Cisco PIX防火墙的配置及注解完全手册

更新时间:2023-06-12 12:13:01 阅读量: 实用文档 文档下载

说明:文章内容仅供预览,部分内容可能不全。下载后的文档,内容与下面显示的完全一致。下载之前请确认下面内容是否您想要的,是否完整无缺。

Cisco PIX防火墙的配置及注解完全手册.doc

Cisco PIX防火墙的配置及注解完全手册

2008-10-21 10:00:24

标签:Cisco PIX 防火墙

Cisco PIX防火墙的配置及注解完全手册

PIX Version 6.3(1)

interface ethernet0 auto 设定端口0 速率为自动

interface ethernet1 100full 设定端口1 速率为100兆全双工

interface ethernet2 auto 设定端口2 速率为自动

nameif ethernet0 outside security0 设

定端口0 名称为 outside 安全级别为0

nameif ethernet1 inside security100 设定端口1 名称为 inside 安全级别为100 nameif ethernet2 dmz security50 设定端口2 名称为 dmz 安全级别为50 enable password Dv0yXUGPM3Xt7xVs encrypted 特权密码

passwd 2KFQnbNIdI.2KYOU encrypted 登陆密码

hostname hhyy 设定防火墙名称

fixup protocol ftp 21

fixup protocol h323 h225 1720

fixup protocol h323 ras 1718-1719

fixup protocol http 80

fixup protocol ils 389

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol sip 5060

Cisco PIX防火墙的配置及注解完全手册.doc

fixup protocol sip udp 5060

no fixup protocol skinny 2000

fixup protocol smtp 25

fixup protocol sqlnet 1521

允许用户查看、改变、启用或禁止一个服务或协议通过PIX防火墙,防火墙默认启用了一些常见的端口,但对于ORACLE等专有端口,需要专门启用。

names

access-list 101 permit ip 192.168.99.0 255.255.255.0 192.168.170.0 255.255.255.0

access-list 101 permit ip 192.168.12.0 255.255.255.0 192.168.180.0 255.255.255.0

access-list 101 permit ip 192.168.23.0 255.255.255.0 192.168.180.0 255.255.255.0

access-list 101 permit ip 192.168.99.0 255.255.255.0 192.168.101.0 255.255.255.0

建立访问列表,允许特定网段的地址访问某些网段

access-list 120 deny icmp 192.168.2.0 255.255.255.0 any

access-list 120 deny icmp 192.168.3.0 255.255.255.0 any

access-list 120 deny icmp 192.168.4.0 255.255.255.0 any

access-list 120 deny icmp 192.168.5.0 255.255.255.0 any

access-list 120 deny icmp 192.168.6.0 255.255.255.0 any

access-list 120 deny icmp 192.168.7.0 255.255.255.0 any

Cisco PIX防火墙的配置及注解完全手册.doc

access-list 120 deny icmp 192.168.8.0 255.255.255.0 any

access-list 120 deny icmp 192.168.9.0 255.255.255.0 any

access-list 120 deny icmp 192.168.10.0 255.255.255.0 any

access-list 120 deny icmp 192.168.11.0 255.255.255.0 any

access-list 120 deny icmp 192.168.12.0 255.255.255.0 any

access-list 120 deny icmp 192.168.13.0 255.255.255.0 any

access-list 120 deny icmp 192.168.14.0 255.255.255.0 any

access-list 120 deny icmp 192.168.15.0 255.255.255.0 any

access-list 120 deny icmp 192.168.16.0 255.255.255.0 any

access-list 120 deny icmp 192.168.13.0 255.255.255.0 any

access-list 120 deny icmp 192.168.14.0 255.255.255.0 any

access-list 120 deny icmp 192.168.15.0 255.255.255.0 any

access-list 120 deny icmp 192.168.16.0 255.255.255.0 any

access-list 120 deny icmp 192.168.17.0 255.255.255.0 any

access-list 120 deny icmp 192.168.18.0 255.255.255.0 any

access-list 120 deny icmp 192.168.19.0 255.255.255.0 any

access-list 120 deny icmp 192.168.20.0 255.255.255.0 any

access-list 120 deny icmp 192.168.21.0 255.255.255.0 any

access-list 120 deny icmp 192.168.22.0 255.255.255.0 any

access-list 120 deny udp any any eq netbios-ns

access-list 120 deny udp any any eq netbios-dgm

access-list 120 deny udp any any eq 4444

Cisco PIX防火墙的配置及注解完全手册.doc

access-list 120 deny udp any any eq 1205

access-list 120 deny udp any any eq 1209

access-list 120 deny tcp any any eq 445

access-list 120 deny tcp any any range 135 netbios-ssn

access-list 120 permit ip any any

建立访问列表120防止各个不同网段之间的ICMP发包及拒绝135、137等端口之间的通信(主要防止冲击波病毒)

access-list 110 permit ip 192.168.99.0 255.255.255.0 192.168.101.0 255.255.255.0

pager lines 24

logging on

logging monitor debugging

logging buffered debugging

logging trap notifications

mtu outside 1500

mtu inside 1500

mtu dmz 1500

ip address outside 10.1.1.4 255.255.255.224 设定外端口地址

ip address inside 192.168.1.254 255.255.255.0 设定内端口地址

ip address dmz 192.168.19.1 255.255.255.0 设定DMZ端口地址

ip audit info action alarm

ip audit attack action alarm

Cisco PIX防火墙的配置及注解完全手册.doc

ip local pool hhyy 192.168.170.1-192.168.170.254

建立名称为hhyy的地址池,起始地址段为:192.168.170.1-192.168.170.254 ip local pool yy 192.168.180.1-192.168.180.254

建立名称为yy 的地址池,起始地址段为:192.168.180.1-192.168.180.254 no failover

failover timeout 0:00:00

failover poll 15

no failover ip address outside

no failover ip address inside

no failover ip address dmz

no pdm history enable

arp timeout 14400

不支持故障切换

global (outside) 1 10.1.1.13-10.1.1.28

global (outside) 1 10.1.1.7-10.1.1.9

global (outside) 1 10.1.1.10

定义内部网络地址将要翻译成的全局地址或地址范围

nat (inside) 0 access-list 101

使得符合访问列表为101地址不通过翻译,对外部网络是可见的

nat (inside) 1 192.168.0.0 255.255.0.0 0 0

内部网络地址翻译成外部地址

Cisco PIX防火墙的配置及注解完全手册.doc

nat (dmz) 1 192.168.0.0 255.255.0.0 0 0

DMZ区网络地址翻译成外部地址

static (inside,outside) 10.1.1.5 192.168.12.100 netmask 255.255.255.255 0 0 static (inside,outside) 10.1.1.12 192.168.12.158 netmask 255.255.255.255 0 0 static (inside,outside) 10.1.1.3 192.168.2.4 netmask 255.255.255.255 0 0 设定固定主机与外网固定IP之间的一对一静态转换

static (dmz,outside) 10.1.1.2 192.168.19.2 netmask 255.255.255.255 0 0 设定DMZ区固定主机与外网固定IP之间的一对一静态转换

static (inside,dmz) 192.168.0.0 192.168.0.0 netmask 255.255.0.0 0 0 设定内网固定主机与DMZ IP之间的一对一静态转换

static (dmz,outside) 10.1.1.29 192.168.19.3 netmask 255.255.255.255 0 0 设定DMZ区固定主机与外网固定IP之间的一对一静态转换

access-group 120 in interface outside

access-group 120 in interface inside

access-group 120 in interface dmz

将访问列表应用于端口

conduit permit tcp host 10.1.1.2 any

conduit permit tcp host 10.1.1.3 any

conduit permit tcp host 10.1.1.12 any

conduit permit tcp host 10.1.1.29 any

设置管道:允许任何地址对全局地址进行TCP协议的访问

conduit permit icmp 192.168.99.0 255.255.255.0 any

Cisco PIX防火墙的配置及注解完全手册.doc

设置管道:允许任何地址对192.168.99.0 255.255.255.0地址进行PING测试 rip outside passive version 2

rip inside passive version 2

route outside 0.0.0.0 0.0.0.0 10.1.1.1

设定默认路由到电信端

route inside 192.168.2.0 255.255.255.0 192.168.1.1 1

route inside 192.168.3.0 255.255.255.0 192.168.1.1 1

route inside 192.168.4.0 255.255.255.0 192.168.1.1 1

route inside 192.168.5.0 255.255.255.0 192.168.1.1 1

route inside 192.168.6.0 255.255.255.0 192.168.1.1 1

route inside 192.168.7.0 255.255.255.0 192.168.1.1 1

route inside 192.168.8.0 255.255.255.0 192.168.1.1 1

route inside 192.168.9.0 255.255.255.0 192.168.1.1 1

route inside 192.168.10.0 255.255.255.0 192.168.1.1 1

route inside 192.168.11.0 255.255.255.0 192.168.1.1 1

设定路由回指到内部的子网

timeout xlate 3:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00

timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute

aaa-server TACACS+ protocol tacacs+

Cisco PIX防火墙的配置及注解完全手册.doc

aaa-server RADIUS protocol radius

aaa-server LOCAL protocol local

no snmp-server location

no snmp-server contact

snmp-server community public

no snmp-server enable traps

floodguard enable

sysopt connection permit-ipsec

sysopt connection permit-pptp

service resetinbound

service resetoutside

crypto ipsec transform-set myset esp-des esp-md5-hmac 定义一个名称为myset的交换集

crypto dynamic-map dynmap 10 set transform-set myset

根据myset交换集产生名称为dynmap的动态加密图集(可选) crypto map vpn 10 ipsec-isakmp dynamic dynmap

将dynmap动态加密图集应用为IPSEC的策略模板(可选)

crypto map vpn 20 ipsec-isakmp

用IKE来建立IPSEC安全关联以保护由该加密条目指定的数据流 crypto map vpn 20 match address 110

为加密图指定列表110作为可匹配的列表

crypto map vpn 20 set peer 10.1.1.41

Cisco PIX防火墙的配置及注解完全手册.doc

在加密图条目中指定IPSEC对等体

crypto map vpn 20 set transform-set myset

指定myset交换集可以被用于加密条目

crypto map vpn client configuration address initiate

指示PIX防火墙试图为每个对等体设置IP地址

crypto map vpn client configuration address respond

指示PIX防火墙接受来自任何请求对等体的IP地址请求

crypto map vpn interface outside

isakmp enable outside

在外部接口启用IKE协商

isakmp key ******** address 10.1.1.41 netmask 255.255.255.255 指定预共享密钥和远端对等体的地址

isakmp identity address

IKE身份设置成接口的IP地址

isakmp client configuration address-pool local yy outside isakmp policy 10 authentication pre-share

指定预共享密钥作为认证手段

isakmp policy 10 encryption des

指定56位DES作为将被用于IKE策略的加密算法

isakmp policy 10 hash md5

指定MD5 (HMAC变种)作为将被用于IKE策略的散列算法

isakmp policy 10 group 2

Cisco PIX防火墙的配置及注解完全手册.doc

指定1024比特Diffie-Hellman组将被用于IKE策略

isakmp policy 10 lifetime 86400

每个安全关联的生存周期为86400秒(一天)

vpngroup cisco idle-time 1800

vpngroup pix_vpn address-pool yy

vpngroup pix_vpn idle-time 1800

vpngroup pix_vpn password ********

vpngroup 123 address-pool yy

vpngroup 123 idle-time 1800

vpngroup 123 password ********

vpngroup 456 address-pool yy

vpngroup 456 idle-time 1800

vpngroup 456 password ********

telnet 192.168.88.144 255.255.255.255 inside

telnet 192.168.88.154 255.255.255.255 inside

telnet timeout 5

ssh timeout 5

console timeout 0

vpdn group 1 accept dialin pptp

vpdn group 1 ppp authentication pap

vpdn group 1 ppp authentication chap

vpdn group 1 ppp authentication mschap

Cisco PIX防火墙的配置及注解完全手册.doc

vpdn group 1 ppp encryption mppe 40

vpdn group 1 client configuration address local hhyy

vpdn group 1 pptp echo 60

vpdn group 1 client authentication local

vpdn username cisco password *********

vpdn enable outside

username cisco password 3USUcOPFUiMCO4Jk encrypted privilege 2 vpnclient vpngroup cisco_vpn password ********

vpnclient username pix password ********

terminal width 80

Cryptochecksum:9524a589b608c79d50f7c302b81bdfa4b

本文来源:https://www.bwwdw.com/article/h3b1.html

Top