capacitance 电感电阻比/Inductance to resistance tatio 非电性能/Non-electrical IEC60228:2004表Ⅱ IEC60092-350:2008第6.4条 IEC60092-376:2003第10.4条表2 IEC60092-350:2008第6.5条 IEC60092-376:2003第14.1条 IEC60092-350:2008第6.6条 IEC60092-350:2008附录A计算 IEC60092-350:2008第4.8.2条 IEC60092-350:2008第6.7条 IEC60092-350:2008第4.8.2条 1.3 2 2.1 IEC60092-351:2004表2 IEC60092-350:2008第7.2.1条 2.2 IEC60092-376:2003第17.1 条 IEC60092-350:2008第5.2.4条 2.3 IEC60092-376:2003第17.1条 IEC60092-350:2008第5.2.4条 2.4 IEC60092-376:2003第9条表6 IEC60092-350:2008第5.2.2条 2.5 2.6 2.7 IEC60092-376:2003第12.2条表3 IEC60092-350:2008第5.2.2条 IEC60092-350:2008第7.5条 IEC60092-350:2008 第7.6条 IEC60092-350:2008第7.5条 IEC60092-350:2008 第7.6条 3 3.1 3.1.1 绝缘的机械性能试验/Mechanical properties of insulation 空气箱老化前后机械性能IEC60092-351:2004 表3 试验/Tests for determining the mechanical properties of insulation before and after ageing 绝缘的特殊性能试验/Special properties test of insulation IEC60092-350:2008第8.3条 3.2 3.2.1 3.3 热延伸试验/Hot-set test for IEC60092-351:2004 表4 IEC60092-350:2008第6.8条 insulations 内外护套的机械性能试验/Mechanical properties of inter sheath and outer sheath 认可试验大纲 第 10 页 共 28 页

3.3.1 3.3.2 3.3.3 3.4 3.4.1 空气箱老化前后机械性能IEC60092-359:1999 表Ⅱ 试验/Tests for determining the mechanical properties of sheaths before and after ageing 浸热油试验/Hot oil IEC60092-359:1999 表Ⅱ immersion test 热延伸试验/Hot-set test for IEC60092-359:1999 表Ⅱ sheaths 护套的特殊性能试验/Special properties test of sheath 低温拉伸试验/Elongation test for low temperature behaviour 低温冲击试验/Shock test for low temperature behaviour 耐臭氧试验/Ozone resistance test for sheaths 附加老化相容性试验/Additional ageing test on pieces of completed cables (compatibility test) 铜丝镀层试验/Test for the metal coating of copper wires 钢丝镀锌层试验/Galvanizing test 燃烧试验/Fire tests 播焰(燃烧)试验/Flame-spread tests IEC60092-350:2008第8.8.2条 IEC60092-350:2008第8.4条 IEC60092-350:2003第8.14.1条 IEC60092-350:2008第6.8条 IEC60092-350:2008第8.8.1条 3.4.2 IEC60092-350:2008第8.8.2条 IEC60092-350:2008第8.8.1条 3.4.3 3.5 IEC60092-350:2008第8.13.2条 IEC60092-351:2004 表3 IEC60092-359:1999 表Ⅱ IEC60092-350:2008第8.10条 IEC60092-350:2008第8.13.1条 IEC60092-350:2008第8.5条 3.6 IEC60092-350:2008第8.10条 3.7 3.8 3.8.1 IEC60092-350:2008第8.11条 ISO 7989-2 第5.3条 3.8.2 烟释放试验/Smoke emission test 3.8.3 酸性气体释放量试验/Acid IEC60092-350:2008第4.1.4条 IEC60092-350:2008第8.16.4条 gas emission test IEC 60754-1:2011 3.8.4 pH值和电导率试验/pH IEC60092-350:2008第4.1.4条 IEC60092-350:2008第8.16.5条 and conductivity test IEC 60754-2:2011 3.8.5 氟含量试验/Fluorine IEC60092-350:2008第4.1.4条 IEC60092-350:2008第8.16.6条 content test IEC 60684-2:2011 3.9 标识耐久性/Durability of IEC60092-350:2008第8.19条 IEC60092-350:2008第8.19条 print 试验报告要求: 1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果;

5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)。

IEC60092-350:2008 第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC60092-350:2008第8.16.3条 IEC60092-350:2008第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC61034-1:2005 IEC61034-2:2005

认可试验大纲 第 11 页 共 28 页

试验样品名称: 试样型号/规格:

序号 交联聚乙烯绝缘镀锡铜丝铠装交联聚烯烃护套轻型无卤低烟低毒舰船用控制电缆,

SC型

JKYJQ85/SC 7×0.35mm2 0.6 kV 技术要求 企标Q/3204ADS010-2013表14-16 GJB 1916-94 表1-1 企标Q/3204ADS010-2013第12.3条 试验方法 GJB 1916-94 第4.5.3条 GJB 1916-94 第4.5.2条 GJB 1916-94 第4.5.4条 试验项目 质量一致性检验项目 绝缘电阻试验(20℃) 直流电阻测试 高压试验 导体和屏蔽连续性 电缆外观尺寸检查 撕裂强度 绝缘老化前后机械性能试验 护套老化前后机械性能试验 绝缘印字耐久性 护套印字耐久性 热变形试验 热收缩试验 抗拉强度和伸长率 鉴定检验项目 电缆老化和相容性试验 酸气含量 卤素含量 A类成束垂直燃烧 浸油试验 烟指数 毒性指数 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12 1.13 企标Q/3204ADS010-2013第12.15条 GJB 1916-94 第4.5.42条 企标Q/3204ADS010-2013第12.6条,GJB 1916-94 第4.5.1条 第12.7条,第12.8条和第12.12条 企标Q/3204ADS010-2013第10.1条 GJB 1916-94 第4.5.30条 企标Q/3204ADS010-2013第6.2条和GJB 1916-94 第4.5.10条 第10.1条 企标Q/3204ADS010-2013第6.2条和GJB 1916-94 第4.5.10条 第10.1条 企标Q/3204ADS010-2013第12.13条 GJB 1916-94 第4.5.26条 企标Q/3204ADS010-2013第12.11条GJB 1916-94 第4.5.27条 和第12.13条 企标Q/3204ADS010-2013第6.2条和GJB 1916-94 第4.5.15条 第10.1条 企标Q/3204ADS010-2013第12.14条 GJB 1916-94 第4.5.40条 企标Q/3204ADS010-2013第6.2条和第10.1条 企标Q/3204ADS010-2013第12.9条 企标Q/3204ADS010-2013第6.2条和第10.1条 企标Q/3204ADS010-2013第6.2条和第10.1条 企标Q/3204ADS010-2013第12.10条 企标Q/3204ADS010-2013第10.1条 企标Q/3204ADS010-2013第6.2条和第10.1条 企标Q/3204ADS010-2013第6.2条和第10.1条 企标Q/3204ADS010-2013第10.1条 企标Q/3204ADS010-2013第10.1条 GJB 1916-94 第4.5.10条 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 GJB 1916-94 第4.5.18条 GJB 1916-94 第4.5.34条 GJB 1916-94 第4.5.35条 GB/T 18380.33-2008 GJB 1916-94 第4.5.39条 GJB 1916-94 第4.5.36条 GJB 1916-94 第4.5.37条 硬度 GJB 1916-94 第4.5.28条 耐磨 GJB 1916-94 第4.5.11条 试验报告要求: 1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果; 5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)。

认可试验大纲 第 12 页 共 28 页

试验样品名称: 试样型号/规格:

序号 交联聚烯烃绝缘镀锡铜丝线对屏蔽镀锡铜丝铠装交联聚烯烃护套轻型薄壁无卤低烟

无卤舰船用信号通信电缆,SC型

JHRP85/SC 7×2×0.6mm2 0.3 kV 技术要求 试验方法 试验项目 质量一致性检验项目 绝缘电阻试验(20℃) 直流电阻测试 高压试验 屏蔽间绝缘电阻 电缆外观和尺寸检查 工作电容 电容不平衡 特性阻抗 撕裂强度 绝缘老化前后机械性能试验 护套老化前后机械性能试验 护套印字耐久性 热变形试验 热收缩试验 鉴定检验项目 酸气含量 卤素含量 A类成束垂直燃烧 浸油试验 烟指数 毒性指数 硬度 耐磨 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12 1.13 1.14 企标Q/3204ADS003-2013第9.2条 GJB 1916-94 第4.5.3条 企标Q/3204ADS003-2013第9.4条 企标Q/3204ADS003-2013第9.3条 企标Q/3204ADS003-2013第9.7条 企标Q/3204ADS003-2013第8条和第9.1条 企标Q/3204ADS003-2013第9.5条 企标Q/3204ADS003-2013第9.6条 企标Q/3204ADS003-2013第9.8条 企标Q/3204ADS003-2013第7.1条 企标Q/3204ADS003-2013第5.2条和第7.1条 企标Q/3204ADS003-2013第5.2条和第7.1条 企标Q/3204ADS003-2013第9.9条和第9.11条 企标Q/3204ADS003-2013第5.2条和第7.1条 企标Q/3204ADS003-2013第7.1条 GJB 1916-94 第4.5.2条 GJB 1916-94 第4.5.4条 GJB 1916-94 第4.5.3条 GJB 1916-94 第4.5.1条 GJB 1916-94 第4.5.6条 GJB 1916-94 第4.5.6条 GJB 1916-94 第4.5.7条 GJB 1916-94 第4.5.30条 GJB 1916-94 第4.5.10条 GJB 1916-94 第4.5.10条 GJB 1916-94 第4.5.27条 GJB 1916-94 第4.5.15条 GJB 1916-94 第4.5.40条 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 企标Q/3204ADS003-2013第5.2条和第7.1条 企标Q/3204ADS003-2013第5.2条和第7.1条 GJB 1916-94 第4.5.34条 GJB 1916-94 第4.5.35条 企标Q/3204ADS003-2013第9.9条 GB/T 18380.33-2008 企标Q/3204ADS003-2013第7.1条 GJB 1916-94 第4.5.39条 企标Q/3204ADS003-2013第5.2条GJB 1916-94 第4.5.36条 和第7.1条 企标Q/3204ADS003-2013第5.2条GJB 1916-94 第4.5.37条 和第7.1条 企标Q/3204ADS003-2013第7.1条 GJB 1916-94 第4.5.28条 企标Q/3204ADS003-2013第7.1条 GJB 1916-94 第4.5.11条 试验报告要求: 1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果; 5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)。

认可试验大纲 第 13 页 共 28 页

试验样品名称: 试样型号/规格:

序号 交联聚乙烯绝缘交联聚烯烃内套镀锡铜丝编织铠装交联聚烯烃外套低烟无卤舰船用

电力电缆,SC型

JYJPJ85/SC-1 19×1.5mm2 1 kV 技术要求 IEC60228:2004 表Ⅱ Q/3204 ADS034-2013表7~30的规定 Q/3204 ADS034-2013表7~30的规定 Q/3204 ADS034-2013表7~30的规定 IEC60092-350:2008第4.8.2条 试验方法 IEC60092-350:2008第6.4条 IEC60092-350:2008 第6.5条 IEC60092-350:2008 第6.6条 IEC60092-350:2008 第6.7条 IEC60092-350:2008第4.8.2条 试验项目 电缆结构尺寸检查 导体检查 绝缘厚度 非金属护套厚度 外径 1 1.1 1.2 1.3 2 2.1 2.2 2.3 2.4 编织覆盖密度(编织铠装电缆) 电性能 绝缘电阻试验(20℃) 工作温度绝缘电阻试验 导体电阻测量 Q/3204 ADS034-2013表7~30的规定 IEC60092-350:2008第7.2.1条 Q/3204 ADS034-2013表7~30的规定 IEC60092-350:2008第7.2.2条 IEC60228:2004表2 IEC60092-350:2008 第5.2.2条 IEC60092-350:2008 第7.4条 3 3.1 3.1.1 3.2 3.2.1 3.3 3.3.1 3.3.2 3.3.3 3.4 3.4.1 3.4.2 3.4.3 3.5 3.6 3.7 3.7.1 3.7.2 4h高压试验 Q/3204 ADS034-2013第5.2.2条的 规定 非电性能 绝缘的机械性能试验 空气箱老化前后机械性能试验 绝缘的特殊性能试验 热延伸试验 护套的机械性能试验 空气箱老化前后机械性能试验 护套浸热油试验 护套热延伸试验 护套的特殊性能试验 护套低温拉伸试验 护套低温冲击试验 护套耐臭氧试验 附加老化相容性试验 IEC60092-350:2008第8.8.2条 IEC60092-350:2008第8.8.2条 IEC60092-350:2008第8.13.2条 IEC60092-359:1999 表Ⅱ IEC60092-359:1999 表Ⅱ IEC60092-359:1999 表Ⅱ IEC60092-351:2004 表3 IEC60092-350:2008第8.3条 IEC60092-351:2004 表4 IEC60092-350:2008第6.8条 IEC60092-350:2008第8.4条 IEC60092-350:2008第8.14条 IEC60092-350:2008第6.8条 IEC60092-350:2008第8.8.1条 IEC60092-350:2008第8.8.1条 IEC60092-350:2008第8.13.1条 IEC60092-350:2008第8.5条 IEC60092-350:2008第8.10条 IEC60092-351:2004 表3 IEC60092-359:1999 表Ⅱ 铜丝镀层试验 IEC60092-350:2008 第8.10条 燃烧试验 A类成束电缆火焰蔓延试验 酸气含量 IEC 60332-3-22:2009 企标Q/3204ADS034-2013第5.4、5.5条 IEC60092-350:2008第8.16.2条 GJB 1916-94 第4.5.34条 认可试验大纲 第 14 页 共 28 页

3.7.3 3.7.4 3.7.5 3.8 3.9 烟指数 卤素含量 毒性指数 标识耐久性 企标Q/3204ADS034-2013第5.4、GJB 1916-94 第4.5.36条 5.5条 企标Q/3204ADS034-2013第5.5条 GJB 1916-94 第4.5.35条 企标Q/3204ADS034-2013第5.4、5.5条 IEC60092-350:2008第8.19条 GJB 1916-94 第4.5.37条 IEC60092-350:2008第8.19条 载流量试验 企标Q/3204ADS034-2013第5.6条 企标Q/3204ADS034-2013第5.6条 试验报告要求: 1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果; 5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)。

认可试验大纲 第 15 页 共 28 页

试验样品名称: 试样型号/规格:

序号 交联聚乙烯绝缘铝合金丝编织铠装交联聚烯烃外套舰船用低烟轻型电力电缆

JQYJ75/SC 3×16mm2 0.6/1 kV 技术要求 试验方法 试验项目 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12 1.13 1.14 质量一致性检验项目 企标Q/3204ADS011-2013第4.8.1.3绝缘电阻试验(20℃) GJB 1916-94 第4.5.3条 条 直流电阻测试 企标Q/3204ADS011-2013第4.2.2条 GJB 1916-94 第4.5.2条 企标Q/3204ADS011-2013第4.8.1.2高压试验 GJB 1916-94 第4.5.4条 条 企标Q/3204ADS011-2013第4.8.1.4导体和铠装连续性 GJB 1916-94 第4.5.42条 条 Q/3204ADS011-2013第4.8.3条电缆外观尺寸检查 企标 GJB 1916-94 第4.5.1条 及表6 企标Q/3204ADS011-2013第4.8.2.5电缆低温弯曲试验 GJB 1916-94 第4.5.20条 条 Q/3204ADS011-2013第4.3.5.1热延伸试验 企标 GB/T 2951.21-2008 条和第4.7.4条 撕裂强度 企标Q/3204ADS011-2013第4.7.4条 GJB 1916-94 第4.5.30条 绝缘老化前后机械性能试企标Q/3204ADS011-2013第4.3.5.1GJB 1916-94 第4.5.10条 验 条和第4.7.4条 护套老化前后机械性能试企标Q/3204ADS011-2013第4.3.5.1GJB 1916-94 第4.5.10条 验 条和第4.7.4条 Q/3204ADS011-2013第4.1.2.2护套印字耐久性 企标 GJB 1916-94 第4.5.27条 条 铠装 企标Q/3204ADS011-2013第4.6.1条 GJB 1916-94 第4.5.31条 热变形试验 企标Q/3204ADS010-2013第4.3.5.1GJB 1916-94 第4.5.15条 条和第4.7.4条 热收缩试验 企标Q/3204ADS010-2013第4.8.2.6GJB 1916-94 第4.5.40条 条 鉴定检验项目 电缆老化和相容性试验 酸气含量 卤素含量 A类成束垂直燃烧/A类成束电缆火焰蔓延试验 浸油试验 烟指数 毒性指数 企标Q/3204ADS011-2013第4.8.2.4条 GJB 1916-94 第4.5.18条 2 2.1 2.2 2.3 企标Q/3204ADS011-2013第4.3.5.1 GJB 1916-94 第4.5.34条 4.5.3和4.7.4条 企标Q/3204ADS011-2013第4.5.3条和第4.7.4条 企标Q/3204ADS011-2013第4.8.2.7条 企标Q/3204ADS011-2013第4.7.4条 GJB 1916-94 第4.5.35条 GB/T 18380.33-2008 GJB 1916-94 第4.5.39条 2.4 2.5 2.6 2.7 企标Q/3204ADS010-2013第4.3.5.1 GJB 1916-94 第4.5.36条 4.5.3和4.7.4条 企标Q/3204ADS010-2013第4.3.5.1 GJB 1916-94 第4.5.37条 4.5.3和4.7.4条

认可试验大纲 第 16 页 共 28 页

2.8 2.9 2.10 2.11 硬度 耐气候试验 耐磨 重量 企标Q/3204ADS011-2013第4.7.4条 企标Q/3204ADS011-2013第4.7.4条 企标Q/3204ADS011-2013第4.7.4条 企标Q/3204ADS011-2013第4.8.4条 GJB 1916-94 第4.5.28条 GJB 1916-94 第4.5.38条 企标Q/3204ADS011-2013附录A 企标Q/3204ADS011-2013附录B

试验报告要求:

1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果;

5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)。

认可试验大纲 第 17 页 共 28 页

试验样品名称: 试样型号/规格:

序号 1 1.1 1.2 交联聚乙烯绝缘热塑性聚烯烃内套铜丝或铜合金丝编织铠装低烟无卤船用耐火电力

电缆,SC型

CJPF80/SC 3×1mm2 0.6/1 kV

技术要求/Requirement 试验方法/Testing Method 试验项目/Test 电缆结构尺寸检查/Check of cable dimensions 导体检查/Conductor examination 绝缘厚度/Measurement of thickness of insulation 非金属护套厚度/Measurement of thickness of non-metallic sheaths 外径/Measurement of external diameter 编织覆盖密度(编织铠装电缆)/Coverage density of braid (Braid armored Cables) 电性能/Electrical 绝缘电阻试验(20℃) /Insulation resistance at ambient temperature(20℃) 最高工作温度时绝缘电阻测量(90℃)/ Insulation resistance at maximum rated temperature(90℃) 导体电阻测量/Measurement of the electrical resistance of the conductors 4h高压试验/High-voltage test for 4h 非电性能/Non-electrical IEC60228:2004 表Ⅱ IEC60092-353:2011 第5.3.3条 IEC60092-353:2011 第5.7.3条 IEC60092-353:2011 第5.9.3条 IEC60092-350:2008 附录A计算 IEC60092-350:2008第4.8.2条 IEC60092-350:2008第6.4条 IEC60092-350:2008 第6.5条 IEC60092-350:2008 第6.6条 IEC60092-350:2008 第6.7条 IEC60092-350:2008 第4.8.2条 1.3 2 2.1 IEC60092-351:2004 表2 IEC60092-350:2008第7.2.1条 2.2 IEC60092-351:2004 表2 IEC60092-350:2008第7.2.2条 2.3 IEC60228:2004表2 IEC60092-350:2008 第5.2.2条 2.4 IEC60092-350:2008 第7.4.1条 IEC60092-350:2008 第7.4条 3 3.1 3.1.1 绝缘的机械性能试验/Mechanical properties of insulation 空气箱老化前后机械性能IEC60092-351:2004 表3 试验/Tests for determining the mechanical properties of insulation before and after ageing 绝缘的特殊性能试验/Special properties test of insulation 热延伸试验/Hot-set test for IEC60092-351:2004 表4 insulations 护套的机械性能试验/Mechanical properties of sheath 空气箱老化前后机械性能IEC60092-359:1999 表Ⅱ 试验/Tests for determining the mechanical properties of sheaths before and after ageing 护套的特殊性能试验/Special properties test of sheath 高温压力试验/Hot pressure test IEC60092-359:1999 表Ⅲ IEC60092-350:2008第8.3条 3.2 3.2.1 3.3 3.3.1 IEC60092-350:2008第6.8条 IEC60092-350:2008第8.4条 3.4 3.4.1 IEC60092-350:2008第8.7.1条 认可试验大纲 第 18 页 共 28 页

3.4.2 3.4.3 3.4.4 3.5 3.6 3.7 3.7.1 热冲击试验/Heat shock test 低温弯曲试验/Bend test for low temperature behaviour 低温冲击试验/Shock test for low temperature behaviour 附加老化相容性试验/Additional ageing test on pieces of completed cables (compatibility test) 铜丝镀层试验/Test for the metal coating of copper wires 燃烧试验/Fire tests 播焰(燃烧)试验/Flame-spread tests IEC60092-350:2008第8.12.2条 IEC60092-350:2008第8.8.2条 IEC60092-350:2008第8.12.1条 IEC60811-3-1第9条 IEC60092-350:2008第8.8.1条 IEC60092-350:2008第8.8.2条 IEC60092-350:2008第8.8.1条 IEC60092-351:2004 表3 IEC60092-359:1999 表Ⅱ IEC60092-350:2008第8.10条 IEC60092-350:2008第8.5条 IEC60092-350:2008第8.10条 3.7.2 烟释放试验/Smoke emission test 3.7.3 酸性气体释放量试验 IEC60092-350:2008第4.1.4条 IEC60092-350:2008第8.16.4条 Acid gas emission test IEC 60754-1:2011 3.7.4 pH值和电导率试验/pH IEC60092-350:2008第4.1.4条 IEC60092-350:2008第8.16.5条 and conductivity test IEC 60754-2:2011 3.7.5 氟含量试验/Fluorine IEC60092-350:2008第4.1.4条 IEC60092-350:2008第8.16.6条 content test IEC 60684-2:2011 3.8 标识耐久性/Durability of IEC60092-350:2008第8.19条 IEC60092-350:2008第8.19条 print 试验报告要求: 1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果;

5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)。

IEC60092-350:2008 第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC60092-350:2008第8.16.3条 IEC60092-350:2008第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC61034-1:2005 IEC61034-2:2005 认可试验大纲 第 19 页 共 28 页

试验样品名称: 试样型号/规格:

序号 乙丙橡皮绝缘聚氯乙烯护套镀阻燃船用电力电缆,SA型

CEV/SA 3×1mm2 0.6 / 1 kV

技术要求/Requirement 试验方法/Testing Method IEC60092-350:2008第6.4条 IEC60092-350:2008 第6.5条 IEC60092-350:2008 第6.6条 试验项目/Test 1 1.1 1.2 2 2.1 2.2 2.3 2.4 2.5 3 3.1 3.1.1 电缆结构尺寸检查/Check of cable dimensions 导体检查/Conductor IEC60228:2004 表Ⅱ examination 绝缘厚度/Measurement of IEC60092-353:2011 第5.3.3条 thickness of insulation 非金属护套厚度IEC60092-353:2011 第5.9.3条 /Measurement of thickness of non-metallic sheaths 外径/Measurement of IEC60092-350:2008 附录A计算 external diameter 电性能/Electrical 绝缘电阻试验(20℃) IEC60092-351:2004 表2 /Insulation resistance at ambient temperature(20℃) 最高工作温度时绝缘电阻IEC60092-351:2004 表2 测量(90℃)/Insulation resistance measurement at maximum rated temperature ( 90℃) 导体电阻测量IEC60228:2004表2 /Measurement of the electrical resistance of the conductors 4h高压试验 IEC60092-350:2008 第7.4.1条 High-voltage test for 4h 浸水后电容增值测量IEC60092-351:2004 表2 /Increase in a.c. capacity after immersion in water 非电性能/Non-electrical 绝缘的机械性能试验/Mechanical properties of insulation IEC60092-350:2008 第6.7条 IEC60092-350:2008第7.2.1条 IEC60092-350:2008第7.2.2条 IEC60092-350:2008 第5.2.2条 IEC60092-350:2008 第7.4条 IEC60092-350:2008 第7.3条 3.1.2 3.2 3.2.1 3.2.2 3.3 3.3.1 空气箱老化前后机械性能IEC60092-351:2004 表3 IEC60092-350:2008第8.3条 试验/Tests for determining the mechanical properties of insulation before and after ageing 空气弹老化试验IEC60092-351:2004 表3 IEC60092-350:2008第8.3条 /Mechanical properties after ageing in air bomb 绝缘的特殊性能试验/Special properties test of insulation 热延伸试验/Hot-set test for IEC60092-351:2004 表4 IEC60092-350:2008第6.8条 insulations 耐臭氧试验/Ozone IEC60092-351:2004 表4 IEC60092-350:2008第8.13条 resistance test for insulation 护套的机械性能试验/Mechanical properties of inter sheath and outer sheath 空气箱老化前后机械性能IEC60092-359:1999 表Ⅱ 试验/Tests for determining the mechanical properties of sheaths before and after ageing 护套的特殊性能试验/Special properties test of sheath IEC60092-350:2008第8.4条 3.4 认可试验大纲 第 20 页 共 28 页

3.4.1 3.4.2 3.4.3 3.4.4 3.4.5 3.5 3.6 3.7 3.7.1 高温压力试验/Hot pressure test 热冲击试验/Heat shock test 失重试验/Loss of mass test on PVC sheath 低温弯曲试验/Bend test for low temperature behaviour 低温冲击试验/Shock test for low temperature behaviour 附加老化相容性试验/Additional ageing test on pieces of completed cables (compatibility test) 铜丝镀层试验/Test for the metal coating of copper wires 燃烧试验/Fire tests 播焰(燃烧)试验/Flame-spread tests IEC60092-359:1999 表Ⅲ IEC60092-350:2008第8.12.2条 IEC60092-350:2008第8.6.2条 IEC60092-350:2008第8.8.2条 IEC60092-350:2008第8.7.1条 IEC60092-350:2008第8.12.1条 IEC60811-3-1第9条 IEC60092-350:2008第8.6.1条 IEC60092-350:2008第8.8.1条 IEC60092-350:2008第8.8.2条 IEC60092-350:2008第8.8.1条 IEC60092-351:2004 表3 IEC60092-359:1999 表Ⅱ IEC60092-350:2008第8.10条 IEC60092-350:2008第8.5条 IEC60092-350:2008第8.10条 3.8 标识耐久性/Durability of print 试验报告要求: 1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果;

5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)。

IEC60092-350:2008 第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC60092-350:2008第8.19条 IEC60092-350:2008第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC60092-350:2008第8.19条

认可试验大纲 第 21 页 共 28 页

试验样品名称: 试样型号/规格:

序号 交联聚乙烯绝缘聚氯乙烯护套镀阻燃船用电力电缆,SA型

CJV/SA 3×1mm2 0.6 / 1 kV

技术要求/Requirement 试验方法/Testing Method IEC60092-350:2008第6.4条 IEC60092-350:2008 第6.5条 IEC60092-350:2008 第6.6条 试验项目/Test 1 1.1 1.2 2 2.1 2.2 2.3 2.4 3 3.1 3.1.1 电缆结构尺寸检查/Check of cable dimensions 导体检查/Conductor IEC60228:2004 表Ⅱ examination 绝缘厚度/Measurement of IEC60092-353:2011 第5.3.3条 thickness of insulation 非金属护套厚度IEC60092-353:2011 第5.9.3条 /Measurement of thickness of non-metallic sheaths 外径/Measurement of IEC60092-350:2008 附录A计算 external diameter 电性能/Electrical 绝缘电阻试验(20℃) IEC60092-351:2004 表2 /Insulation resistance at ambient temperature(20℃) 最高工作温度时绝缘电阻IEC60092-351:2004 表2 测量(90℃)/ Insulation resistance at maximum rated temperature(90℃) 导体电阻测量IEC60228:2004表2 /Measurement of the electrical resistance of the conductors 4h高压试验/High-voltage IEC60092-350:2008 第7.4.1条 test for 4h 非电性能/Non-electrical 绝缘的机械性能试验/Mechanical properties of insulation 空气箱老化前后机械性能IEC60092-351:2004 表3 试验/Tests for determining the mechanical properties of insulation before and after ageing 绝缘的特殊性能试验/Special properties test of insulation 热延伸试验/Hot-set test for IEC60092-351:2004 表4 insulations 护套的机械性能试验/Mechanical properties of sheath 空气箱老化前后机械性能IEC60092-359:1999 表Ⅱ 试验/Tests for determining the mechanical properties of sheaths before and after ageing 护套的特殊性能试验/Special properties test of sheath 高温压力试验/Hot pressure test 热冲击试验/Heat shock test 失重试验/Loss of mass test on PVC shearhs 低温弯曲试验/Bend test for low temperature IEC60092-359:1999 表Ⅲ IEC60092-350:2008第8.12.2条 IEC60092-350:2008第8.6.2条 IEC60092-350:2008第8.8.2条 IEC60092-350:2008 第6.7条 IEC60092-350:2008第7.2.1条 IEC60092-350:2008第7.2.2条 IEC60092-350:2008 第5.2.2条 IEC60092-350:2008 第7.4条 IEC60092-350:2008第8.3条 3.2 3.2.1 3.3 3.3.1 IEC60092-350:2008第6.8条 IEC60092-350:2008第8.4条 3.4 3.4.1 3.4.2 3.4.3 3.4.4 IEC60092-350:2008第8.7.1条 IEC60092-350:2008第8.12.1条 IEC60811-3-1第9条 IEC60092-350:2008第8.6.1条 IEC60092-350:2008第8.8.1条 认可试验大纲 第 22 页 共 28 页

behaviour 3.4.5 3.5 3.6 3.7 3.7.1 低温冲击试验/Shock test for low temperature behaviour 附加老化相容性试验/Additional ageing test on pieces of completed cables (compatibility test) 铜丝镀层试验/Test for the metal coating of copper wires 燃烧试验/Fire tests 播焰(燃烧)试验/Flame-spread tests IEC60092-350:2008第8.8.2条 IEC60092-350:2008第8.8.1条 IEC60092-351:2004 表3 IEC60092-359:1999 表Ⅱ IEC60092-350:2008第8.10条 IEC60092-350:2008第8.5条 IEC60092-350:2008第8.10条 3.8 标识耐久性/Durability of print IEC60092-350:2008 第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC60092-350:2008第8.19条 IEC60092-350:2008第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC60092-350:2008第8.19条 试验报告要求:

1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果;

5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)。

认可试验大纲 第 23 页 共 28 页

试验样品名称: 试样型号/规格:

序号 1 1.1 1.2 无卤交联聚乙烯绝缘镀锡铜丝编织铠装热塑性聚烯烃护套低烟无卤阻燃耐火船用电

力电缆,NSC型

CJ86/NSC 7×1.5mm2 0.6 /1 kV

技术要求/Requirement 试验方法/Testing Method IEC60092-350:2008第6.4条 IEC60092-350:2008 第6.5条 IEC60092-350:2008 第6.6条 试验项目/Test 1.3 2 2.1 2.2 2.3 2.4 3 3.1 3.1.1 电缆结构尺寸检查/Check of cable dimensions 导体检查/Conductor IEC60228:2004 表Ⅱ examination 绝缘厚度/Measurement of IEC60092-353:2011 第5.3.3条 thickness of insulation 非金属护套厚度IEC60092-353:2011 第5.9.3条 /Measurement of thickness of non-metallic sheaths 外径/Measurement of IEC60092-350:2008 附录A计算 external diameter 编织覆盖密度(编织铠装IEC60092-350:2008第4.8.2条 电缆) Coverage density of braid (Braid armored Cables) 电性能/Electrical 绝缘电阻试验IEC60092-351:2004 表2 (20℃)/Insulation resistance at ambient temperature(20℃) 最高工作温度时绝缘电阻IEC60092-351:2004 表2 测量(90℃)/ Insulation resistance at maximum rated temperature(90℃) 导体电阻测量IEC60228:2004表2 /Measurement of the electrical resistance of the conductors 4h高压试验/High-voltage IEC60092-350:2008 第7.4.1条 test for 4h 非电性能/Non-electrical 绝缘的机械性能试验/Mechanical properties of insulation 空气箱老化前后机械性能IEC60092-351:2004 表3 试验/Tests for determining the mechanical properties of insulation before and after ageing 绝缘的特殊性能试验/Special properties test of insulation 热延伸试验/Hot-set test for IEC60092-351:2004 表4 insulation 护套的机械性能试验/Mechanical properties of sheath 空气箱老化前后机械性能IEC60092-359:1999 表Ⅱ 试验/Tests for determining the mechanical properties of sheaths before and after ageing 护套的特殊性能试验/Special property test of sheath 高温压力试验/Hot pressure test IEC60092-359:1999 表Ⅲ IEC60092-350:2008 第6.7条 IEC60092-350:2008 第4.8.2条 IEC60092-350:2008第7.2.1条 IEC60092-350:2008第7.2.2条 IEC60092-350:2008 第5.2.2条 IEC60092-350:2008 第7.4条 IEC60092-350:2008第8.3条 3.2 3.2.1 3.3 3.3.1 IEC60092-350:2008第6.8条 IEC60092-350:2008第8.4条 3.4 3.4.1 IEC60092-350:2008第8.7.1条 认可试验大纲 第 24 页 共 28 页

3.4.2 3.4.3 3.4.4 3.5 3.6 3.7 3.7.1 热冲击试验/Heat shock test 低温弯曲试验/Bend test for low temperature behaviour 低温冲击试验/Shock test for low temperature behaviour 附加老化相容性试验/Additional ageing test on pieces of completed cables (compatibility test) 铜丝镀层试验/Test for the metal coating of copper wires 燃烧试验/Fire tests 播焰(燃烧)试验/Flame-spread tests IEC60092-350:2008第8.12.2条 IEC60092-350:2008第8.8.2条 IEC60092-350:2008第8.12.1条 IEC60811-3-1第9条 IEC60092-350:2008第8.8.1条 IEC60092-350:2008第8.8.2条 IEC60092-350:2008第8.8.1条 IEC60092-351:2004 表3 IEC60092-359:1999 表Ⅱ IEC60092-350:2008第8.10条 IEC60092-350:2008第8.5条 IEC60092-350:2008第8.10条 3.7.2 3.7.3 3.7.4 3.7.5 3.7.6 烟释放试验/Smoke emission test 酸性气体释放量试验/Acid gas emission test pH值和电导率试验/pH and conductivity test 氟含量试验/Fluorine content test 耐火试验/Fire-resistance test IEC60092-350:2008 第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC60092-350:2008第8.16.3条 IEC60092-350:2008第4.1.4条 IEC60092-350:2008第4.1.4条 IEC60092-350:2008第4.1.4条 IEC60092-350:2008第8.16.7条 IEC60331-2:2009(电缆外径不大于20mm) IEC60092-350:2008第8.19条 IEC60092-350:2008第8.16.1条 IEC 600332-1-2:2004 IEC60092-350:2008第8.16.2条 IEC 60332-3-22:2009 IEC61034-1:2005 IEC61034-2:2005 IEC60092-350:2008第8.16.4条 IEC 60754-1:2011 IEC60092-350:2008第8.16.5条 IEC 60754-2:2011 IEC60092-350:2008第8.16.6条 IEC 60684-2:2011 IEC60092-350:2008第8.16.7条 IEC60331-2:2009(电缆外径不大于20mm) IEC60092-350:2008第8.19条 3.8 标识耐久性/Durability of print 试验报告要求: 1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果;

5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)。

认可试验大纲 第 25 页 共 28 页

试验样品名称: 试样型号/规格:

序号 乙丙绝缘交联聚烯烃外套无卤低烟低毒舰船用电力软电缆

JEPJR/SC 1×240mm2 0.6/1 Kv 技术要求 企标Q/3204ADS006.1-2013第10.2条 企标Q/3204ADS006.1-2013第10.1条 企标Q/3204ADS006.1-2013第10.3条 试验方法 GJB 1916-94 第4.5.3条 GJB 1916-94 第4.5.2条 GJB 1916-94 第4.5.4条 试验项目 质量一致性检验项目 绝缘电阻试验(20℃) 直流电阻测试 高压试验 电缆外观尺寸检查 电缆低温弯曲试验 撕裂强度 绝缘老化前后机械性能试验 护套老化前后机械性能试验 绝缘印字耐久性 护套印字耐久性 热变形试验 热收缩试验 鉴定检验项目 电缆老化和相容性试验 酸气含量 卤素含量 A类成束垂直燃烧/ A类成束电缆火焰蔓延试验 浸油试验 烟指数 毒性指数 硬度 耐磨 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12 企标Q/3204ADS006.1-2013第10.6 10.7, GJB 1916-94 第4.5.1条 10.8, 10.13条 企标Q/3204ADS006.1-2013第10.11条 GJB 1916-94 第4.5.20条 企标Q/3204ADS006.1-2013第8.3条 GJB 1916-94 第4.5.30条 企标Q/3204ADS006.1-2013第6.2,8.3条 GJB 1916-94 第4.5.10条 企标Q/3204ADS006.1-2013第6.2,8.3条 GJB 1916-94 第4.5.10条 企标Q/3204ADS006.1-2013第10.14条 GJB 1916-94 第4.5.26条 企标Q/3204ADS011-2013第10.12, 10.14GJB 1916-94 第4.5.27条 条 企标Q/3204ADS006.1-2013第6.2,8.3条 GJB 1916-94 第4.5.15条 企标Q/3204ADS006.1-2013第10.16条 GJB 1916-94 第4.5.40条 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 企标Q/3204ADS006.1-2013第10.9条 GJB 1916-94 第4.5.18条 企标Q/3204ADS006.1-2013第6.2,8.3条 GJB 1916-94 第4.5.34条 企标Q/3204ADS006.1-2013第6.2,8.3条 GJB 1916-94 第4.5.35条 企标Q/3204ADS006.1-2013第10.10条 企标Q/3204ADS006.1-2013第8.3条 GB/T 18380.33-2008 GJB 1916-94 第4.5.39条 企标Q/3204ADS006.1-2013第6.2,8.3条 GJB 1916-94 第4.5.36条 企标Q/3204ADS006.1-2013第6.2,8.3条 GJB 1916-94 第4.5.37条 企标Q/3204ADS006.1-2013第8.3条 企标Q/3204ADS006.1-2013第8.3条 GJB 1916-94 第4.5.28条 GJB 1916-94 第4.5.11条 试验报告要求:

1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果;

5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)。

认可试验大纲 第 26 页 共 28 页

试验样品名称: 试样型号/规格:

序号 交联聚乙烯绝缘镀锡铜丝分屏蔽镀锡铜丝铠装交联聚烯烃护套轻型无卤低烟低毒舰

船用控制电缆,SC型

JKYJPQ85/SC 19×1mm2 0.6 Kv 技术要求 企标Q/3204ADS010-2013表14-16 企标Q/3204ADS010-2013第12.1 GJB 1916-94 表1-1 企标Q/3204ADS010-2013第12.3条 企标Q/3204ADS010-2013第12.15条 企标Q/3204ADS010-2013第12.6条,第12.7条,第12.8条和第12.12条 企标Q/3204ADS010-2013第10.1条 企标Q/3204ADS010-2013第6.2条和第10.1条 企标Q/3204ADS010-2013第6.2条和第10.1条 企标Q/3204ADS010-2013第12.13条 企标Q/3204ADS010-2013第12.11条和第12.13条 企标Q/3204ADS010-2013第6.2条和第10.1条 企标Q/3204ADS010-2013第12.14条 企标Q/3204ADS010-2013第6.2条和第10.1条 企标Q/3204ADS010-2013第12.9条 企标Q/3204ADS010-2013第6.2条和第10.1条 企标Q/3204ADS010-2013第6.2条和第10.1条 企标Q/3204ADS010-2013第12.10条 企标Q/3204ADS010-2013第10.1条 企标Q/3204ADS010-2013第6.2条和第10.1条 企标Q/3204ADS010-2013第6.2条和第10.1条 企标Q/3204ADS010-2013第10.1条 企标Q/3204ADS010-2013第10.1条 试验方法 GJB 1916-94 第4.5.3条 GJB 1916-94 第4.5.2条 GJB 1916-94 第4.5.4条 GJB 1916-94 第4.5.42条 GJB 1916-94 第4.5.1条 GJB 1916-94 第4.5.30条 GJB 1916-94 第4.5.10条 GJB 1916-94 第4.5.10条 GJB 1916-94 第4.5.26条 GJB 1916-94 第4.5.27条 GJB 1916-94 第4.5.15条 GJB 1916-94 第4.5.40条 GJB 1916-94 第4.5.10条 试验项目 质量一致性检验项目 绝缘电阻试验(20℃) 直流电阻测试 高压试验 导体和屏蔽连续性 电缆外观尺寸检查 撕裂强度 绝缘老化前后机械性能试验 护套老化前后机械性能试验 绝缘印字耐久性 护套印字耐久性 热变形试验 热收缩试验 抗拉强度和伸长率 鉴定检验项目 电缆老化和相容性试验 酸气含量 卤素含量 A类成束垂直燃烧 浸油试验 烟指数 毒性指数 硬度 耐磨 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12 1.13 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 GJB 1916-94 第4.5.18条 GJB 1916-94 第4.5.34条 GJB 1916-94 第4.5.35条 GB/T 18380.33-2008 GJB 1916-94 第4.5.39条 GJB 1916-94 第4.5.36条 GJB 1916-94 第4.5.37条 GJB 1916-94 第4.5.28条 GJB 1916-94 第4.5.11条 试验报告要求: 1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果;

5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)。

认可试验大纲 第 27 页 共 28 页

试验样品名称: 试样型号/规格:

序号 交联聚乙烯绝缘镀锡铜丝分屏蔽镀锡铜丝铠装交联聚烯烃护套轻型无卤低烟低毒舰

船用信号通信电缆,SC型

JHYJPQ85/SC 24×2×0.75mm2 0.3 kV

技术要求 企标Q/3204ADS009-2013第12.2条 企标Q/3204ADS009-2013第12.4条 企标Q/3204ADS009-2013第12.3条 企标Q/3204ADS009-2013第12.8条 企标Q/3204ADS009-2013第12.10条 试验方法 GJB 1916-94 第4.5.3条 GJB 1916-94 第4.5.2条 GJB 1916-94 第4.5.4条 GJB 1916-94 第4.5.3条 GJB 1916-94 第4.5.42条 试验项目 质量一致性检验项目 绝缘电阻试验(20℃) 直流电阻测试 高压试验 屏蔽间绝缘电阻 导体和屏蔽连续性 电缆外观尺寸检查 工作电容 电容不平衡 特性阻抗 撕裂强度 绝缘老化前后机械性能试验 护套老化前后机械性能试验 护套印字耐久性 热变形试验 热收缩试验 鉴定检验项目 电缆老化和相容性试验 酸气含量 卤素含量 A类成束垂直燃烧 浸油试验 烟指数 毒性指数 硬度 耐磨 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12 1.13 1.14 1.15 企标Q/3204ADS009-2013第9条和第12.1GJB 1916-94 第4.5.1条 条 企标Q/3204ADS009-2013第12.6条 GJB 1916-94 第4.5.6条 企标Q/3204ADS009-2013第12.7条 企标Q/3204ADS009-2013第12.9条 企标Q/3204ADS009-2013第10.1条 GJB 1916-94 第4.5.6条 GJB 1916-94 第4.5.7条 GJB 1916-94 第4.5.30条 企标Q/3204ADS009-2013第6.2,10.1条 GJB 1916-94 第4.5.10条 企标Q/3204ADS009-2013第6.2,10.1条 GJB 1916-94 第4.5.10条 企标Q/3204ADS009-2013第12.11,12.13GJB 1916-94 第4.5.27条 条 企标Q/3204ADS009-2013第6.2,10.1条 GJB 1916-94 第4.5.15条 企标Q/3204ADS009-2013第10.1条 GJB 1916-94 第4.5.40条 2 2.1 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 企标Q/3204ADS009-2013第12.5条 GJB 1916-94 第4.5.18条 企标Q/3204ADS009-2013第6.2,10.1条 GJB 1916-94 第4.5.34条 企标Q/3204ADS009-2013第6.2,10.1条 GJB 1916-94 第4.5.35条 企标Q/3204ADS009-2013第12.9条 企标Q/3204ADS009-2013第10.1条 GB/T 18380.33-2008 GJB 1916-94 第4.5.39条 企标Q/3204ADS009-2013第6.2,10.1条 GJB 1916-94 第4.5.36条 企标Q/3204ADS009-2013第6.2,10.1条 GJB 1916-94 第4.5.37条 企标Q/3204ADS009-2013第10.1条 企标Q/3204ADS009-2013第10.1条 GJB 1916-94 第4.5.28条 GJB 1916-94 第4.5.11条 试验报告要求: 1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果;

5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)

认可试验大纲 第 28 页 共 28 页

试验样品名称: 试样型号/规格:

序号 乙丙绝缘交联聚烯烃外套无卤低烟低毒舰船用岸电电缆

JEPJR/SC-A 3×120mm2 0.6/1 kV

技术要求 试验方法 试验项目 质量一致性检验项目 绝缘电阻试验(20℃) 直流电阻测试 耐电压试验 电缆外观尺寸检查 电缆低温弯曲试验 撕裂强度 绝缘老化前后机械性能试验 护套老化前后机械性能试验 护套印字耐久性 热变形试验 鉴定检验项目 相容性试验 酸气含量 卤素含量 A类成束垂直燃烧/ A类成束电缆火焰蔓延试验 浸油试验 烟指数 毒性指数 耐气候 耐磨 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 企标Q/3204ACH002.1-2013第8.2条 GJB 1916-94 第4.5.3条 企标Q/3204ACH002.1-2013第8.1条 GJB 1916-94 第4.5.2条 企标Q/3204ACH002.1-2013第8.3条 GJB 1916-94 第4.5.4条 企标Q/3204ACH002.1-2013第5.1, GJB 1916-94 第4.5.1条 7.1, 8.6, 8.7, 8.8, 8.13条 企标Q/3204ACH002.1-2013第8.11GJB 1916-94 第4.5.20条 条 企标Q/3204ACH002.1-2013第8.5条 GJB 1916-94 第4.5.30条 企标Q/3204ACH002.1-2013第8.4条 GJB 1916-94 第4.5.10条 企标Q/3204ACH002.1-2013第8.5条 GJB 1916-94 第4.5.10条 企标Q/3204ACH002.1-2013第8.12GJB 1916-94 第4.5.27条 条 企标Q/3204ACH002.1-2013第8.5条 GJB 1916-94 第4.5.15条 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 企标Q/3204ACH002.1-2013第8.9条 GJB 1916-94 第4.5.18条 企标Q/3204ACH002.1-2013第8.4, GJB 1916-94 第4.5.34条 8.5条 企标Q/3204ACH002.1-2013第8.5条 GJB 1916-94 第4.5.35条 企标Q/3204ACH002.1-2013第8.10条 GB/T 18380.33-2008 企标Q/3204ACH002.1-2013第8.5条 GJB 1916-94 第4.5.39条 企标Q/3204ACH002.1-2013第8.4, GJB 1916-94 第4.5.36条 8.5条 企标Q/3204ACH002.1-2013第8.4, GJB 1916-94 第4.5.37条 8.5条 企标Q/3204ACH002.1-2013第8.5条 GJB 1916-94 第4.5.38条 企标Q/3204ACH002.1-2013第8.5条 GJB 1916-94 第4.5.11条 试验报告要求:

1, 委托方:中国船级社; 2, 来样方式:抽样;

3, 样品描述:文字、照片以及盘号;

4, 报告正文应列出:①试验项目、②实测值、③标准值、④结果;

5, 如有试验失败或不符合标准要求,则应在报告中说明该项目名称、不符合情况、整改/调整后样品描述(如适用)、具体的整改/调整措施等(整改通知单/不合格记录或其等效文件应在第一时间发至委托方,即CCS,并抄送产品制造厂)。

本文来源:https://www.bwwdw.com/article/oh5g.html

Top