DD24S3.3-14000中文资料

2:1 Wide Input Voltage Range

FEATURES

● Single Output Up to 14A ● High Efficiency up to 91% ● RoHS Directive Compliant ● Fixed Switching Frequency ● No Minimum Load Required ● Six-Sided Continuous Shield ● 2:1 Wide Input Voltage Range ● Approved for Basic Insulation ● 60 Watts Maximum Output power ● Standard 2.02” x 2.02” x 0.4” Package

UL TUV CB

CE MARK (Pending)

SPECIFICATIONS:

DD Series

All specifications apply @ 25°C ambient unless otherwise noted

INPUT SPECIFICATIONS

PROTECTION SPECIFICATIONS

Over Voltage Protection.....................3.3V Output....................3.7V - 5.4V (Ctrl. voltage clamp) 5V Output.......................5.6V - 7.0V 12V Output.................13.5V - 19.6V 15V Output.................16.8V - 20.5V

Input Voltage Range............24V nominal input......................18 - 36VDC

48V nominal input......................36 - 75VDC

Under Voltage Lockout

24V nominal input...........DC-DC ON..................................17VDC typ. DC-DC OFF................................15VDC typ.

48V nominal input...........DC-DC ON..................................34VDC typ. DC-DC OFF................................32VDC typ.

Over Load Protection (% of FL at nominal input).......................150% max.

Short Circuit Protection......................................Hiccup, automatic recovery

Input Filter.......................................................................................Pi Type

Over Temperature Protection.......................................................110°C typ.

Input Voltage Variation.........dv/dt............................................5V/ms max (Complies with ETS300 132 part 4.4)

GENERAL SPECIFICATIONS

Efficiency........................................................................................see table

Input Surge Voltage (100ms max)...............24V input...................50VDC Switching Frequency.................................................................300KHz typ.

48V input.................100VDC

Isolation Voltage (Input to Output).........................................1600VDC min.

Input Reflected Ripple Current (nominal Vin and FL)...................20mAp-p Isolation Voltage (Input to Case)...........................................1600VDC min.

Start Up Time (nominal Vin and constant resistive load)

Isolation Voltage (Output to Case)........................................1600VDC min. Power Up..............................................................................20ms max.

Remote ON/OFF..................................................................20ms max. Case Grounding (connect case to -Vin with decoupling Y cap) ...........TBD

Remote ON/OFF (See Note 2)

Positive Logic ................DC-DC ON................Open or 3V < Vr < 12V DC-DC OFF.............Short or 0V < Vr < 1.2V

Negative Logic ...............DC-DC ON...............Short or 0V < Vr < 1.2V DC-DC OFF..............Open or 3V < Vr < 12V

Isolation Resistance...............................................................10 ohms min. Isolation Capacitance............................................................. 1500pF max.

9

ENVIRONMENTAL SPECIFICATIONS

Remote Off Input Current (nominal Vin)..............................................3mA

Operating Ambient Temperature.............-40°C to +50°C (without derating) +50°C to +105°C (with derating)

OUTPUT SPECIFICATIONS

Storage Temperature..........................................................-55°C ~ +125°C

Output Voltage..............................................................................see table

Maximum Case Temperature...........................................................+105°C

Voltage Accuracy (nom Vin and full load)........................................... ±1%

Relative Humidity...................................................................5% to 95% RH

Voltage Adjustability (See Note 1).....................................................±10%

Temperature Coefficient...................................................±0.02% / °C max.

Output Current..............................................................................see table

Output Power........................................................................60 watts max.

Thermal Impedance (See Note 4) Without Heat-Sink..............................................................9.2°C / Watt With Heat-Sink.....................................................................7.6°C/Watt

Line Regulation (LL to HL at FL).......................................................±0.2%

Thermal Shock.................................................................... MIL-STD-810D

Load Regulation (no load to 100% load)...........................................±0.5%

Vibration................................10~55Hz, 10G, 30 minutes along X, Y, and Z

Minimum Load.....................................................................................0mA

Output Ripple & Noise..................................................................see table

MTBF (See Note 3)........Bellcore TR-NWT-000332............1.093 x 10 hrs

5

MIL-STD-217F.............................1.096 x 10 hrs

6

Transient Response Recovery Time (25% load step change)...........250us

2:1 Wide Input Voltage Range

SPECIFICATIONS (CONTINUED)

All specifications apply @ 25°C ambient unless otherwise noted

PHYSICAL SPECIFICATIONS

(See Note 5) SAFETY & EMC

Approvals and Standards..................IEC60950-1, UL60950-1, EN60950-1

Weight....................................................................................60g (2.11 oz)

Dimensions................. 2.02 x 2.02 x 0.40 inches (51.3 x 51.3 x 10.2 mm)

Conducted Emissions.................EN55022......................................Class A

Case Material............................................................Nickel-coated copper

Radiated Emissions....................EN55022......................................Class A

Base Material....................................................Non-conductive black FR4

ESD............................................EN61000-4-2.....................Perf. Criteria B

Potting material................................................................Epoxy (UL94-V0)

Radiated Immunity......................EN61000-4-3.....................Perf. Criteria A

Shielding....................................................................................six – sided

Fast Transient.............................EN61000-4-4.....................Perf. Criteria B

Surge..........................................EN61000-4-5.....................Perf. Criteria B

Conducted Immunity...................EN61000-4-6.................... Perf. Criteria A

Due to advances in technology, specifications subject to change without notice

OUTPUT VOLTAGE / CURRENT RATING CHART

Model Number DD24S3.3-14000 DD24S5-12000 DD24S12-5000 DD24S15-4000 DD48S3.3-14000 DD48S5-12000 DD48S12-5000 DD48S15-4000

48VDC

Input Range

Output Voltage

Output Current Min. LoadFull LoadOutput Ripple & Noise

Input Current (8)Max Capacitive

(9)Efficiency Load No loadFull Load3.3 VDC

24VDC

75mVp-p 100mVp-p 100mVp-p 75mVp-p 75mVp-p 100mVp-p 100mVp-p

5 VDC 12 VDC 15 VDC 3.3 VDC 5 VDC 12 VDC 15 VDC

0mA 0mA 0mA

0mA

12,000mA5000mA 4000mA

14,000mA

90mA

1132mA

91% 90% 90%

89%

20,400µF 3550µF 2300µF 36,000µF 20,400µF 3550µF 2300µF

(18 – 36 VDC)

0mA 0mA 0mA

12,000mA5000mA 4000mA

100mA 100mA 100mA

1437mA 1453mA 1453mA

91% 90% 90%

(36 – 75 VDC)

NOTES

1. Maximum output deviation is 10% inclusive of remote sense and trim. If remote sense is not being used, the +sense should be

connected to its corresponding +OUTPUT and likewise the -sense should be connected to its corresponding –OUTPUT.

2. The ON/OFF control function: There are positive (standard) and negative logic (option). The pin voltage is referenced to negative input. To order negative logic ON/OFF control add the suffix “R” to the part number (Ex: DD48S5-12000R)

3. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40ºC. (Ground fixed and controlled environment). MIL-STD-217F Notice2 @ Ta=25°C, Full Load (Ground, Benign, controlled environment).

4. Heat sink is optional. Please call factory for ordering details.

5. The DD series required an external filter to meet EN55022 class A. (TBD)

6. Typical Value at nominal input voltage.

7. Maximum value at nominal input voltage and full load

8. Typical Value at nominal input voltage and full load.

9. Test by minimum Vin and constant resistive load.

2:1 Wide Input Voltage Range

DERATING CURVES & EFFICIENCY GRAPHS

MECHANICAL DRAWING

PIN CONNECTION

EXTERNAL OUTPUT TRIMMING

Output can be externally trimmed by using the method shown below.

1. All dimensions in inches (mm) Tolerance: X.XX±0.02 (X.X±0.5)

2. Pin pitch tolerance ±0.014 (0.35)

本文来源：https://www.bwwdw.com/article/jsfj.html