83B1A-A12-K06L中文资料
更新时间:2023-05-10 17:02:01 阅读量: 实用文档 文档下载
Standard Resistance Range...................................................................200 to 100 K ohms......................................1 K to 100 K ohmsTotal Resistance Tolerance.....................................................................±5 %............................................................±10 %Independent Linearity.............................................................................±0.25 %.......................................................±0.25 %Absolute Minimum Resistance (J Taper)................................................1.0 ohm or 0.1 % (whichever is greater).....–
Effective Electrical Angle........................................................................3600 ° +10 °, -0 °.........................................3600 ° +10 °, -0 °Dielectric Withstanding Voltage (MIL-STD-202, Method 301)
Sea Level............................................................................................1,000 VAC minimum....................................1,000 VAC minimum
Insulation Resistance (500 VDC)............................................................1,000 megohms minimum...........................1,000 megohms minimumPower Rating (Voltage Limited By Power Dissipation or 350 VAC, Whichever Is Less)
+70 °C ...............................................................................................1 watt...........................................................1 watts+125 °C..............................................................................................0 watt...........................................................0 watt
Theoretical Resolution............................................................................See table.....................................................Essentially infinite
End Voltage (K Taper).............................................................................–...................................................................0.2 % of applied voltageNoise (J Taper)........................................................................................100 ohms ENR maximum............................–
Output Smoothness (K Taper)................................................................–...................................................................0.15 % maximum
Environmental Characteristics1
Operating Temperature Range...............................................................+1 °C to +125 °C.........................................+1 °C to +125 °CStorage Temperature Range...................................................................-55 °C to +125 °C........................................-55 °C to +125 °CTemperature Coefficient Over Storage Temperature Range...................±50 ppm/°C.................................................±100 ppm/°CVibration..................................................................................................15 G.............................................................15 GTotal Resistance Shift.........................................................................±2 %............................................................±2 %Voltage Ratio Shift..............................................................................±0.2 %.........................................................±0.2 %
Wiper Bounce.....................................................................................0.1 millisecond maximum............................0.1 millisecond maximumShock......................................................................................................50 G.............................................................50 GTotal Resistance Shift.........................................................................±2 %............................................................±2 %Voltage Ratio Shift..............................................................................±0.2 %.........................................................±0.2 %
Wiper Bounce.....................................................................................0.1 millisecond maximum............................0.1 millisecond maximumLoad Life.................................................................................................1,000 hours.................................................1,000 hoursTotal Resistance Shift.........................................................................±2 % maximum...........................................±5 % maximum
Rotational Life (No Load)........................................................................1,000,000 shaft revolutions.........................4,000,000 shaft revolutionsTotal Resistance Shift.........................................................................±5 % maximum ..........................................±5 % maximumMoisture Resistance (MIL-STD-202, Method 103, Condition B)
Total Resistance Shift.........................................................................±2 % maximum...........................................±5 % maximum
Insulation Resistance (500 VDC)........................................................100 megohms minimum..............................100 megohms minimumIP Rating.................................................................................................IP 40............................................................IP 40
Mechanical Characteristics1
Stop Strength......................................................................................................................................................................33.90 N-cm (48.0 oz.-in.) minimumMechanical Angle............................................................................................................................................................................................3600 ° +15 °, -0 °Torque
Starting................................................................................................................................................Running torque plus 0.7 N-cm (1.0 oz.-in.) maximumRunning (1 or 2 Section)..............................................................................................................................................0.18 to 1.41 N-cm (0.25 to 2.0 oz.-in.)Mounting (Torque on Bushing)......................................................................................................................................1.7-2.0 N-m (15-18 lb.-in.) maximumShaft Runout........................................................................................................................................................................................0.15 mm (0.006 in.) T.I.R.Shaft End Play......................................................................................................................................................................................0.36 mm (0.014 in.) T.I.R.Shaft Radial Play..................................................................................................................................................................................0.13 mm (0.005 in.) T.I.R.Weight (Single Section)......................................................................................................................................................................................21 gm (0.75 oz.)(Each Additional Section)..............................................................................................................................................................................18 gm (0.65 oz.)Terminals........................................................................................................................................................................Printed circuit terminals or solder lugsSoldering Condition......................................................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ” wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux
Marking..........................................................................Manufacturer’s trademark, wiring diagram, date code and resistance, manufacturer’s part numberGanging (Multiple Section Potentiometers)......................................................................................................................................................2 cup maximumHardware............................................One lockwasher and one mounting nut is shipped with each potentiometer, except where noted in the part number.
NOTE: MODEL 83/84 PERFORMANCE SPECIFICATIONS DO NOT APPLY TO UNITS SUBJECTED TO PRINTED CIRCUIT BOARD CLEANING PROCEDURES.1
AT ROOM AMBIENT: +25 °C NOMINAL AND 50 % RELATIVE HUMIDITY NOMINAL, EXCEPT AS NOTED.
*RoHS Directive 2002/95/EC Jan 27 2003 including Annex
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
83/84 - 5/8 ” Square 10-Turn
Wirewound Resolution Table
Resistance(Ohms)2005001 K2 K5 K10 K20 K50 K100 K
Resolution(Nom.) (%)
.048.037.032.031.023.020.015.012.010
Dimensional Drawings
Dual Section Model 84 Solder Lugs
Dual Section Model 83 PC Pins
Note: The Models 83/84 dimensions for dualsection assembly are for either single or dualconcentric shaft styles.
MM(INCHES)
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
83/84 - 5/8 ” Square 10-Turn
Product Dimensions
NOTE: "D" OPTION - NO A/R LUG. OTHER LOCATING LUG OPTIONS AVAILABLE. FOR DETAILS CONSULT FACTORY.
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
83/84 - 5/8 ” Square 10-Turn
How to Order
REV. 08/11/06
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
正在阅读:
83B1A-A12-K06L中文资料05-10
高三地理六大类简答题专项训练 10-19
XX军事理论课心得体会12-31
大朱少先队红旗大队申报材料03-29
精装修施工方案(改)04-28
学习岁儿童学习与发展指南心得体会04-30
2018南通市中考英语试卷(含答案)11-06
参观渡江纪念碑作文500字07-10
铁路桥下防护栅栏预制交底 - 图文03-22
xx镇xxxx年工作计划范文参考08-12
- 教学能力大赛决赛获奖-教学实施报告-(完整图文版)
- 互联网+数据中心行业分析报告
- 2017上海杨浦区高三一模数学试题及答案
- 招商部差旅接待管理制度(4-25)
- 学生游玩安全注意事项
- 学生信息管理系统(文档模板供参考)
- 叉车门架有限元分析及系统设计
- 2014帮助残疾人志愿者服务情况记录
- 叶绿体中色素的提取和分离实验
- 中国食物成分表2020年最新权威完整改进版
- 推动国土资源领域生态文明建设
- 给水管道冲洗和消毒记录
- 计算机软件专业自我评价
- 高中数学必修1-5知识点归纳
- 2018-2022年中国第五代移动通信技术(5G)产业深度分析及发展前景研究报告发展趋势(目录)
- 生产车间巡查制度
- 2018版中国光热发电行业深度研究报告目录
- (通用)2019年中考数学总复习 第一章 第四节 数的开方与二次根式课件
- 2017_2018学年高中语文第二单元第4课说数课件粤教版
- 上市新药Lumateperone(卢美哌隆)合成检索总结报告
- 中文
- 资料
- 83
- 12
- 06
- 公文写作格式规范及范文
- 幼儿园大班上学期语文期末试卷
- 1外国美术史完整哦哦
- Ansys Workbench 11.0 参数化管理
- 女学生读中专技校学啥好
- 二年级下册语文期末考试试题4
- 保健之足底按摩【附足底穴位图】
- 柿子树夏季修剪方法
- 一年级小学生春节作文范文八篇
- 对网络教育与传统教育的思考
- 保先教育个人整改措施
- 高考化学常见官能团的性质和同分异构体(学生)
- 健康源自纯净 金利源开创全屋净水时代
- 牙周病的危险因素评估与预后
- 工程维修管理制度
- 仓库物料管理制度
- 斯珀特文体广场项目策划营销方案(初案)
- 北师大版第四单元认识图形的教学设计
- 基于WEB的数据库信息系统设计实训报告
- 数学建模优秀论文--基于遗传算法的机组组合问题的建模与求解