铣床编制程序 - 图文

铣1.1.1

1

铣1.1.1

O11;（主程序） G54; M03S800; G00X0Y0Z20.; Z2.; M98P1000; G68X0Y0R-180.; M98P1000; G69; M98 P2000; G68X0Y0R-66.; M98 P2000; G68X0Y0R-180.; M98 P2000; G68X0Y0R-246.; M98 P2000; G69; G00Z50.; X-100.Y100.; M05; M00; G55; （打孔程序） M03S600; G00X0Y0Z20.; X0Y40.; G99G81Z-10.R2.F30; X0Y0; X0Y-40.; G80; G00Z50.; X-100.Y100.; M05; M30; O1000;（子程序） G00X70.Y-60.; G01Z-4.9625F30; Y60.F100; X59.; Y-60.; X48.; Y60.; X37.; Y-60.; X26.; Y60.; G01X22.Y67.; G41D01X15.Y60.; G03Y-60.R350.; G01G40X22.Y-67.; G01Z2.; G01X71.Y67.; G01Z-9.F30; G41D02X63.939Y60.F100; G02Y-60.R300.;; G01G40X71.Y-67.; G01Z2.; M99; 轮廓用平底刀Φ12 打孔用钻头Φ12 D01＝6、D02＝6.03、D03＝6

2

O2000;（子程序） G00X40.Y33.; G01Z-9.F30; G41D03X40.148Y44.589F100; G03X30.111Y33.442R7.5; G02X42.798Y13.906R45.; G03X57.063Y18.541R7.5; G03X40.148Y44.589R60.; X30.111Y33.442R7.5; G01G40X40.Y33.; G01Z2.; M99; 铣1.1.2

3

铣1.1.2

O12;(主程序) G54; M03S600; G00X0Y0Z20.; X28.Y18.; Z2.; G01Z-4.975F30; X-28.F100; Y11.; X28.; Y4.; X-28.; Y-3.; X28.; Y-10.; X-28.; Y-17.; X28.; G01X21.Y-21.; G41D01X26.Y-26.; G03X36.Y-16.R10.; G01Y16.; G03X26.Y26.R10.; G01X-26.; G03X-36.Y16.R10.; G01Y-16.; G03X-26.Y-26.R10.; G01X26.; G03X36.Y-16.R10.; G01G40X31.Y-11.; G01Z2.; X11.Y-21.5.; Z-10.F30; G41D02X16.Y-26.F100; G03X21.Y-21.R5.; G01Y-16.; G02X26.Y-11.R5.; G01X31.; G03X36.Y-6.R5.; G01Y6.; G03X31.Y11.R5.; G01X26.; G02X21.Y16.R5.; G01Y21.; G03X16.Y26.R5.;

G01X-16.; G03X-21.Y21.R5.; G01Y16.; G02X-26.Y11.R5.; G01X-31.; G03X-36.Y6.R5.; G01Y-6.; G03X-31.Y-11.R5.; G01X-26.; G02X-21.Y-16.R5.; G01Y-21.; G03X-16.Y-26.R5.; G01X16.; G03X21.Y-21.R5.; G01G40X16.5Y-16.; G01Z2.; M98 P1000; G68X0Y0R-180.; M98 P1000; G69; G00Z50.; X-100.Y100.; M05; M00; G55; （打孔程序） M03S600; G00X0Y0Z20.; X28.Y18.; G99G81Z-15.R2.F30; Y-18.; X-28.; Y18.; G80; G00Z50.; X-100.Y100.; M05; M30; 轮廓用平底刀Φ8 打孔用钻头Φ8 D01＝4、D02＝3.981、D03＝4.012 O1000;（子程序） G00X3.Y21.5; G01Z-10.F30; G41D03X9.118Y17.F100; G02X12.097Y14.353R3.; G03X16.269Y2.824R14.; G02Y-2.824R3.; G03X12.097Y-14.353R14.; G02X9.118Y-17.R3.; G01X5.; Y17.; X9.118; G02X12.097Y14.353R3.; G01G40X20.Y6.; X28.; Y-6.; G01Z2.; M99; 4

铣1.1.3

5

铣1.1.3

O13;（主程序） G54; M03S600; G00X0Y0Z20.; Z2.; M98 P1000; G68X0Y0R-180.; M98 P1000; G69; G01X-21.Y15.3; Z-3.975F30; X21.F100; Y-15.3; X-21.; Y15.3; G01X0Y15; G41D02X10.Y10.; G02X15.Y5.R5.; G01Y-5.; G02X10.Y-10.R5.; G01X-10.; G02X-15.Y-5.R5.; G01Y5.; G02X-10.Y10.R5.; G01X10.; G02X15.Y5.R5.; G01G40X20.Y0.; G01Z2.; M98 P2000; G51X0Y0I1000J-1000; M98 P2000; G51X0Y0I-1000J-1000; M98 P2000; G51X0Y0I-1000J1000; M98 P2000; G50; G00Z50.; X-100.Y100.; M05; M00; G55；（打孔程序） M03S600; G00X0Y0Z20.; X21.Y15.3; G99G81Z-15.R2.F30; Y-15.3; X-21.; Y15.3; G80; G00Z50.; X-100.Y100.; M05; M30; 轮廓用平底刀Φ8 打孔用钻头Φ8 D01＝4.023、D02＝3.981、 D03＝4 O1000;（子程序） O1000; G00X-46.; G01Z-3.975F30; X-47.F100; Y27.5; X-37.5Y40.; X37.5; X47.Y27.5; Y0; X46.; Z2.; G00X0Y40.; G01Z-3.975F30; G41D01X-13.611Y32.804F100; G03X13.611R35.; G02X38.544Y8.005R19.; X28.387Y12.228R5.5; G03X15.841Y21.414R8.; G02X11.972Y20.R6.; G01X-11.972; G02X-15.841Y21.414R6.; G03X-28.387Y12.228R8.; G02X-38.544Y8.005R5.5; X-13.611Y32.804R19.; G03X13.611R35.; G01G40X0Y40.; G01Z2.; M99; O2000;（子程序） G00X48.Y38.; G01Z-9.F30; G01X42.Y46.F100; G41D03X37.5Y41.; G01Y40.; G03X50.Y27.5R12.5; G01X51.; G40X55.Y32.; G01Z2.; M99; 6

铣1.1.4

7

铣1.1.4

O14;（主程序） G54; M03S600; G00X0Y0Z20.; Z2.; X51.Y-37.; G01Z-4.F30; X-51.F100; Y37.; X51.; Y-30.; X-51.; Y30.; X51.; X21.Y34.; G02Y-34.R34.; G01X-21.; G02Y34.R34.; G01X-6.Y30.; G41D01X0Y25.F150; G01X21.; G02Y-25.R25.; G01X-21.; G02Y25.R25.; G01X3.; G40X10.Y30.; Z2.; G01X4.Y7.; Z-2.975F30; G41D02X10.046Y2.F100; G03X14.259Y4.308R5.; G02X29.Y0.R8.; G03X41.R6.; G03X21.Y20.R20.; G01X-21.; G03X-41.Y0R20.; G03X-29.Y0R6.; G02X-14.259Y4.308R8.; G03X-10.046Y2.R5.; G01X10.046; G03X14.259Y4.308R5.; G01G40X10.Y11.; X-10.; Z2.; M98 P1000;

G51X0Y0I1000J-1000; M98 P1000; G51X0Y0I-1000J-1000; M98 P1000; G51X0Y0I-1000J1000; M98 P1000; G50; G00Z50.; X-100.Y100.; M05; M00; G55; （打孔程序） M03S600; G00X0Y0Z20.; X21.Y0; G99G81Z-10.R2.F30; X0Y-15.; X-21.Y0; G80; G00Z50.; X-100.Y100.; M05; M30; 轮廓用平底刀Φ8 打孔用钻头Φ8 D01＝4.032、D02＝4.015、 D03＝3.99 O1000;（子程序） G00X30.Y32.; G01Z-7.F30; G41D03X32.015Y35.455F100; G03X27.985Y28.545R4.; G01X39.985Y21.545; G03X44.015Y28.455R4.; G01X32.015Y35.455R4.; G03X27.985Y28.545R4.; G01G40X30.Y32.; G01Z2.; M99; 8

铣1.1.5

9

铣1.1.5

O15;（主程序） G17G90; G54; M03S600; G00X0Y0Z20.; Z2.; X47.Y40.; G01Z-4.975F30; Y-40.F100; X40.; Y0; X33.Y-40.; X-47.; Y40.; X-40.; Y0; X-33.Y40.; G01X30.Y40.; G41D01X35.Y35.; G02X39.935Y29.199R5.; G01X32.242Y-18.204; G02X12.5Y-35.R20.; G01X-35.; G02X-39.935Y-29.199R5.; G01X-32.242Y18.204; G02X-12.5Y35.R20.; G01X36.; G40X41.Y40.; Z2.; M98 P1000; G51X0Y0I-1000J-1000; M98 P1000; G50; G00Z50.; X-100.Y100.; M05; M00;

G17G90G55; （球头刀程序） M03S1000; G00X0Y0Z20.; X0Y-36.; M98 P7202000; G90; G00Z50.; X-100.Y100.; M05; M30; 轮廓用平底刀Φ8 球头铣刀Φ16 D01＝4.024、D02＝4.028 D03=4、D04=8 O1000;（子程序） G00X47.Y0; G01Z-8.F30; Y-40.F100; X40.; X47.Y0.; G01X55.； Y46.; G41D02X50.Y41.; G01Y40.; X30.324Y-40.; Y-41.; G40X35.Y-45.; G01Z2.; X50.Y-40.; G01Z-11.F30; G41D03X50.Y-33.597F100; X44.247Y-28.994; G03X38.Y-36.803R5.; G01X41.996Y-40.; G40X50.Y-40.; G01Z2.; M99; O2000;（球头刀子程序） G18G90; G01X0Z16.F200; G41D04X9.Z0; X5.527Z-2.3; G03X-5.527R10.; G01X-9.Z0; G40X0Z16.; G17; G91; Y0.1; M99; 10

铣1.1.6

11

铣1.1.6

O16; G17G90; G54; M03S600; G00X0Y0Z20.; Z2.; M98 P1000; G51X0Y0I-1000J1000; M98 P1000; G50; G00Z50.; X-100.Y100.; M05; M00; G17G90G55; （球头刀程序） M03S1000; G00X0Y0Z20.; X0Y-51.; M98 P10202000; G90; G00Z50.; X-100.Y100.; M05; M30; O1000; G00X45.Y0.; G01Z-6.F30; Y11.F100; G03Y-11.R11.; G01Y-22.; G02Y22.R22.; G01X53.Y28. G41D01X46.Y35.; X45.; G03Y-35.R35.; G01X46.; G40X53.Y-28.; G01Z2.; X27.5Y-38.; G01Z-4.F60; Y38.F150; X33.5; G41D02X27.Y45.; G03X15.Y33.R12.; G01Y-33.; G03X27.Y-45.R12.; G01X32.; G03X40.Y-37.R8.; G01Y37.; G03X32.Y45.R8.; G01X27.; 轮廓用平底刀Φ12 G03X15.Y33.R12.; 球头铣刀Φ8 G01G40X22.Y26.; D01＝6.018、D02＝5.98、D03＝4 G01Z2.; M99;

12

O2000; （球头刀子程序） G18G90; G01X0Z8.F200; G41D03X6.Z0.; X3.586Z-2.484; G03X-3.586R5.; G01X-6.Z0; G40X0Z8.; G17; G91; Y0.1; M99; 铣1.1.7

13

铣1.1.7

O17; G17G90; G54; M03S600; G00X0Y0Z20.; Z2.; X-20.Y-46.; G01Z-4.975F30; Y41.F100; X-11.; Y-41.; X-2.; Y41.; X7.; Y-41.; X16.; Y41.; X21.; Y-41.; G01Z2.; X-9.Y24.; G01Z-9.F30; G41D01X-15.Y30.F100; G03X-21.Y24.R6.; G01Y16.882; G03X-20.032Y13.614R6.; G02Y-13.614R25.; G03X-21.Y-16.882R6.; G01Y-24.; G03X-15.Y-30.R6.; G01X15.; G03X21.Y-24.R6.; G01Y-16.882; G03X20.032Y-13.614R6.; G02Y13.614R25.; G03X21.Y16.882R6.; G01Y24.; G03X15.Y30.R6.; G01X-15.; G03X-21.Y24.R6.; G01G40X-15.Y19.; G01X-7.Y24.; G41D02X-1.Y18.5; G01X0.; G02X6.874Y8.R7.5;

G03Y-8.R20.; G02X-6.874R-7.5; G03Y8.R20.; G02X0Y18.5R7.5; G01X1.; G40X7.Y24.; G01Z2.; G00Z50.; X-100.Y100.; M05; M00; G55; （球头刀程序） M03S600; G00X0Y0Z20.; X-36.Y42.Z2.; M98 P1201000; G90; G00Z50.; X-100.Y100.; M05; M30; 轮廓用平底刀Φ10 球头铣刀Φ10 D01＝4.973、D02＝4.977 O1000; （球头刀子程序） G19G90; G00Y42.Z2.; Z-5.F60; Y31.; G02Y29.114Z-4.696R6.; G03Y-29.114R92.6; G02Y-31.Z-5.R6.; G01Y-42.; Z2.; G17; G91; X0.1; M99; 14

铣1.1.8

15

铣1.1.8

O18; G17G90; G54; M03S800; G00X0Y0Z20.; Z2.; X-44.Y31.; G01Z-2.F30; Y-31.F100; X-35.; Y31.; X-26.; Y-31.; X-17.; Y31.; X-8.; Y-31.; X1.; Y31.; X10.; Y-31.; X19.; Y31.; X0Y0; G16; G41D01X30.1Y-30.; G03X30.Y30.R30.; G02X45.Y30.R7.5; X45.Y-30.R45.; X30.Y-30.R7.5; G03X30.Y30.R30.; G15; G01G40X0Y0; G01Z2.; G01X-32.5Y-31.; G01Z-5.975F30; Y31.F100; Y26.; X20.; Y32.; X51.; Y-32.; X20.; Y-26.; X-25.;

Y26.; G01X-24.Y-6.; G41D01X-18.Y0F150; Y8.718; G02X10.815Y16.824R20.; G03X25.51Y21.53R10.; G16G02X45.Y30.R7.5; X45.Y-30.R45.; G15X25.51Y-21.53R7.5; G03X10.815Y-16.824R10.; G02X-18.Y-8.718R20.; G01Y2.; G40X-24.Y8.; G01Z2.; X0Y0; Z-7.F60; Y-2.F150; G41D02X8.Y0.; G03I-8.; G03X0Y8.R8.; G01G40X-2.Y0.; G01Z2.; G00Z50.; X-100.Y100.; M05; M00; G55; M03S1000; G00X0Y0Z20.; X-48.Y32.Z2.; M98 P1101000; G90; G00Z50.; X-100.Y100.; M05; M30; 轮廓用平底刀Φ10 球头铣刀Φ8 D01＝4.974、D02＝5.027 O1000; （球头刀子程序） G19G90; G00Y32.Z2.; Z-6.F100; Y30.F300; G02Y28.8Z-5.854R5.; G03Y-28.8R120.; G02Y-30.Z-6.R5.; G01Y-32.; Z2.; G17; G91; X0.1; M99; 16

铣1.2.1

17

铣1.2.1

O21; G17G90; G54; M03S600; G00X0Y0Z20.; Z2.; X-37.Y-41.; G01Z-2.975F30; Y41.F100; X-30.; Y-41.; X-23.; Y41.; X-16.; Y-41.; X-9.; Y41.; G01X-7.Y43.; G41D01X-2.Y37.5; X0; G02X7.309Y36.781R37.5; G03X20.84Y31.176R8.; G02X31.176Y20.84R37.5; G03X36.781Y7.309R8.; G02Y-7.309R37.5; G03X31.176Y-20.84R8.; G02X20.84Y-31.176R37.5; G03X7.309Y-36.781R8.; G02X0Y-37.5R37.5; G01Y40.; G40X-5.Y45.; G01Z2.; X-8.Y20.; G01Z-6.F60; Y-20.F150; Y0; X-20.; G41D02X-25.Y8.; G03Y-8.R8.; G01X-16.; Y-20.; G03X0.R8.; G01Y20.; G03X-16.R8.; G01Y8.;

X-25.; G03Y-8.R8.; G01G40X-20.Y0.; G01Z2.; M98 P1000; G68 X0Y0R60.; M98P1000; G68X0Y0R-60.; M98P1000; G69; G00Z50.; X-100.Y100.; M05; M00; G55; （打孔程序） M03S600; G00X0Y0Z20.; X-8.Y20.; G99G81Z-16.R2.F30; X-25.Y0; X-8.Y-20.; G80; G00Z50.; X-100.Y100.; M05; M30; 轮廓用平底刀Φ8 打孔用钻头Φ8 D01＝4、D02＝3.972、D03＝3.98 O1000; G00X20.Y0.; G01Z-4.F30.; G41D03X25.Y-4.F100; G03Y4.R4.; G01X17.; G03Y-4.R4.; G01X25.; G03Y4.R4.; G01G40X20.Y0.; G01Z2.; M99; 18

铣1.2.2

19

铣1.2.2

O22; G17G90; G54; M03S600; G00X0Y0Z20.; Z2.; G01X50.Y31.F100; G01Z-3.975F30; G41D01X40.Y36.100; X-35.; G03Y-36.R50.; G01X40.; G40X47.Y-31.; Y31.; X40.; Y-31.; X33.; Y31.; X26.; Y-31.; X19.; Y31.; X12.; Y-31.; X5.; Y31.; X-13.; G41D02X-21.79Y24.; G03X-5.79R8.; G01X-3.; G02X0Y21.R3.; G01Y-21.; G02X-3.Y-24.R3.; G01X-5.79; G03X-21.79R8.; G01X-27.581; G02Y24.R42.; G01X-21.79; G03X-5.79R8.; G01G40X-13.Y31.; G01Z2.; G01X41.Y31.; Z-9.F30; G41D03X36.Y36.F100; X5.;

G03X0Y31.R5.; G01Y-31.; G03X5.Y-36.R5.; G01X36.; G40X47.Y-31.; Y31.; X40.; Y-31.; X33.; Y31.; X26.; Y-31.; X19.; Y31.; X12.; Y-31.; G01Z2.; M98P1000; G51 X25Y0I1000J-1000; M98P1000; G50; G00Z50.; X-100.Y100.; M05; M00; G55; （打孔程序） M03S600; G00X0Y0Z20.; X0Y42.5; G99G81Z-10.R2.F60; X-20.Y0; X0Y-42.5; G80; G00Z50.; X-100.Y100.; M05; M30; O1000; G52X25.Y0; G00G16X19.Y70.; G01Z-12.F30; G41D04X13.Y60.F100; G03X25.Y60.R6.; X25.Y120.R25.; X13.Y120.R6.; G02X13.Y60.R13.; G03X25.Y60.R6.; G01G40X19.Y70.; G15G01Z2.; G52X0Y0； M99; 轮廓用平底刀Φ8 打孔用钻头Φ8 D01＝4.026、D02＝3.972、 D03＝4.026、D04＝4 20

铣1.2.3

21

铣1.2.3

O23; G17G90; G54; M03S600; G00X0Y0Z20.; Z2.; X0Y50.; G01Z-3.965F30; G02J-50.F100; G01Y45.; G02J-45.; G01X-5.Y40.; G41D01X0Y34.641; G16X40.Y60.; X40.Y0; X40.Y-60.; X40.Y-120.; X40.Y-180.; X40.Y120.; G15X2.; G40X7.Y40.; G01Z2.; M98P1000; G51X0Y0I1000J-1000; M98P1000; G51X0Y0I-1000J-1000; M98P1000; G51X0Y0I-1000J1000; M98P1000; G50; M98P2000; G51X0Y0I1000J-1000; M98P2000; G50; G00Z50.; X-100.Y100.; M05; M00; G55; （打孔程序） M03S600; G00X0Y0Z20.; G16X11.Y45.; G99G81Z-12.R2.F30; X11.Y135.; X11.Y225.;

X11.Y-45.; G15G80; G00Z50.; X-100.Y100.; M05; M30; 轮廓用平底刀Φ8 打孔用钻头Φ8 D01＝4.027、D02＝4、D03＝4 O1000; G00G16X22.5Y45.; G01Z-5.F30; G41D02X17.5Y30.F100; G03X27.5Y30.R5.; X27.5Y60.R27.5; X17.5Y60.R5.; G02X17.5Y30.R17.5; G03X27.5Y30.R5.; G01G40X22.5Y45.; G15; G01Z2.; M99; O2000; G00X-35.Y46.; G01Z-9.F30; G41D03X-30.Y41.875F100; X-27.322; G03X27.322R200.; G01X30.; G40X35.Y46.; Y50.; X-20.; G01Z2.; M99; 22

铣1.2.4

23

铣1.2.4

O24; G17G90; G54; M03S600; G00X0Y0Z20.; Z2.; M98P1000; G51X0Y0I1000J-1000; M98P1000; G51X0Y0I-1000J-1000; M98P1000; G51X0Y0I-1000J1000; M98P1000; G50; G00X-56.Y56.; G01Z-7.F30.; X56.F100; Y-56.; X-56.; Y49.; G01X-6.Y49.; G41D02X0Y42.4265; X42.4265; Y-42.4265; X-42.4265; Y42.4265; X2.; G40X8.Y49.; G01Z2.; X9.Y0.; G01Z-7.F30; G41D03X15.Y-6.F100; G03Y6.R6.; G01X6.; Y15.; G03X-6.R6.; G01Y6.; X-15.; G03Y-6.R6.; G01X-6.; Y-15.; G03X6.R6.; G01Y-6.; X15.; G03Y6.R6.;

G01G40X9.Y0.; G01Z2.; G00Z50.; X-100.Y100.; M05; M00; G55; （打孔程序） M03S600; G00X0Y0Z20.; G01X0Y50.; G99G81Z-17.R2.F30; X50.Y0; X0Y-50.; X-50.Y0; G80; G00Z50.; X-100.Y100.; M05; M30; O1000; G00X5.Y49.; G01Z-3.975F30; G41D01X11.Y42.4265F100; X28.284; G02X32.998Y39.093R5.; G03X39.093Y32.998R10.; G02X42.426Y28.284R5.; G01Y11.; G02X37.4265Y6.R5.; G01X31.113; G02X26.399Y9.333R5.; G03X9.333Y26.399R28.; G02X6.Y31.113R5.; G01Y37.4265; G02X11.Y42.4265R5.; G01X13.; G40X19.Y49.; G01X0.Y56.; X56.; 轮廓用平底刀Φ10 Y0; 打孔用钻头Φ8 X20.; D01＝5.014、D02＝5、D03＝5.022 X3.Y20.; Y3.; X20.; G01Z2.; M99; 24

铣1.2.5

25

铣1.2.5

O01; G17G90; G54; M03S600; G00X0Y0Z20.; Z2.; X0Y47.; G01Z-3.955F30; G02J-47.F100; G01X-5.Y42.; G41D01X0Y36.955; G16X40.Y67.5; X40.Y22.5; X40.Y-22.5; X40.Y-67.5; X40.Y-112.5; X40.Y-157.5; X40.Y157.5; X40.Y112.5; G15X2.; G40X7.Y42.; G01Z2.; M98P1000; G51X0Y0I1000J-1000; M98P1000; G51X0Y0I-1000J-1000; M98P1000; G51X0Y0I-1000J1000; M98P1000; G50; M98P2000; G51X0Y0I1000J-1000; M98P2000; G50; G01Z2.; G00Z50.; X-100.Y100.; M05; M30; G55; M03S1000; G00X0Y0Z20.; X0Y-38.; M98 P7603000; G90;

G00Z50.; X-100.Y100.; M05; M30; 轮廓用平底刀Φ8 球头铣刀Φ6 D01＝4.027、D02＝4、D03＝4 O1000; G00G16X25.Y45.; G01Z-5F30; G41D02X20.Y30.F100; G03X30.Y30.R5.; X30.Y60.R30.; X20.Y60.R5.; G02X20.Y30.R20.; G03X30.Y30.R5.; G01G40X25.Y45.; G15G01Z2.; M99; O2000; G00X-35.Y46.; G01Z-9.F30; G41X-30.Y41.875F100; X-27.322; G03X27.322R200.; G01X30.; G40X35.Y46.; Y50.; X-20.; G01Z2.; M99; O3000; G18G90; G01X0Z6.F200; G41D04X4.5Z0; X2.957Z-1.694; G03X-2.957R4.; G01X-4.5Z0; G40X0Z6.; G17; G91; Y0.1; M99; 26

铣1.2.6

27

铣1.2.6

O26; G17G90; G54; M03S600; G00X0Y0Z20.; Z2.; X-45.Y-47.; G01Z-5.F30; Y47.F100; X-34.; Y-37.; X-23.; Y47.; X-12.; Y-47.; X20.; X-1.; Y47.; X20.; X5.; G01X5.Y20.; G41D01X12.Y27.5; G02X27.129Y31.129R8.; G01X41.129Y3.629; G02Y-3.629R8.; G01X27.129Y-31.129; G02X12.Y-27.5R8.; G01Y30.; G40X5.Y37.; G01Z2.; G01X-22.Y19.; Z-9.F30; G41D02X-14.Y25.F100; G03X-30.R8.; G01Y8.; X-36.; G03Y-8.R8.; G01X-30.; Y-25.; G03X-14.R8.; G01Y25.; G03X-30.R8.; G01G40X-22.Y19.; G01Z2.; G00Z50.;

X-100.Y100.; M05; M00; G55; M03S1000; G00X0Y0Z20.; X0Y-51.; M98 P10201000; G90; G00Z50.; X-100.Y100.; M05; M30; 轮廓用平底刀Φ12 球头铣刀Φ10 D01＝5.972、D02＝5.972 O1000; G18G90; G01X0Z5.F200; G41D03X6.Z-5.; X3.6Z-6.8; G03X-3.6R6.; G01X-6.Z-5.; G40X0Z5.; G17; G91; Y0.1; M99; 28

铣1.2.7

29

铣1.2.7

O27; G17G90; G54; M03S600; G00X0Y0Z20.; Z2.; M98P1000; G68X0Y0R180.; M98P1000; G69; G01Z2.; M98P2000; G68X0Y0R-45.; M98P2000; G68X0Y0R-135.; M98P2000; G68X0Y0R-180.; M98P2000; G68X0Y0R135.; M98P2000; G68X0Y0R45.; M98P2000; G69; G00Z50.; X-100.Y100.; M05; M00; G55; M03S1000; G00X0Y0Z20.; X-6.Y42.Z2.; M98 P1203000; G90; G00Z50.; X-100.Y100.; M05; M30; O1000; G00X-11.Y40.; G01Z-3.975F30; G41D01X-6.Y35.F100; X6.; G40X11.Y40.; X9.; Y-37.; X16.; Y37.; X23.; Y-37.; X30.; Y37.; X37.; Y-37.; X40.; Y27.; G01Z-7.975F30.; G41D02X34.641Y21.F100; Y20.; G03Y-20.R150.; G01Y-22.; G40X40.Y-27.; G01Z2.; M99; O2000; G00X21.Y0.; G01Z-9.F30; G41D03X26.Y-5.F100; G03Y5.R5.; G01X18.; G03Y-5.R5.; G01X26.; G03Y5.R5.; G01G40X21.Y0.; G01Z2.; M99; 30

O3000; G19G90; G00Y42.Z2.; Z-5.F100; Y40.F300; G03Y-40.R162.5; G01Y-42.; Z2.; G17; G91; X0.1; M99; 轮廓用平底刀Φ8 球头铣刀Φ12 D01＝3.973、D02＝4、D02＝3.972

铣1.2.8

31

铣1.2.8

O28; G17G90; G54; M03S600; G00X0Y0Z20.; Z2.; M98P1000; G68X0Y0R-180.; M98P1000; G69; G00Z50.; X-100.Y100.; M05; M30; G55; M03S1000; G00X0Y0Z20.; X-6.Y42.Z2.; M98 P1202000; G90; G00Z50.; X-100.Y100.; M05; M30; O1000; G00X-20.Y40.; G01Z-4.975F30; X11.F100; Y42.; G41D01X5.Y36.; Y-36.; G40X11.Y-42.; X19.Y-37.; Y37.; X28.; Y-37.; X37.; Y37.; G01Z2.; G01X40.Y0.; Z-9.F60; Y9.; G03Y-9.R9.; G01Y0; G41D02X33.672Y21.592; G03Y-21.592R22.5; G01G40X40.Y0; G01Z2.; X16.Y13.; 轮廓用平底刀Φ10 G01Z-7.F30; 球头铣刀Φ12 G41D03X22.Y18.F100; D01＝5.011、D02＝5、D02＝5.026 G03X10.R6.; G01Y-18.; G03X22.R6.; G01Y18.; G03X10.R6.; G01G40X16.Y13.; G01Z2.; M99;

32

O2000; G19G90; G00Y42.Z2.; Z-5.F100; Y40.F300; G03Y-40.R162.5; G01Y-42.; Z2.; G17; G91; X0.1; M99; 用10的键槽铣刀加工45#钢

首先看用什么材料的铣刀： 高速钢铣刀：

转速630r/min，垂直进给25/min(0.02mm/z)，横向进给64m/min(0.05mm/z)； 硬质合金非涂层铣刀：

转速2550r/min，垂直进给153/min(0.03mm/z)，横向进给306m/min(0.06mm/z)； 硬质合金涂层铣刀：

转速4138r/min，垂直进给248/min(0.03mm/z)，横向进给497m/min(0.06mm/z)。

33

本文来源：https://www.bwwdw.com/article/gzhx.html