思科2950交换机简明配置手册
更新时间:2024-06-16 11:30:01 阅读量: 综合文库 文档下载
2950交换机 简明配置维护手册
中望商业机器公司
2002-12-14
目录
说明 .................................................................................................................................................. 3 产品特性........................................................................................................................................... 3 配置端口........................................................................................................................................... 4
配置一组端口 ........................................................................................................................... 4 配置二层端口 ........................................................................................................................... 6
配置端口速率及双工模式 ............................................................................................... 6 端口描述 ........................................................................................................................... 7 监控及维护端口 ....................................................................................................................... 8
监控端口和控制器的状态 ............................................................................................... 8 刷新、重置端口及计数器 ............................................................................................. 10 关闭和打开端口 ............................................................................................................. 10
配置VLAN .................................................................................................................................... 11
理解VLAN ............................................................................................................................ 11 可支持的VLAN..................................................................................................................... 12 配置正常范围的VLAN ......................................................................................................... 12
生成、修改以太网VLAN ............................................................................................. 13 删除VLAN..................................................................................................................... 14 将端口分配给一个VLAN ............................................................................................. 15 配置VLAN Trunks ................................................................................................................ 16
使用STP实现负载均衡 ................................................................................................ 19
配置Cluster .................................................................................................................................... 23
说明
本手册只包括日常使用的有关命令及特性,其它未涉及的命令及特性请参考英文的详细配置手册。
产品特性
2950是只支持二层的交换机
支持VLAN
? ? ?
到250 个VLAN
支持VLAN ID从1到4094( IEEE 802.1Q 标准) 支持ISL及IEEE 802.1Q封装
安全
? ? ?
支持IOS标准的密码保护
支持标准及扩展的访问列表来定义安全策略 支持基于VLAN的访问列表
监视
? ? ?
交换机LED指示端口状态
SPAN及远端SPAN (RSPAN) 可以监视任何端口或VLAN的流量 内置支持四组的RMON监控功能(历史、统计、告警及事件)
配置端口
配置一组端口
命令 目的 Step 1 configure terminal Step 2 interface range {port-range} Step 3 进入配置状态 进入组配置状态 可以使用平时的端口配置命令进行配置 退回 Step 4 end Step 5 show interfaces [interface-id] 验证配置 Step 6 copy running-config startup-config
当使用interface range命令时有如下的规则:
?
保存 有效的组范围:
o vlan从1 到4094
o fastethernet 槽位/{first port} - {last port}, 槽位为0 o gigabitethernet槽位/{first port} - {last port},槽位为0
o port-channel port-channel-number - port-channel-number, port-channel号从1
到64
?
端口号之间需要加入空格,如:interface range fastethernet 0/1 – 5 是有效的,而interface range fastethernet 0/1-5 是无效的.
interface range 命令只能配置已经存在的interface vlan 所有在同一组的端口必须是相同类别的。
? ?
见以下例子:
Switch# configure terminal
Switch(config)# interface range fastethernet0/1 - 5
Switch(config-if-range)# no shutdown Switch(config-if-range)#
*Oct 6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up *Oct 6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to up *Oct 6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up *Oct 6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet0/4, changed state to up *Oct 6 08:24:35: %LINK-3-UPDOWN: Interface FastEthernet0/5, changed state to up *Oct 6 08:24:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/05, changed state to up
*Oct 6 08:24:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to up
*Oct 6 08:24:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up
以下的例子显示使用句号来配置不同类型端口的组:
Switch# configure terminal
Switch(config)# interface range fastethernet0/1 - 3, gigabitethernet0/1 - 2
Switch(config-if-range)# no shutdown Switch(config-if-range)#
*Oct 6 08:29:28: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up *Oct 6 08:29:28: %LINK-3-UPDOWN: Interface FastEthernet0/2, changed state to up *Oct 6 08:29:28: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to up *Oct 6 08:29:28: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to up *Oct 6 08:29:28: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to up *Oct 6 08:29:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/ 1, changed state to up
*Oct 6 08:29:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/ 2, changed state to up
*Oct 6 08:29:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/ 3, changed state to up
配置二层端口
2950的所有端口缺省的端口都是二层口,如果此端口已经配置成三层端口的话,则需要用switchport来使其成为二层端口。
配置端口速率及双工模式
可以配置快速以太口的速率为10/100Mbps及千兆以太口的速率为
10/100/1000-Mbps; 但对于GBIC端口则不能配置速率及双工模式,有时可以配置nonegotiate,当需要联接不支持自适应的其它千兆端口时 命令 目的 Step 1 configure terminal Step 2 interface 进入配置状态. 进入端口配置状态. interface-id Step 3 speed {10 | 100 | 1000 | auto | nonegotiate} 设置端口速率 注 1000 只工作在千兆口. GBIC模块只工作在1000 Mbps下. nonegotiate 只能在这些GBIC上用 1000BASE-SX, -LX, and -ZX GBIC. Step 4 duplex {auto | full | half} Step 5 end Step 6 show interfaces interface-id Step 7 copy running-config startup-config
Switch# configure terminal
Switch(config)# interface fastethernet0/3
设置全双工或半双工. 退出 显示有关配置情况 保存
Switch(config-if)# speed 10
Switch(config-if)# duplex half
端口描述
命令 目的 Step 1 configure terminal Step 2 interface interface-id Step 3 description string 进入配置模式 进入要加入描述的端口 加入描述 (最多240个字符). 退回. 验证. Step 4 end Step 5 show interfaces interface-id description or show running-config Step 6 copy running-config startup-config
保存 Use the no description interface configuration command to delete the description.
This example shows how to add a description on Fast Ethernet interface 0/4 and to verify the description:
Switch# config terminal
Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# interface fastethernet0/4
Switch(config-if)# description Connects to Marketing
Switch(config-if)# end
Switch# show interfaces fastethernet0/4 description
Interface Status Protocol Description
Fa0/4 up down Connects to Marketing
监控及维护端口
监控端口和控制器的状态
主要命令见下表:
Show Commands for Interfaces Command 目的 show interfaces [interface-id] 显示所有端口或某一端口的状态和配置. 显示一系列端口的状态或错误-关闭的状态 显示二层端口的状态,可以用来决定此口是否为二层或三层口。 显示端口描述 show interfaces interface-id status [err-disabled] show interfaces [interface-id] switchport show interfaces [interface-id] description show running-config interface [interface-id] show version
举例如下:
Switch# show interfaces status
显示当前配置中的端口配置情况 显示软硬件等情况 Port Name Status Vlan Duplex Speed Type
Gi0/1 connected routed a-full a-100 10/100/1000Base TX
Gi0/2 wce server 20.20.2 disabled routed auto auto 10/100/1000Base TX Gi0/3 ip wccp web-cache notconnect routed auto auto 10/100/1000Base TX Gi0/4 notconnect routed auto auto 10/100/1000Base TX Gi0/5 notconnect routed auto auto 10/100/1000Base TX Gi0/6 disabled routed auto auto 10/100/1000Base TX Gi0/7 disabled routed auto auto 10/100/1000Base TX Gi0/8 disabled routed auto 100 10/100/1000Base TX Gi0/9 notconnect routed auto auto 10/100/1000Base TX Gi0/10 notconnect routed auto auto 10/100/1000Base TX Gi0/11 disabled routed auto auto unknown Gi0/12 notconnect routed auto auto unknown Gi0/12 notconnect routed www.santongit.com
Switch# show interfaces fastethernet 0/1 switchport
Name: Fa0/1
Switchport: Enabled
Administrative Mode: static access Operational Mode: down
Administrative Trunking Encapsulation: dot1q Negotiation of Trunking: Off Access Mode VLAN: 1 (default)
Trunking Native Mode VLAN: 1 (default) Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001
Protected: false
Unknown unicast blocked: disabled Unknown multicast blocked: disabled
Voice VLAN: dot1p (Inactive) Appliance trust: 5
Switch# show running-config interface fastethernet0/2
Building configuration...
Current configuration : 131 bytes !
interface FastEthernet0/2 switchport mode access switchport protected no ip address mls qos cos 7 mls qos cos override end
刷新、重置端口及计数器
Clear命令 目的 clear counters [interface-id] clear line [number | console 0 | vty number]
清除端口计数器. 重置异步串口的硬件逻辑 Note clear counters 命令只清除用show interface所显示的计数,不影响用snmp得到
的计数
举例如下:
Switch# clear counters fastethernet0/5
Clear \y Switch#
*Sep 30 08:42:55: %CLEAR-5-COUNTERS: Clear counter on interface FastEthernet0/5 by vty1 (171.69.115.10)
可使用clear line 命令来清除或重置某一端口或串口,在大部分情况下并不需要这样做:
Switch# clear interface fastethernet0/5
关闭和打开端口
命令 目的 Step 1 configure terminal 进入配置状态 选择要关闭的端口 关闭 退出 验证 Step 2 interface {vlan vlan-id} | {{fastethernet | gigabitethernet} interface-id} | {port-channel port-channel-number} Step 3 shutdown Step 4 end Step 5 show running-config
使用 no shutdown 命令重新打开端口. 举例如下:
Switch# configure terminal
Switch(config)# interface fastethernet0/5 Switch(config-if)# shutdown Switch(config-if)#
*Sep 30 08:33:47: %LINK-5-CHANGED: Interface FastEthernet0/5, changed state to a administratively down
Switch# configure terminal
Switch(config)# interface fastethernet0/5 Switch(config-if)# no shutdown Switch(config-if)#
*Sep 30 08:36:00: %LINK-3-UPDOWN: Interface FastEthernet0/5, changed state to up
配置VLAN
理解VLAN
一个VLAN就是一个交换网,其逻辑上按功能、项目、应用来分而不必考虑用户的物理位置。任何交换口都可以属于某一VLAN, IP包、广播包及组播包均可以发送或广播给在此VLAN内的最终用户。每一个VLAN均可看成是一个逻辑网络,发往另一VLAN的数据包必须由路由器或网桥转发(如下图)。由于VLAN被看成是一个逻辑网络,其具有自己的网桥管理信息庫 (MIB) 并可支持自己的生成树
VLAN作为逻辑定义的网络示意图
VLAN常常与IP子网相联系,同一IP子网属于同一VLAN。在3550上VLAN之间的数据包可以由VLAN端口进行转发。
可支持的VLAN
Catalyst 3550交换机支持250个 VLAN,可以分别是VTP client, server, 及 transparent modes. VLAN号可以从1到4094. VLAN号1002到1005保留给令牌环及FDDI VLAN. VTP只能学习到普通范围的VLAN, 即从VLAN到1到1005; VLAN号大于1005属于扩展VLAN,不存在VLAN数据庫中。 交换机必须配置成VTP透明模式当需要生成VLAN 号从1006到4094.
本交换机支持基于每一VLAN的生成树(PVST),最多支持128个生成树。本交换机支持ISL及IEEE 802.1Q trunk二种封装。
配置正常范围的VLAN
VLAN号1, 1002到1005是自动生成的不能被去掉。
VLAN号1到1005的配置被写到文件vlan.dat 中, 可以用show vlan 命令查看, vlan.dat 文件存放在NVRAM中.
注意 不要手工删除vlan.dat 文件,可能造成VLAN的不完整。 如要删除vlan需要 用有关的命令来进行
生成、修改以太网VLAN
命令 目的 Step 1 configure terminal Step 2 vlan vlan-id 进入配置状态 输入一个VLAN号, 然后进入vlan配置状态,可以输入一个新的VLAN号或旧的来进行修改。 (可选)输入一个VLAN名,如果没有配置VLAN名,缺省的名字是VLAN号前面用0填满的4位数,如VLAN0004是VLAN4的缺省名字 (可选) 改变MTU大小 退出 验证 Step 3 name vlan-name Step 4 mtu mtu-size Step 5 end Step 6 show vlan {name vlan-name | id vlan-id} Step 7 copy running-config startup config (可选) 保存配置 用no vlan name 或 no vlan mtu 退回到缺省的vlan配置状态 举例如下:
Switch# configure terminal
Switch(config)# vlan 20
Switch(config-vlan)# name test20
Switch(config-vlan)# end
也可以在enable状态下,进行VLAN配置: 命令 目的 Step 1 vlan database Step 2 vlan vlan-id name vlan-name Step 3 vlan vlan-id mtu mtu-size Step 4 exit 进入VLAN配置状态 加入VLAN号及VLAN名 (可选) 修改MTU大小 更新VLAN数据庫并退出 验证配置 保存配置(可选) Step 5 show vlan {name vlan-name | id vlan-id} Step 6 copy running-config startup config
举例如下:
Switch# vlan database
Switch(vlan)# vlan 20 name test20
Switch(vlan)# exit
APPLY completed. Exiting.... Switch#
删除VLAN
当删除一个处于VTP服务器的交换机上删除VLAN时,则此VLAN将在所有相同VTP的交换机上删除。当在透明模式下删除时,只在当前交换机上删除。
注意 当删除一个VLAN时,原来属于此VLAN的端口将处于非激活的状态,直到将 其分配给某一VLAN。
命令 目的 Step 1 configure terminal Step 2 no vlan vlan-id Step 3 end Step 4 show vlan brief Step 5 copy running-config startup config
进入配置状态 删除某一VLAN. 退出 验证 保存 也可用vlan database 进入VLAN配置状态,用no vlan vlan-id 来删除。
将端口分配给一个VLAN
命令 目的 Step 1 configure terminal Step 2 interface interface-id Step 3 switchport mode access Step 4 switchport access vlan vlan-id 进入配置状态 进入要分配的端口 定义二层口 把端口分配给某一VLAN
Step 5 end Step 6 show running-config interface interface-id Step 7 show interfaces interface-id switchport Step 8 copy running-config startup-config
退出 验证端口的VLAN号 验证端口的管理模式和VLAN情况 保存配置 使用 default interface interface-id 还原到缺省配置状态。 举例如下:
Switch# configure terminal
Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# interface fastethernet0/1
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 2
Switch(config-if)# end Switch#
配置VLAN Trunks
命令 目的 Step 1 configure terminal Step 2 interface interface-id Step 3 switchport mode {dynamic {auto | desirable} | trunk} 进入配置状态 进入端口配置状态 配置二层trunk模式。 ? dynamic auto—自动协商是否成为trunk ? dynamic desirable—把端口设置为trunk如果对方端口是trunk, desirable, 或自动模式 trunk—设置端口为强制的trunk方式,而不理会对方端口是否为trunk ? Step 4 switchport access vlan vlan-id (可选) 指定一个缺省VLAN, 如果此端口不再是trunk 指定802.1Q native VLAN号 Step 5 switchport trunk native vlan vlan-id Step 6 end Step 7 show interfaces interface-id switchport Step 8 show interfaces interface-id trunk Step 9 copy running-config startup-config 举例:
Switch# configure terminal
退出 显示有关switchport 的配置 显示有关trunk的配置 保存配置 Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# interface fastethernet0/4
Switch(config-if)# switchport mode trunk
Switch(config-if)# end
定义trunk允许的VLAN
缺省情况下trunk允许所有的VLAN通过。可以使用 switchport trunk allowed vlan remove vlan-list 来去掉某一VLAN
Command Purpose Step 1 configure terminal Step 2 interface interface-id Step 3 switchport mode trunk Step 4 switchport trunk allowed vlan {add | all | except | remove} vlan-list 进入配置状态 进入端口配置 配置二层口为trunk (可选) 配置trunk允许的VLAN. 使用add, all, except, remove关健字 Step 5 end Step 6 show interfaces interface-id switchport Step 7 copy running-config startup-config
退出 验证VLAN配置情况. 保存配置 回到允许所有VLAN通过时, 可用no switchport trunk allowed vlan 端口配置命令. 举例如下:
Switch(config)# interface fastethernet0/1
Switch(config-if)# switchport trunk allowed vlan remove 2
Switch(config-if)# end
配置Native VLAN(802.1q)
封装802.1q的trunk端口可以接受带有标签和不带标签的数据流,交换机向native vlan传送不带标签的数据流,缺省情况下native VLAN是1。
命令 目的 Step 1 configure terminal Step 2 interface interface-id 进入配置状态 进入配置成802.1qtrunk的端口 配置native VLAN号 Step 3 switchport trunk native vlan vlan-id Step 4 end Step 5 show interfaces interface-id switchport Step 6 copy running-config startup-config
退出 验证native VLAN配置 保存配置 使用no switchport trunk native vlan 端口配置命令回到缺省的状态
使用STP实现负载均衡
负载均衡可以使用流量分流到其它平行的trunks上去. 交换机为了避免环路, STP通常是阻断所有端口交换机之间只留一条链路 。使用负载均衡后, 可以把不同VLAN的流量分配到不同的trunk上。
可以通过配置STP端口权值STP路径值来实现负载均衡. 如果使用STP端口权值来配置那么二条负载均衡的trunk必须联同一交换机上。使用路径值则即可以联相同的交换机与可以联不同的交换机。 使用STP端口权值的负载均衡
当同一台交换机的二个口形成环路时, STP端口权值用来决定那个口是enable的,那个口是阻断的。 可以通过配置端口权值来决定二对trunk各走那些VLAN, 有较高权值的端口(数字较小的)vlan, 将处于转发状态,同一个VLAN在另一个trunk有较低的权值(数字较大)则将处在阻断状态。 即同一VLAN只在一个trunk上发送接受。
基于端口权值的负载均衡示意图
trunk1将发送和接收VLAN8-10的数据,trunk2将发送和接收VLAN3-6的数据
配置如下: Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Command Purpose configure terminal vtp domain domain-name vtp server end show vtp status show vlan configure terminal interface fastethernet 0/1 switchport mode trunk 进入Switch 1配置状态 配置VTP域 将Switch 1配置成VTP server. 退出 验证VTP的配置 验证VLAN 进入配置状态 进入F0/1端口 配置成trunk端口 退出 验证VLAN配置 Step 10 end Step 11 show interfaces fastethernet0/1 switchport Step 12 在switch1上的F0/2上重复7到11步骤 在Switch 2的F0/1,F0/2上重复7到11步骤。 Step 13
Step 14 show vlan 当trunk已经起来,在switch2上验证已经学到相关的vlan配置 在Switch 1上进入配置状态 进入要配置的端口 将端口权值10赋与VLAN 8. Step 15 configure terminal Step 16 interface fastethernet0/1 Step 17 spanning-tree vlan 8 port-priority 10 Step 18 spanning-tree vlan 9 port-priority 10 Step 19 spanning-tree vlan 10 port-priority 10 Step 20 exit Step 21 Step 22 interface fastethernet0/2 spanning-tree vlan 3 port-priority 10 spanning-tree vlan 4 port-priority 10 spanning-tree vlan 5 port-priority 10 spanning-tree vlan 6 port-priority 10 end 将端口权值10赋与VLAN 9. 将端口权值10赋与VLAN 10. 退回. 进入F0/2 将端口权值10赋与VLAN 3. Step 23 将端口权值10赋与VLAN 4. Step 24 将端口权值10赋与VLAN 5. Step 25 将端口权值10赋与VLAN 10. Step 26 退出 验证配置 保存配置 Step 27 show running-config Step 28 copy running-config startup-config
配置STP路径值的负载均衡
也可以通过配置配置STP路径值来实现负载均衡,如下图所示 Trunk1走VLAN8-10,Trunk2走VLAN2-4
Step 1 Step 2 命令 目的 configure terminal interface fastethernet 0/1 switchport mode trunk exit end show running-config show vlan configure terminal 进入 Switch 1配置状态 进入F0/1 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 配置Trunk,只能是dot1q模式 退回 在F0/2口上重复2-4步骤 退出 验证配置 验证switch1已经学到Vlan 进入配置状态 进入F0/1 Step 10 interface fastethernet 0/1 Step 11 spanning-tree vlan 2 设置Vlan2生成树路径值为30 cost 30 Step 12 spanning-tree vlan 3 cost 30 Step 13 spanning-tree vlan 4 cost 30 Step 14 end Step 15 设置Vlan3生成树路径值为30 设置Vlan4生成树路径值为30 退出 在switch1的F0/2上重复9-11步骤设置VLAN8,9,10生成树路径值为30 退出 验证配置 保存配置 Step 16 exit Step 17 show running-config Step 18 copy running-config startup-config 配置Cluster
ZL-10th -Floor-1中的MAC地址为:000a.f404.ad80
ZL-10th -Floor-2中的MAC地址为:ZL-10th -Floor-3中的MAC地址为:000a.f404.ab80
ZL-10th -Floor-4中的MAC地址为:000a.f404.ac00
G0/1,132.107.77.74
ZL-10th -Floor-1 ZL-10th -Floor-2 ZL-10th -Floor-3
G0/1,132.107.77.75 Standby ip: 132.107.77.73
正在阅读:
思科2950交换机简明配置手册06-16
CommVault安装配置手册-Linux-Unix-Oracle篇10-24
2015年全国中考文言文比较阅读试题汇编01-09
奶奶的菜园作文700字06-26
浅谈我国公众参与失效的原因及其路径探究03-13
我的行囊作文800字02-05
nsn-Lte告警详解01-15
巧算24点比赛作文1200字07-10
最美的季节是春天作文800字06-20
仙人球作文400字06-25
- 什么叫借贷记账法?如何理解“借”和“贷”的含义?(出自第三单
- 小学三年级环境教育教案 山东科学技术出版社
- 高级财务会级课后练习及答案解析
- 井控技术管理复习题及答案
- 高传染病题目回忆
- 四群工作总结
- 2《除法的初步认识》示范说课稿讲解
- 《心理学导论(第二版)》黄希庭-练习题【全】
- 农村留守儿童心理健康教育的研究
- 中国生物医学工程学会
- 2型糖尿病中医药健康管理方案(1)
- 《提高学生的阅读与写作能力的研究》开题报告
- 曼昆_微观经济学_原理_第五版_课后习题答案
- 2011年作文练习:新材料作文审题立意
- 横山县榆林西南新区退房条件
- 最新固体制空调净化系统设计确认方案
- 药学综合考研之药物分析重点名词解释和问答题总结
- (2014年版)中国成人肾病综合征免疫抑制治疗专家共识
- 农信银竞赛答案
- 幼儿园家长工作计划秋(共12篇)