钢结构焊缝超声波探伤检验程序 中英文(T8mm)
更新时间:2024-03-16 22:57:01 阅读量: 综合文库 文档下载
编写: 作业指导书: 审核: 钢结构焊缝超声波探伤检验程序 审定: (T<8mm) 东莞市莱刚钢结构有限公司 批准: 1 文件编号: REV: 日期: 2007/10/01 页码: AWS D1.1: 2006, ASME SEC.V, JB/T4730.3-2005 参考文件: CS LJY GWQ HYM 1/10
作业指导书
(四)
Task Steering
(第一版 1nd edition)
编制:
审核:
批准:
执行日期:2007年10月20日
编写: 作业指导书: 审核: 钢结构焊缝超声波探伤检验程序 审定: (T<8mm) 东莞市莱刚钢结构有限公司 批准: 1 文件编号: REV: 日期: 2007/10/01 页码: AWS D1.1: 2006, ASME SEC.V, JB/T4730.3-2005 参考文件: CS LJY GWQ HYM 2/10 1、 简介General
1.1 本工艺旨在叙述薄板焊缝,如外板对接缝的超声波探伤(UT)方法。本工
艺介绍的方法目前在AWS D1.1中未详述,但在其它应用中被证明可行。 The workmanship is describled about welding seam of thin palte,such as method of UT to butt joint seam of external plate.This workmanship introduction is describled in AWS D1.1,but in other experiments are to be proved useful.
1.2 AWS D1.1:2006附录K通常用于板厚小于8mm的焊件的超声波检测。 AWS D1.1:2006 attach K usually do UT for less than 8mm thickness
weldment.
2、 工艺要求 Workmanship Requirement 2.1 用本工艺可检测的焊缝类型
The type of welding seam what this workmanship can inspect
使用埋弧焊(SAW),药芯焊丝气体保护焊(FCAW),气体保护钨极电弧焊(GTAW)或药皮焊条电弧焊(SMAW)焊接,两母材板厚相同的对接焊缝均可使用此工艺进行检测。其它焊缝形式须单独鉴定和单独的工艺。
This workmanship can inspect SAW,FCAW,GTAW or SMAW,butt joint seam of the same thickness of base material.Other welding seam must have individual inspect and workmanship. 2.2 可用于检测的设备类型
Equipment type of inspection
符合6.22.1(AWS D1.1:2006)要求的任何超声波检测设均可使用。如果有能力检测出试验样板的缺陷且达到本工艺要求时,可以使用其它设备,见2.6至2.11。
UT idetection device can be used in accordance with 6.22.1(AWS D1.1:2006).If other equipments can inspect limitation of trail sample plate and in accord with workmanship request,then allow to use.see 2.6—2.11 2.3 探头 Search unit
探头应符合6.22.6或6.22.7(AWS D1.1:2006)。
Search unit should be in accordance with 6.22.6 or 6.22.7(AWS D1.1:2006). 2.3.1 直(纵波)探头Straight(longitudinal wave) search unit
直(纵波)探头晶片有效面积不小于323mm2,也不要大于645mm2。探头可圆可方。探头应按6.29.1.3 1(AWS D1.1:2006)所述要进行三次反射。 The wafer effective area of straight(longitudinal wave) search unit should be between 323mm2 and 645mm2 .Either round or square is allowed to search unit.Search unit shall do three times reflect as 6.29.1.3 1(AWS D1.1:2006) requested.
2.3.2 斜探头 Inclined search unit
编写: 作业指导书: 审核: 钢结构焊缝超声波探伤检验程序 审定: (T<8mm) 东莞市莱刚钢结构有限公司 批准: 1 文件编号: REV: 日期: 2007/10/01 页码: AWS D1.1: 2006, ASME SEC.V, JB/T4730.3-2005 参考文件: CS LJY GWQ HYM 3/10 2.3.3
斜探头包括探头和入射角度。
Inclined search unit include search unit and incidence angle
2.3.2.1 频率 Frequency
探头频率应在2到6MHz之间,包括2和6MHz。
Search unit frequency shall between 2 and 6 MHz,include 2 and 6MHz.
2.3.2.2 探头尺寸 Search unit dimension
探头晶体外形可为正方形或矩形,宽度范围为15~25 mm,高度范围为15~25 mm。最大宽高比为1.2比1.1,最小宽高比为1.0比1.0。 The wafer externality of search unit shall be square or rectangle,width scope is 15~~25mm,height scope is 15~~25mm.The largest rate of width and height is 1.2:1.1,the smallest rate of width and height is 1.0:1.0.
2.3.2.3 探头角度 Search unit angle
探头角度在68到72度之间。
Search unit angle shall between 68 and 72 degree.
2.3.2.4 标记 Marking
每个探头应明确标记探头频率,理论反射角和入射点。入射点定位方法如6.29.2.1(AWS D1.1:2006)所述。
Each search unit shall mark search unit frequency,angle of reflection and points of incidence. The orientation method of points of incidence shall in accordance with 6.29.2.1(AWS D1.1:2006).
2.3.2.5 内部反射 Internal reflection
最大允许内部反射如6.24.3 1(AWS D1.1:2006)所述。
The biggest allowance of Internal reflection shall in accordance with 6.24.3 1(AWS D1.1:2006).
2.3.2.6 边缘距离 Edge distance.
探头尺寸是指从探头导入边缘到入射点之间的距离,它不超过25 mm。
Search unit dimension is from guide edge to points of incidence distance,less than 25mm.
2.3.2.7 IIW 块 ⅡW Sample
使用IIW标准块方法应符合6.29.2.6(AWS D1.1:2006),如图6.21(AWS D1.1:2006)所示。
The standard method of use ⅡW sample shall in accordance with 6.29.2.6(AWS D1.1:2006),see picture 6.21(AWS D1.1:2006).
2.3.2.8 附加校准块 Additional calibration block
要求有一个校准块,如下:
A calibration block is requested,see as follow:
2.3.2.8.1 接头结构 Search unit structure
编写: 作业指导书: 审核: 钢结构焊缝超声波探伤检验程序 审定: (T<8mm) 东莞市莱刚钢结构有限公司 批准: CS LJY GWQ HYM 文件编号: 参考文件: 2.3.2.8.2
2.3.2.8.3
2.3.2.8.4
2.3.2.8.5
2.3.2.8.6
REV: 1 日期: 2007/10/01 页码: 4/10 AWS D1.1: 2006, ASME SEC.V, JB/T4730.3-2005 只有坡口对接接头才能使用。
Bevel butt joint search unit can be only used. 材料类型 Material type
试验板材料须与实际焊接中使用的材料相同。
The material of sample plate shall be same as actual welding. 材料厚度 Material thickness
生产中检测的材料厚度应不大于试验样板的厚度。
Material thickness is needed to inspect that shall not thicker than sample plate during fabrication.
缺陷尺寸,方向和位置 limitation demision,direction and position 为可表示在生产焊缝中可能要出现的缺陷,试样应用标准块。此标准块包括一个直径为1.5 mm,平行于焊缝轴线,位于熔合区且贯穿试验板的通孔。见图1: 典型标准块位置。
In order to display limitation of welding that may be occurred,sample shall use standard one.There is a through hole in this standard sample,which shall be 1.5mm diameter,parallel welding seam axes,locate in fusion area and through sample plate. See picture 1:standard sample position
缺陷类型和位置 limitation type and position
在执行本工艺选择水平III时,标准块可存在其它类型缺陷。如有意识地让坡口焊缝未焊透,夹钨,焊缝塞入垫圈或螺母,或者其它能提供的与在实际生产中可能遇到的缺陷信号相同的方法。除了2.3.2.8.4条所指的钻孔外,包含缺陷的任何试验校准块应先进行射线探伤以确定缺陷尺寸、方位。画出标准块图与射线底片一起存档备案。
Technological choice in the implementation of the level III, the standard block may exist other types of defects. If so that the sense of groove weld lack of penetration, folder tungsten, insert washers or weld nut, or to provide other in the actual production may signal defects encountered the same way. Apart from the meaning of section 2.3.2.8.4 bored, contains flawed calibration block any trial should be conducted to determine the defect-detection size, position. Standard block map drawn-ray film archive with the record. 校准严禁使用角落反射。
Forbideen using corner inflection when adjustment
编写: 作业指导书: 审核: 钢结构焊缝超声波探伤检验程序 审定: (T<8mm) 东莞市莱刚钢结构有限公司 批准: 1 文件编号: REV: 日期: 2007/10/01 页码: AWS D1.1: 2006, ASME SEC.V, JB/T4730.3-2005 参考文件: CS LJY GWQ HYM 5/10 通孔板宽应满足到焊缝每侧应有2个扫描距离。通孔图 1 2.4
探伤表面处理 Testing surface treatment
被探焊缝表面及相邻区域应用砂轮磨干净或用钢丝刷刷干净到允许超声波畅通无阻进入母材的程度。被探表面最少应如标准块般光洁。
The welding seam surface and adjacent area shall be cleaned by grinding wheel and wire brush,make sure that the ultrasonic can enter into base material unlocked.The glabrous of inspected surface shall be same as standard sample . 2.5 耦合剂 Couplant
在被探材料与探头之间应使用耦合剂。可以使用甘油或纤维胶与水按比例混合作为耦合剂。如果必要,可使用湿的添加剂。标准块可以用轻机油作为耦合剂。
Couplant shall be used between inspected material and search unit.Couplant can mix with glycerin or “viscose and water”.If necessary, wet additive is allowed to use.Standard sample can use light machine oil as couplant. 2.6 设备要求 Equipment requirement
采用适当的A型显示脉冲反射式超声波探伤仪,工作频率为1~6MHz。 A type vision impluse reflection ultrasonic fault detector is properly used,working frequency is 1~~6MHz. 2.6.1 水平线性 Horizontal linearity
探伤仪的水平线性应在用于检测的全声程距离内进行认证,应与6.30.1(AWS D1.1:2006)一致。
Horizontal linearity of flaw detector shall be checked in sound path distance,and shall be in accordance with 6.30.1(AWS D1.1:2006).
2.6.2 探伤仪要求Flaw detector requirement
正在阅读:
人事处下发文件目录01-04
2018年尔雅中华诗词之美课后答案10-10
青门老圃传阅读答案10-05
浅析我国商业银行信贷风险管理的现状及对策05-01
空压机知识及空压机维修04-04
高层建筑结构发展趋势01-06
食品用纸包装生产许可实施细则 - 图文04-30
- 多层物业服务方案
- (审判实务)习惯法与少数民族地区民间纠纷解决问题(孙 潋)
- 人教版新课标六年级下册语文全册教案
- 词语打卡
- photoshop实习报告
- 钢结构设计原理综合测试2
- 2014年期末练习题
- 高中数学中的逆向思维解题方法探讨
- 名师原创 全国通用2014-2015学年高二寒假作业 政治(一)Word版
- 北航《建筑结构检测鉴定与加固》在线作业三
- XX县卫生监督所工程建设项目可行性研究报告
- 小学四年级观察作文经典评语
- 浅谈110KV变电站电气一次设计-程泉焱(1)
- 安全员考试题库
- 国家电网公司变电运维管理规定(试行)
- 义务教育课程标准稿征求意见提纲
- 教学秘书面试技巧
- 钢结构工程施工组织设计
- 水利工程概论论文
- 09届九年级数学第四次模拟试卷
- 焊缝
- 探伤
- 钢结构
- 超声波
- 中英文
- 检验
- 程序
- T8mm
- 电力电子与电气传动综合课程设计
- 《论语》读书心得
- TN - HDB - 0005 - R语言与HANA建模 (一)HANA与Rserve的连接及
- 2015电子科技大学 - 图论期末考试复习题
- 福师《现代远程学习概论》在线作业及答案
- 如何处理好大学校园宿舍人际关系
- 人教版初一上册语文第四单元同步测试题(有答案)
- 幼儿园建构式课程中班(上)主题六活动预设
- 民间游戏在幼儿园教育活动中的应用研究
- 周三多管理学题库,共41页
- 杭州西溪国家湿地公园旅游规划计划书
- 广西工学院鹿山学院关于开展班级“创优争先”活动实施方案1101
- 基坑排水、临边防护方案
- K12九年级英语全册 Unit 7 Lesson 42 Peace at Last教
- 国庆大阅兵观后感
- 2019-2020年高考数学二轮复习第1部分重点强化专题专题4立体几何
- 会计专业毕业论文选题题目
- 技术资料档案管理制度
- 河北省2016年上半年综合法律知识:职务侵占罪考试试卷
- 土建施工员实务练习题答案5.11