PI3HDMI412ADZBE中文资料

1

PS884E 01/18/07

Block Diagram PI3HDMI412AD

1:2 Active HDMI Rev. 1.3 Compatible DeMux with Advanced

Re-Driver Functionality for Enhanced Signal Integrity

Features

? Supply voltage, V DD = 3.3V ±5%

? Compatible w/ DVI, HDMI 1.1, 1.2, and 1.3 signals ? Supports both AC-coupled and DC-coupled inputs ? 1:2 Demux

? Supports Deep Color, up to 12-bits per channel ? Con ? gurable output swing control (500mV , 750mV , 1000mV)? Con ? gurable Pre-Emphasis levels (0dB, 1.5dB, 3.5dB, 6.0dB)? Con ? gurable De-Emphasis (0dB, -1.5dB, -3.5dB, -6.0dB)? Con ? gurable Equalization (1dB,3.5dB, 6dB, 8dB)? Data Rate = 2.5Gbps (Max) ? ESD protection = 6kV (Typ) ? Inputs w/ built-in termination ? Propagation delay < 2ns input ? Uni-Directional

? Packaging (Pb-free & Green): 56-pad TQFN (ZB56)

Description

Pericom Semiconductor’s PI3HDMI412AD, active-drive switch solution is targeted for high-resolution video networks that are based on DVI/HDMI standards, and TMDS signal processing. The PI3HDMI412AD is an active single TMDS channel to two TMDS channe DeMux with Hi-Z outputs. The device drives differential signals to multiple video display units. It provides three controllable output swing levels that can be controlled through pin control or I 2C control, depending on the mode select pin. The swing levels are 500mV , 700mV & 1000mV . This solution also provides a unique advanced pre-emphasis technique to increase rise and fall times which are reduced during transmission across long distances.

The maximum DVI/HDMI data rate of 1.65Gbps provides a 1920x1080 resolution required by the next Gen HDTV and PC graphics products. Due to its active uni-directional feature, this switch is de-signed for usage only for the video driver’s side. For PC graphics application, the device sits at the driver’s side to switch between multiple display units, such as PC LCD monitor, projector, TV , etc.

PI3HDMI412AD is the industry’s ? rst active DVI/HDMI compliant switch, which ensures transmitting high bandwidth video streams from PC graphics source to end display units. PI3HDMI412AD will also provide enhanced robust ESD/EOS protection of 8kV contact, which is required by many consumer video networks today.

Pin Con ? guration

07-0013

元器件交易网

2

PS8842E 01/18/07

PI3HDMI412AD

1:2 Active HDMI Rev. 1.3 Compatible DeMux with

Advanced Re-Driver Functionality for Enhanced Signal Integrity

Storage Temperature.....................................–65°C to +150°C

Supply V oltage to Ground Potential.............–0.5V to +5V DC Input V oltage..........................................–0.5V to V DD DC Output Current.......................................120mA Power Dissipation.........................................1.0W

Note: Stresses greater than those listed under MAX I M UM RAT I NGS may cause permanent damage to the de v ice. This is a stress rating only and func t ion a l op e r a t ion of the device at these or any other conditions above those indicated in the operational sections of this spec i ? c a t ion is not implied. Exposure to absolute max i m um rating con d i t ions for extended periods may affect re l i a bil i t y.

Maximum Ratings (Above which useful life may be im-paired. For user guide l ines, not tested.)

Function Block Description

Notes:

1. X = 0,1,2,3

2. Y = A,B

Pin Description

Pin #

Pin Name I/O

Description

2, 6, 11, 15, 22, 24, 36, 48V DD Power 3.3V power supply 3, 14, 21, 23, 27, 30, 33, 39, 42, 45, 53

GND

Power 0V power supply

16SEL_Out O Output bit, that provides information to user as to which port is active, if SEL_

OUT = ‘LOW’, then Port A is active, if SEL_OUT = ‘HIGH’, then Port B is active. Only used when MS pin is ‘HIGH’

19SCL I I 2C Clock Input Signal 20SDA I/O I 2C Data Input/Output Signal 18NC N/A No Connect.

1

MS

I

Mode Select Pin. If MS = ‘HIGH’, then I 2C control is active. Pins 49-52 are

I 2C address and pin 19 is SCL and pin 20 is SDA. If MS = ‘LOW’, then I 2C control is inactive and pin programmability is active. Pins 49-52 are control pins only for Port A, S4-S7 and pin 19 is S2 and pin 20 is S3. If 'MS' = "LOW", Port B cannot be con ? gured and is left as default.

55SEL_IN I Output port select. (Logically similar to I 2C bit S1 - see page 3)

54Test_in I Input pin for internal testing. Tie to GND for normal operation

56

OE

I Output is enabled and normal when OE = ‘HIGH’. If OE = ‘LOW’, both outputs, A and B, are disabled and at Hi-Z

17Test_Out

O Output pin for internal testing. Not used for normal operation 4, 5, 7, 8, 9, 10, 12, 13Dx I Input TMDS high speed signals 28, 29, 31, 32, 34, 35, 40, 41, 43, 44, 46, 47, 25, 26, 37, 38

Dx y O Output TMDS high speed signals 49,50, 51, 52A0, A1,

A2, A3

I I 2C address inputs if MS = ‘HIGH’.

49,50, 51, 52S4, S5,

S6, S7

I If MS = ‘LOW’, then pins 49-52 are control bits S4-S7 for port A only, as shown in truth table on page 3 of datasheet

19S3

I If MS = ‘LOW’, then pins 19 is control bit S3, as shown in the truth table on page 3

20

S2

I

If MS = ‘LOW’, then pins 20 is control bit S2, as shown in the truth table on page 3

07-0013

元器件交易网

3

PS8842E 01/18/07

PI3HDMI412AD

1:2 Active HDMI Rev. 1.3 Compatible DeMux with

Advanced Re-Driver Functionality for Enhanced Signal Integrity

BYTE 1 (Address Assignment)

Address A6A5A4A3A2A1A0R/W Value

1

1

A3

A2

A1

A0

R=1/W=0

07-0013元器件交易网

4

PS8842E 01/18/07

PI3HDMI412AD

1:2 Active HDMI Rev. 1.3 Compatible DeMux with

Advanced Re-Driver Functionality for Enhanced Signal Integrity

07-0013元器件交易网

5

PS8842E 01/18/07

PI3HDMI412AD

1:2 Active HDMI Rev. 1.3 Compatible DeMux with

Advanced Re-Driver Functionality for Enhanced Signal Integrity

TMDS Compliance Test Results

07-0013元器件交易网

6

PS8842E 01/18/07

PI3HDMI412AD

1:2 Active HDMI Rev. 1.3 Compatible DeMux with

Advanced Re-Driver Functionality for Enhanced Signal Integrity

DC Electrical Characteristics (T A = –40°C to +85°C, unless otherwise noted. V DD = 3.3V ±0.3V)Symbol Parameter

Test

Condition (1)

Min.Typ.(2)Max.Units V H Single-ended high level output voltage V DD – 10mV V DD

V DD + 10mV V V L Single-ended low level output voltage V DD – 600mV V DD - 400mV V Vswing Single-ended output swing voltage 400600mV V OFF Single-ended standby (off) output voltage V DD – 10mV

V DD V DD + 10mV V I OFF Single-ended standby (off) output current 10

μs V OS Offset V oltage

V DD – 250mV

V V IH Minimum Input High V oltage 1.8

V V IL Minimum Input Low V oltage 0.8

I CC

Power Supply Current

280

mA

AC Electrical Characteristics (T A = –40°C to +85°C, V DD = 3.3V ±0.3V)

Symbol Paramter

Test Conditions (1)

Min.Typ.(2)

Max.Units T 20-80

Rise time/fall time (20% - 80%)75

240ps

Overshoot 15% of V swing * 2Undershoot

25% of V swing * 2

Intra-Pair Skew at Source Connector 60ps Inter-Pair Skew at Connector 100ps Clock duty cycle

40%50%60%Through connection impedance 85

100

115ps TMDS differential clock Jitter 82ps At Termination impedance

90

100110

ps t PHLD Differenital Propagation Delay High to Low 1.0ns t PLHD Differential Propagation Delay Low to High 1.0ns t SKD Differential Skew | t PHLD - t PLHD

|25ps t PHZ Disable Time High to Z 5ns t PLZ Disable Time Low to Z 5t PZH Enable Time Z to High 1μs t PZL

Enable Time Z to Low

1

Notes:

1. For Max. or Min. conditions, use appropriate value speci ? ed under Electrical Characteristics for the applicable device type.

2. Typical values are at V DD =

3.3V , T A = 25°C ambient and maximum loading.

Notes:

1. For Max. or Min. conditions, use appropriate value speci ? ed under Electrical Characteristics for the applicable device type.

2. Typical values are at V DD =

3.3V , T A = 25°C ambient and maximum loading.

Power Supply Characteristics

Parameters Description

Test Conditions (1)

Min.

Typ.(2)Max.

Units I CC

Quiescent Power Supply Current

V DD = Max., V IN = V DD, OE = 'LOW'

1

mA

07-0013

元器件交易网

7PS8842E 01/18/07PI3HDMI412AD 1:2 Active HDMI Rev. 1.3 Compatible DeMux with

Advanced Re-Driver Functionality for Enhanced Signal Integrity

07-0013元器件交易网

8PS8842E 01/18/07PI3HDMI412AD 1:2 Active HDMI Rev. 1.3 Compatible DeMux with

Advanced Re-Driver Functionality for Enhanced Signal Integrity

Application Information (Please see application note for important design information.)

DVI TP2 (Tx) Compliance Test Setup

07-0013元器件交易网

9PS8842E 01/18/07PI3HDMI412AD 1:2 Active HDMI Rev. 1.3 Compatible DeMux with

Advanced Re-Driver Functionality for Enhanced Signal Integrity Pre-Emphasis Validation

De-Emphasis Validation

Measured at ouput DVI port, P3; Right eye is with pre-emphasis, left eye is without pre-emphasis Measured at ouput DVI port, P3; Right eye is with de-emphasis, left eye is without de-emphasis 07-0013元器件交易网

10PS8842E 01/18/07PI3HDMI412AD 1:2 Active HDMI Rev. 1.3 Compatible DeMux with

Advanced Re-Driver Functionality for Enhanced Signal Integrity Ordering Information

Ordering Code

Package Code Package Description PI3HDMI412ADZBE

ZB 56-pin, Pb-free & Green TQFN Notes:

? Thermal characteristics can be found on the company web site at /packaging/ ? E = Pb-free and Green

? Adding an X Suf ? x = Tape/Reel

Pericom Semiconductor Corporation ? 1-800-435-2336 ?

07-0013元器件交易网

本文来源：https://www.bwwdw.com/article/drf1.html