HDMI-Compliance-Test-Software-Datasheet

HDMI compliance test software

Option HDM, Option HDM-DS, Option HT3, Option HT3-DS Datasheet

Option HDM and HDM-DS Advanced Analysis and Compliance Softwareautomates a comprehensive range of tests as per CTS 2.0. TDSHT3 andHT3-DS HDMI Compliance Test Software automate a comprehensiverange of tests as per CTS 1.4b - enabling unprecedented efficiency withreliable results. HDMI 1.4b compliance testing is a PREREQUISITE forHDMI 2.0 testing.

Key features

Conformance to HDMI 2.0 Compliance Test Specification (CTS)Introducing the innovative HDMI protocol analyzer solution for HDMI1.4b

One-box solution for HDMI 1.4b physical-layer and protocol-layertesting

Fast, efficient direct synthesis solution

Conformance to HDMI 1.4a/b Standards and Compliance TestSpecification 1.4a/b (CTS)

Complete validation to standards with wide range of tests for source,sink, and cable devices

Accurate source tests using precise measurement techniquesDependable sink tests with closed-loop measurements that eliminatenonlinearities in test setup

Automation of complex sink and cable tests with remote control ofsignal sources and software emulation of cable effects, eliminating theneed for hardware transition time converters (TTC) and cableemulators

Quick results with automatic mask fit, measurements and Pass/Failnotification, and in-depth results with statistical analysis and maskmargins

Quick testing with one-button selection of multiple tests and CSV-format test summary and reports

HDMI compliance test software

Engineers designing and validating the HDMI physical layer of their devicesface constant pressure to improve efficiency. Designers need to perform awide range of compliance tests quickly and reliably right on their bench.HDMI 2.0 supports features like 2160p (also known as Ultra HD/4K 2K60/50 Hz), operating at 5.94 Gcps apart from 4K 2K 4:2:0, using the sameCat 2 cable and HDMI 1.4b connector. HDMI 1.4a/b introduces AutomotiveHDMI (Type E) in addition to Mobile HDMI (Type D), HEAC, 3D HDMI, 4K ×2K patterns, and new Calorimetric patterns, all operating up to 3.4 Gb/s.

Comprehensive HDMI 2.0/1.4a/b solution including test fixtures, DPO/DSA/MSO70000 real-time oscilloscopes, P7313SMA differential

probes, AWG70000/7000 signal sources, HDMI fixtures, and DSA8300sampling oscilloscopes

Applications

Design and validation of HDMI 2.0/1.4a/b physical layer

Datasheet

Reliable and dependable results

Option HDM embeds HDMI forum CTS 2.0 compliance test procedures,ensuring reliable results. TDSHT3 embeds the HDMI CTS 1.4a/bcompliance test procedures, including the software clock recovery(SoftCRU), ensuring dependable results. Accurate eye rendering and

precise violation testing deliver credible results. Perform accurate Sink testswith closed-loop measurements that eliminate nonlinearities of the testsetup. Authentic measurement techniques and automation eliminate errorsto provide repeatable results.

Faster validation cycles

The unparalleled automation offered on the HDM, HDM-DS, TDSHT3 andHT3-DS enables faster validation. Reduce test times for complete HDMISink testing with HDM, HDM-DS, TDSHT3 and HT3-DS by digitally

controlling cable emulator and TTC effects allowing for a single hardwareconnection for all resolutions. Demonstrate efficiency by using the "SelectAll" feature to perform multiple tests. Quickly generate CSV-format

summaries or detailed reports at a press of a button.

HDM-DS SW - Sink Test

HDM SW - Source Test

HDM-DS SW - Sink Protocol Test

HT3-DS software

HDMI Compliance Test Software - HDM, HDM-DS, HT3, HT3-DS

Test descriptions

TEK-PGY-HDMI-PA-SW

Tektronix is pleased to introduce the HDMI protocol analyzer softwaredeveloped by our third-party partner for our DPO/DSA/MSO70000B/C/DSeries real-time oscilloscopes with bandwidth ≥12.5 GHz and above.Salient features include:

One-box solution for both HDMI physical- and protocol-layer testingleveraging real-time oscilloscopes.

Detailed HDMI protocol decodes. Multi-view decode capability:Bus viewerFrame viewerEvent viewerData packet viewerProtocol viewer

Seamless link layer to physical layer analysis and decode capability:Ability to view analog waveform with protocol decode

Common probing technique for physical-layer and protocol-layertesting.

Refer to the Prodigy techno visions website (http://

) for more details on the HDMI protocol analyzersoftware.

1

Requires record length of more than 16M on each channel. HDMI 2.0 Eye Diagram is at TP2 after cable emulator effect.

Datasheet

HDMI Protocol Tests (as per CTS 1.4a/b)

Source protocol tests:

7-16 legal codes7-17 basic protocol7-18 extended control period7-19 packet types7-23/7-24 pixel encoding7-25 video format timing7-26 pixel reception7-27 AVI info frameSource audio:

7-28 IEC 60958/IEC 61937 7-29 ACR

7-30 audio sample packet jitter7-31 audio info frame

7-32 audio sample packet interoperability7-33 source interoperability with DVISource advanced features:

7-34 deep color

7-35 gamut metadata transmission7-36 high bit rate audio7-37 one-bit audio7-38 3D video format timing

7-39 4KX2K video format timing – record length dependent7-40 extended colorimetry transmission

MHL protocol compliance tests (as per CTS1.1)

Source Protocol Tests:

Legal CodesBasic ProtocolPacket TypesSource VideoPixel EncodingVideo Format TimingVideo Quantization TestAVI Info FrameSource Audio Tests:

Audio Test

Audio Clock Regeneration TestAudio Info Frame

Supported Tektronix instruments

Real-time oscilloscopes

DPO/DSA/MSO70000 series real-time oscilloscopes support HDM,HDM-DS, HT3, HT3-DS, DPOFL-HDM and DPOFL-HDM-DSNote: The recommended oscilloscope bandwidth for HDMI 2.0 is

≥16 GHz. Although a 12.5 GHz bandwidth oscilloscope is supported, itwill have as much as a 10% inaccuracy in test results.Sampling oscilloscopes

TDR tests: DSA8300 oscilloscope with 80E03 and 80E04 modulesGenerators (using direct synthesis method)

AWG70002A with Opt. 02, Opt. 225 and Opt. 03 (sequencing option)(Qty: 2), or AWG7122B/C with Opt. 01, Opt. 02/06 and Opt. 08 (Qty: 2)AFG3102/C or AFG3252/C - Used for synchronizing and triggering the2 AWGs in the direct synthesis setup

Combined HDMI and MHL protocol solution

We are also pleased to announce the availability of the combined HDMIand MHL protocol analyzer software to enable customers who work on boththe technologies to leverage a cost-effective protocol software bundle. Fordetails on MHL protocol analyzer software refer to MSR#1992010. Thebundled HDMI/MHL protocol analyzer software is a stand-alone option forthe Tektronix real-time oscilloscopes with the following nomenclature: TEK-PGY-HDMH-PA-SW.

HDMI Compliance Test Software - HDM, HDM-DS, HT3, HT3-DS

Ordering information

HDM test software

Test software includes:

Application CD, HDMI direct synthesis AWG patterns DVDs, and electronic documentation.

Software options

To order with oscilloscope

Product/featureOption HDM

Description

HDMI 2.0 Advanced Analysis and Compliance Software for Source testing.(Prerequisite for HDMI 2.0 is HDMI 1.4b testing; hence HT3 is required.

Prerequisite is Option DJA, Opt 10XL (required for 100M RL), Opt SR-EMBD andSR-CUST).

HDMI 2.0 Advanced Analysis and Compliance Software for Sink testing

(Prerequisite HDM and HT3-DS). Since HDMI 1.4b is a prerequisite for HDMI2.0 testing, HT3-DS is needed.HDMI 1.4b Compliance Test Software

HDMI 1.4b Direct Synthesis Software (requires Opt. HT3)

HDMI 1.4b - only Protocol Analyzer Software (requires Option 20XL and (4)P7313SMA probes)

Combined HDMI 1.4b and MHL Protocol Analyzer Software (requires Option 20XL,and (4) P7313SMA probes for HDMI protocol testing or (2) P7313SMA and (1)P7240 probes for MHL protocol testing)

Advanced Analysis and Compliance Software for HDMI 2.0 Tx floating licenseAdvanced Analysis and Compliance Software for HDMI 2.0 Rx floating licenseAdvanced Analysis and Compliance Software for HDMI 2.0 Tx floating license (trialversion)

Advanced Analysis and Compliance Software for HDMI 2.0 Rx floating license (trialversion)

Option HDM-DS

Option HT3Option HT3-DSTEK-PGY-HDMI-PA-SWTEK-PGY-HDMH-PA-SW

DPOFL-HDMDPOFL-HDM DSDPOFT-HDMDPOFT-HDM DS

Software upgrades

To upgrade an existing oscilloscope

Product/featureDPO/DSA/MSO70000DPO/DSA/MSO70000DPO/DSA/MSO70000DPO/DSA/MSO70000TEK-PGY-HDMI-PA-SWTEK-PGY-HDMH-PA-SW

Description

Order DPO-UP – Opt. HDMOrder DPO-UP – Opt. HDM-DSOrder DPO-UP – Opt. HT3Order DPO-UP – Opt. HT3-DS 2

HDMI-only Protocol Analyzer Software (requires Option 20XL and (4) P7313SMAprobes)

Combined HDMI and MHL Protocol Analyzer Software (requires Option 20XL, and(4) P7313SMA probes for HDMI protocol testing or (2) P7313SMA and (1) P7240probes for MHL protocol testing)

Note: The recommended oscilloscope bandwidth for performing both physical-layer and protocol-layer testing using the same oscilloscope is ≥12.5 GHz, as the protocolanalyzer software requires the 20XL record length option.

2

HT3-DS is available on DPO/DSA/MSO70000 series scopes with bandwidth greater than 8 GHz.

Datasheet

Recommended equipment and accessories

AccessoryOscilloscope

Description

16M Record Length / Ch or more - Opt. 2XL on DPO/DSA/MSO70000oscilloscopes (for eye diagram and jitter tests)

250M Record Length / Ch - Opt. 20XL on DPO/DSA/MSO70000 oscilloscopes (forprotocol analysis)

100M Record Length Opt 10XL (needed for HDMI 2.0)

Option DJA, Opt SR-EMBD and SR-CUST (also needed as a pre-requisite for HDMSoftware)

AWG70002A with opt 01, 03 and 225 or AWG7122B/C with option 01, 02/06, and08 (for direct synthesis method)

P7350SMA (2 probes required) - for testing TMDS clock rates less than or equal to74.25 MHz

Minimum two P7313SMA probes are required for testing all resolutions of HDMI1.4a/b testing, and are also used for single-ended testing.

Minimum 3 probes are recommended for HDMI 2.0 testing and are also used forsingle-ended testing.

Four P7313SMA probes are recommended for faster physical layer testing of all4 HDMI 1.4 and HDMI 2.0 channels.

Four P7313SMA probes are required for protocol analysis.

P7240 used with old 1.2 test fixtures (2 probes required); P7313SMA probes canalso be used to test single-ended tests using 50 short.PPM100 flexible arm probe positioner

Consists of:

Matched SMA cables (174-4944-xx) (Qty: 10)BNC cables (012-0057-xx) (Qty: 4)BNC-T adapter (015-1016-xx) (Qty: 1)

Bias tees from Mini-Circuits (ZX85-12G-S+) (Qty: 8)

TTC filter from Picosecond pulse labs (5915-110-120PS) (Qty: 8)GPIB cables from NI (763061-xx)

6 dB attenuator from Mini-Circuits (BW-S6W2+) (Qty: 8)

PWS4205 for providing bias voltage during Sink testing or optionally powering thefixture during source testing

Delay line for introducing 112 ps skew from SPECTRUM (8001-SM21-02) (Qty: 6)Delay line for introducing 0.15 Tbit skew from Carlisle Interconnect Technologies(5018CCSF, SMA (M) to (F))(Qty: 6)

50 ohm male terminations (015-1022-01) - (Qty: 6)50 ohm female terminations (015-1004-01) - (Qty: 2)

50 ohm SMA cable, 1 M length from HUBER+SUHNER SUCOFLEX (104PE) -(Qty: 2)

Available, please contact Tektronix Local Representative for more B-to-GPIB controller (with driver software)Ethernet GPIB controller (with driver software)

Signal sourcesProbes

Differential probes

Active probesProbe positioner

HDMI direct synthesis accessory kit (required with Option HT3-DS and OptionHDM-DS)

External power supply

Additional recommended accessories for HDMI 2.0

Additional recommended accessories for impedance test

HDMI 2.0 FixtureSink test automation 3NI GPIB-USB-A/BNI GPIB-ENET/100

3

For ordering, contact National Instruments ().

HDMI Compliance Test Software - HDM, HDM-DS, HT3, HT3-DS

HDMI 1.4b type A fixtures

TF-HDMI-TPA-S Test Adapter Set (used for Source, Sink, and Cable test) includes the following:

TF-HDMI-TPA-P plug fixture

TF-HDMI-TPA-CE EDID board with EDID EEPROM

TF-HDMI-TPA-STX Test Adapter Set (used for Source and Sink test) includes the following:

TF-HDMI-TPA-P plug fixture

TF-HDMI-TPA-R receptacle fixtures (Qty: 2)Calibration fixture

TF-HDMI-TPA-CE EDID board with EDID EEPROM

HDMI 1.4b type C fixtures

TF-HDMIC-TPA-S Test Adapter Set (used for Source, Sink, and Cable testing) includes the following:

TF-HDMIC-TPA-P plug fixture

TF-HDMIC-TPA-R receptacle fixtures (Qty. 2)Calibration fixture

TF-HDMI-TPA-CE EDID board with EDID EEPROM

TF-HDMIC-TPA-STX Test Adapter Set (used for Source testing only) includes the following:

TF-HDMIC-TPA-P plug fixture

TF-HDMI-TPA-CE EDID board with EDID EEPROM

HDMI 1.4b type D fixtures

TF-HDMID-TPA-P Plug BoardTF-HDMID-TPA-R Receptacle Board

TF-HDMI-TPA-CE consisting of (to be ordered separately):

EDID Fixture PCBA

EEPROM with HDMI 1.4a/b SoftwareRibbon Cable (174-5746-xx)Customer Documentation

HDMI 1.4b type E fixtures

TF-HDMIE-TPA-KIT Test Adapter Kit (used for Source, Sink, and Cable testing) includes the following:

1 TF-HDMIE-TPA-P plug board2 TF-HDMIE-TPA-R receptacle boards

TF-HDMI-TPA-CE consisting of (to be ordered separately):

EDID Fixture PCBA

EEPROM with HDMI 1.4a/b SoftwareRibbon Cable (174-5746-xx)Customer Documentation

Datasheet

TF-HDMI-TPA-STX

TF-HDMID-TPA-P/R

TF-HDMI-TPA-T

HDMI Compliance Test Software - HDM, HDM-DS, HT3, HT3-DS

Tf-HDMIE-TPA-KIT

Tektronix is registered to ISO 9001 and ISO 14001 by SRI Quality System Registrar.

Product(s) complies with IEEE Standard 488.1-1987, RS-232-C, and with Tektronix Standard Codes and Formats.

Datasheet

ASEAN / Australasia (65) 6356 3900 Belgium 00800 2255 4835*

Central East Europe and the Baltics +41 52 675 3777 Finland +41 52 675 3777 Hong Kong 400 820 5835 Japan 81 (3) 6714 3010

Middle East, Asia, and North Africa +41 52 675 3777 People's Republic of China 400 820 5835 Republic of Korea 001 800 8255 2835 Spain 00800 2255 4835*Taiwan 886 (2) 2722 9622

* European toll-free number. If not accessible, call: +41 52 675 3777

Austria 00800 2255 4835*Brazil +55 (11) 3759 7627

Central Europe & Greece +41 52 675 3777 France 00800 2255 4835*India 000 800 650 1835

Luxembourg +41 52 675 3777 The Netherlands 00800 2255 4835*Poland +41 52 675 3777

Russia & CIS +7 (495) 6647564 Sweden 00800 2255 4835*

United Kingdom & Ireland 00800 2255 4835*Balkans, Israel, South Africa and other ISE Countries +41 52 675 3777 Canada 1 800 833 9200 Denmark +45 80 88 1401 Germany 00800 2255 4835*Italy 00800 2255 4835*

Mexico, Central/South America & Caribbean 52 (55) 56 04 50 90 Norway 800 16098 Portugal 80 08 12370

South Africa +41 52 675 3777 Switzerland 00800 2255 4835*USA 1 800 833 9200

Updated 10 April 2013

For Further Information. Tektronix maintains a comprehensive, constantly expanding collection of application notes, technical briefs and other resources to help engineers working on the cutting edge of technology. Please visit .Copyright © Tektronix, Inc. All rights reserved. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specification and

price change privileges reserved. TEKTRONIX and TEK are registered trademarks of Tektronix, Inc. All other trade names referenced are the service marks, trademarks, or registered trademarks of their respective companies.

04 Dec 2014 61W-28296-1

本文来源：https://www.bwwdw.com/article/jhf1.html