ASME标准目录（中英文对照） - 图文

ASME——美国机械工程师学会目录 编号 ANSI/ASME A 112.1.2-1991 ANSI/ASME A 112.14.3M-2000 ANSI/ASME A 112.14.4-2001 ANSI/ASME A 112.18.1M-1996 ANSI/ASME A 112.18.3M-1996 ANSI/ASME A 112.19.10-1994 ANSI/ASME A 112.19.14M-2001 ANSI/ASME A 112.19.1M-1994 ANSI/ASME A 112.19.2M-1998 ANSI/ASME A 112.19.3M-1987 管道系统中的空隙 油脂截止器 油脂去除装置 卫生设备配件 卫生设备配件中回流防护装置和系统操作要求 中文名称 英文名称 Air Gaps in Plumbing Systems Grease Interceptors Grease Removal Devices Plumbing Fixture Fittings Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings Dual Flush Devices for Water Closets Six Liter Water Closets Equipped with Dual Flushing Device Enameled Cast Iron Plumbing Fixtures Vitreous China Plumbing Fixtures Stainless Steel Plumbing Fixtures (Designed for Residential Use) 抽水马桶双冲装置 装有双冲水装置的6升抽水马桶 搪瓷铸铁卫生设备 瓷质卫生设备 不锈钢卫生设备(家用设计型) ANSI/ASME A 112.19.4M-1994 ANSI/ASME A 112.19.6-1995 ANSI/ASME A 112.19.7M-1995 ANSI/ASME A 112.19.8M-1987 ANSI/ASME A 112.19.9M-1991 ANSI/ASME A 112.21.1M-1991 ANSI/ASME A 112.21.3M-1976 ANSI/ASME A 112.3.1-1993 ANSI/ASME A 112.36.2M-1991 ANSI/ASME A 112.4.1-1993 ANSI/ASME A 搪瓷钢制卫生设备 马桶和小便池用冲水性能 涡流浴缸设备 Porcelain Enameled Formed Steel Plumbing Fixtures Hydraulic Performance Requirements for Water Closets and Urinals Whirlpool Bathtub Appliances Suction Fittings for Use in Swimming Pools, 游泳池、浅水池、矿泉池、热水浴池和涡流浴缸设备用Wading Pools, Spas, Hot Tubs, and Whirlpool 抽水配件 Bathtub Appliances 无釉层陶瓷卫生设备 地面排水管 公用事业的消火栓的使用和保养 Non-Vitreous Ceramic Plumbing Fixtures Floor Drains Hydrants for Utility and Maintenance Use Performance Standard and Installation 生活污水和化工污水地上和地下不锈钢排水系统的性Procedures for Stainless Steel Drainage Systems 能标准和安装程序 for Sanitary Storm and Chemical Application, Above and Below Ground 清除口 热水器排泄阀排水管 离地公用卫生设备的支撑架 Cleanouts Water Heater Relief Valve Drain Tubes Supports for Off-the-Floor Plumbing Fixtures 112.6.1M-1997 ANSI/ASME A 112.6.7-2001 ANSI/ASME A 120.1-2001 ANSI/ASME A 13.1-1996 ANSI/ASME A 17.1-1996 ANSI/ASME A 17.1a-2002 ANSI/ASME A 17.2-2001 ANSI/ASME A 17.2.3-1994 ANSI/ASME A 17.4-1991 ANSI/ASME A 17.5-1996 ANSI/ASME A 18.1b-2001 ANSI/ASME A 90.1-1997 ANSI/ASME 瓷漆的和环氧涂层的铸铁和PVC塑料卫生楼板污水池 建筑物维护的平台的安全要求 管道系统识别计划 电梯和自动扶梯安全规则 电梯和自动扶梯的安全规程 升降机、自动电梯和自动过道的检查指南 提升机和自动走道检验员手册 电梯乘客紧急撤离指南 电梯和自动扶梯电气设备 平台升降机和楼梯用椅式(乘人)升降机的安全标准 带式载人升降机的安全标准 管道系统中的气隙 for Public Use Enameled and Epoxy Coated Cast Iron and PVC Plastic Sanitary Floor Sinks Safety Requirements for Powered Platforms for Building Maintenance Scheme for the Identification of Piping Systems Elevators and Escalators, Safety Code for Safety Code for Elevators and Escalators Guide for Inspection of Elevators, Escalators, and Moving Walks Inspector-s Manual for Elevators and Moving Walks Guide for Emergency Evacuation of Passengers from Elevators Elevator and Escalator Electrical Equipment Safety Standard for Platform Lifts and Stairway Chairlifts Safety Standard for Belt Manlifts A112.1.2-2004 ANSI/ASME A112.1.2-2004 ANSI/ASME A112.14.1-1975 ANSI/ASME A112.18.1-2005 ANSI/ASME A112.18.1M-2003 ANSI/ASME A112.18.2-2005 ANSI/ASME A112.18.2M-2002 ANSI/ASME A112.18.3-2002 ANSI/ASME A112.18.6-2003 ANSI/ASME A112.19.10-2003 ANSI/ASME A112.19.14a-2003 ANSI/ASME A112.19.15-2005 管道系统中的气隙 回水阀 卫生管道配件 卫生设备配件 卫生管道用污水管配件 装修水管业用固定污水管配件 (Air Gaps in Plumbing Systems ) Backwater valves (Plumbing Fixture Fittings ) (Plumbing Fixture Waste Fittings ) (Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings ) (Flexible Water Connectors ) (Dual Flush Devices for Water Closets ) (Six-Liter Water Closets Equipped With A Dual Flushing Device ) 泵的固定配件中防逆流装置和系统的性能要求 柔性水管连接器 抽水马桶双冲装置 装有双冲水装置的6升抽水马桶 带压力密封门的浴池/旋涡浴池 ANSI/ASME A112.19.17-2002 ANSI/ASME A112.19.2-2003 ANSI/ASME A112.19.3-2002 ANSI/ASME A112.19.5-1979 ANSI/ASME A112.19.9M-2002 ANSI/ASME A112.20.1-2004 ANSI/ASME A112.20.2-2004 ANSI/ASME A112.4.14-2004 ANSI/ASME A112.4.14-2004 ANSI/ASME A112.4.7-2002 ANSI/ASME A112.6.4-2003 (Manufactured Safety Vacuum Release Systems 住宅和商用游泳池、健康中心、热浴盆和浅水池吸入系for Residential and Commercial Swimming Pool, 统用人造安全真空排放系统 Spas, Hot Tub and Wading Pool Suction Systems ) 瓷质卫生设备与小便池水和抽水马桶的水压要求 (Vitreous China Plumbing Fixtures and Hydraulic Requirements for Water Closets and Urinals ) (Stainless Steel Plumbing Fixtures (Designed for Residential Use) ) Trim for water-closet bowls, tanks, and urinals (dimensional standards) (Non-Vitreous Ceramic Plumbing Fixtures ) (Point of Use and Branch Water Sub-metering Systems ) (Roof, Deck, and Balcony Drains ) 不锈钢卫生设备(为住宅使用设计的) 抽水马桶、水箱和小便池的装修 无釉层陶瓷卫生设备 高纯度管道系统安装工的资格鉴定 管道系统用挡火物系统和设备的安装工资格鉴定 卫生管道系统中使用的手动直角转弯截止阀 卫生管道系统中使用的手动直角转弯截止阀 使用地点和支线分水表系统 房顶、地面和阳台排水管

ANSI/ASME A112.6.9-2005 ANSI/ASME A17.1-2004 ANSI/ASME A17.1-2004 ANSI/ASME A17.1a-2005 ANSI/ASME A17.1S-2005 ANSI/ASME A17.2-2004 ANSI/ASME A17.2-2004 ANSI/ASME A17.3-2002 ANSI/ASME A17.3-2005 ANSI/ASME A17.3-2005 ANSI/ASME A18.1-2003 ANSI/ASME A90.1-2003 虹吸式屋顶排水口 电梯和自动扶梯安全规则 电梯和自动扶梯安全规则 电梯和自动扶梯的安全规程 (Elevators and Escalators, Safety Code for ) ASME A17.1-2004升降机和自动电梯安全法则的附录 升降机、自动电梯和自动走道的检查指南 升降机、自动电梯和自动走道的检查指南 现有电梯和自动扶梯的安全指南 现有电梯和自动扶梯的安全法则 现有电梯和自动扶梯的安全法则 平台式升降机和扶梯式升降椅的安全标准 带式载人升降机的安全标准 (Safety Code for Existing Elevators and Escalators ) (Safety Standard for Platform Lifts and Stairway Chairlifts ) (Safety Standard for Belt Manlifts ) ANSI/ASME AG-1-1994 ANSI/ASME AG-1-2003 ANSI/ASME AG-1a-2004 ANSI/ASME B 1.10M-1997 ANSI/ASME B 1.12-1987 ANSI/ASME B 1.13M-1995 ANSI/ASME B 1.16M-1984 ANSI/ASME B 1.2-1983 ANSI/ASME B 1.20.1-1983 ANSI/ASME B 1.20.5-1991 ANSI/ASME B 1.20.7-1991 ANSI/ASME B 1.21M-1997 核空气和气体处理规程 核空气和气体处理法规 核气体和气体处理法规 统一微型螺纹 螺纹.五级接口.配合螺纹 M型米制螺纹 M型米制螺纹的量规和测量 统一螺纹的量规和测量 通用的管螺纹(英制) 干密封管螺纹的测量(英制) 英制软管连接螺纹 米制螺纹.MJ牙形 Nuclear Air and Gas Treatment, Code on (Nuclear Air and Gas Treatment, Code on ) Unified Miniature Screw Threads Screw Threads - Class 5 Interference - Fit Thread Metric Screw Threads - M Profile Gages and Gaging for Metric M Screw Threads Gages and Gaging for Unified Screw Threads Pipe Threads, General Purpose (Inch) Gaging for Dryseal Pipe Threads (Inch) Hose Coupling Screw Threads - Inch Metric Screw Threads - MJ Profile ANSI/ASME B 1.22M-1985 ANSI/ASME B 1.30M-1992 ANSI/ASME B 1.3M-1992 ANSI/ASME B 1.5-1997 ANSI/ASME B 1.7M-1984 ANSI/ASME B 1.8-1988 ANSI/ASME B 107.1-1993 ANSI/ASME B 107.10M-1996 ANSI/ASME B 107.11M-1993 ANSI/ASME B 107.12-1997 ANSI/ASME B 107.13M-1996 ANSI/ASME B MJ系列米制螺纹用量规和测量规程 螺纹尺寸计算和圆整规则 英制和米制螺纹尺寸螺纹测量系统 Gages and Gaging Practice for MJ Series Metric Screw Threads Screw Threads - Practice for Calculating and Rounding Dimensions Screw Thread Gaging Systems for Dimensional Acceptability - Inch and Metric Screw Threads (UN, UNR, UNJ, M, and MJ) Acme Screw Threads Screw Threads, Nomenclature, Definitions, and Letter Symbols for Stub Acme Screw Threads Socket Wrenches, Hand (Inch Series) Handles and Attachments for Hand Socket Wrenches - Inch and Metric Series Pliers, Diagonal Cutting, and Nippers, End Cutting Nut Drivers (Spin Type, Screwdriver Grip) (Inch Series) Pliers - Long Nose, Long Reach Hand Torque Tools ACME螺纹 螺纹的术语、定义和字母代号 短齿梯形螺纹 手动套筒扳手(英制) 英制和米制手动套筒扳手的手柄及附件 斜嘴剪丝钳和中心剪丝钳 螺母旋具(旋转型旋具夹紧器)(英制) 尖嘴长臂钳 手动扭矩工具 107.14M-1994 ANSI/ASME B 107.15-1993 ANSI/ASME B 107.16M-1998 ANSI/ASME B 107.17M-1997 ANSI/ASME B 107.18M-1996 ANSI/ASME B 107.19-1993 ANSI/ASME B 107.2-1995 ANSI/ASME B 107.20M-1992 ANSI/ASME B 107.21-1992 ANSI/ASME B 107.22M-1991 ANSI/ASME B 107.23M-1997 ANSI/ASME B 107.25M-1996 一字和十字槽螺钉旋具 台式及手动金属切割剪 扳手开口度标准量规 老虎钳(克丝钳) 扣环钳 电动冲击式延伸、接合及万向接头套筒扳手(英制) Flat-Tip and Phillips Screwdrivers Shears (Metal Cutting, Bench, and Hand) Gages, Wrench Openings, Reference Pliers (Wire Twister) Pliers, Retaining Ring Socket Wrenches, Extensions, Adaptors, and Universal Joints, Power Drive (Impact) (Inch Series) Pliers (Lineman-s, Iron Worker-s, Gas, Glass, and Fence) Wrench, Crowfoot Attachments Electronic Cutters and Pliers Pliers, Multiple Position, Adjustable Pliers - Performance Test Methods 线路工、打铁工、煤气工、玻璃工和篱笆工用钳 扳手及爪形附件 电子切削工具和电子钳 多位可调钳 老虎钳.性能试验方法 ANSI/ASME B 107.27-1996 ANSI/ASME B 107.28M-1997 ANSI/ASME B 107.31M-1997 ANSI/ASME B 107.34M-1997 ANSI/ASME B 107.35M-1997 ANSI/ASME B 107.38M-1998 ANSI/ASME B 107.41M-1997 ANSI/ASME B 107.42M-1997 ANSI/ASME B 107.43M-1998 ANSI/ASME B 107.44M-1998 ANSI/ASME B 107.45M-1998 ANSI/ASME B 107.46M-1998 多位钳(电连接头) 电子转距仪器 十字槽计量标准旋具 火花塞用套筒扳手 螺母旋具(旋转型旋具)(米制系列) 电子钳 羊角锤.安全要求 手斧.安全要求 木材劈裂楔.安全要求 玻璃匠凿和木工凿.安全要求 细长凿和地板/电工用凿.安全要求 双头螺栓、螺钉和管道提取器.安全要求 Pliers, Multiple Position (Electrical Connector) Electronic Torque Instruments Screwdriver, Cross Tip Gaging Standard Socket Wrenches for Spark Plugs Nut Drivers (Spin Type, Screwdriver Grip) (Metric Series) Electronic Pliers Nail Hammers - Safety Requirements Hatchets - Safety Requirements Wood Splitting Wedges - Safety Requirements Glaziers- Chisels and Wood Chisels - Safety Requirements Ripping Chisels and Flooring/Electricians- Chisels - Safety Requirements Stud, Screw and Pipe Extractors - Safety Requirements

ANSI/ASME B 107.47M-1998 ANSI/ASME B 107.49M-1998 ANSI/ASME B 107.4M-1995 ANSI/ASME B 107.50M-1998 ANSI/ASME B 107.52M-1998 ANSI/ASME B 107.53M-1998 编号 ANSI/ASME B 107.54-2001 ANSI/ASME B 107.5M-1994 ANSI/ASME B 107.6-1994 ANSI/ASME B 107.8M-1996 ANSI/ASME B 107.9M-1994 ANSI/ASME B 金属凿子 钉子.安全要求 便携式手动、气动和电动工具用驱动和从动端 手工工具.修砖錾和砌砖.安全要求 拔钉器棒.安全要求 手工工具.圆头锤.安全要求 中文名称 重型铸造工具.安全要求 手持式套筒扳手(米制) 组合开端套筒扳手和联接螺母(英制) 调节扳手 组合开端套筒扳手和联接螺母(米制系列) 燃气轮机.采购标准.维修和安全 Metal Chisels Nail Sets - Safety Requirements Driving and Spindle Ends for Portable Hand, Air, and Electric Tools Hand Tools - Brick Chisels and Brick Sets - Safety Requirements Nail-Puller Bars - Safety Requirements Hand Tools - Ball Peen Hammers - Safety Requirements 英文名称 Heavy Striking Tools - Safety Requirements Socket Wrenches, Hand (Metric Series) Wrenches, Box, Open End, Combination, and Flare Nut (Inch Series) Adjustable Wrenches Wrenches, Box, Open End, Combination, and Flare Nut (Metric Series) Gas Turbines - Procurement Standard - 133.12-1981 ANSI/ASME B 133.16-1978 ANSI/ASME B 133.4-1978 ANSI/ASME B 133.5-1978 ANSI/ASME B 133.7M-1985 ANSI/ASME B 133.8M-1977 ANSI/ASME B 133.9-1994 ANSI/ASME B 15.1-1996 ANSI/ASME B 16.1-1989 ANSI/ASME B 16.10-1992 ANSI/ASME B 16.11-1996 ANSI/ASME B 16.12-1991 ANSI/ASME B 燃气轮机在航海上的应用 燃气轮机的控制和保护系统 燃气轮机的电气设备 燃气轮机的燃料 燃气轮机装置噪音释放 固定式燃气轮机发动机的废气排放测量 机械动力传输设备的安全性标准 25,125,250和800级铸铁管法兰和法兰配件 阀门的面对面及端对端尺寸 锻制配件、承插焊接配件及螺纹配件 铸铁螺纹排水配件 带有管螺纹的铁管塞、管套及防松螺母 Maintenance and Safety Marine Applications, Gas Turbine Control and Protection Systems, Gas Turbine Electrical Equipment, Gas Turbine Fuels, Gas Turbine Installation Sound Emission, Gas Turbine Measurement of Exhaust Emissions from Stationary Gas Turbine Engines Safety Standard for Mechanical Power Transmission Apparatus, Cast Iron Pipe Flanges and Flanged Fittings, Class 25, 125, 250, and 800 Face-to-Face and End-to-End Dimensions of Valves Forged Fittings, Socket-Welding and Threaded Cast Iron Threaded Drainage Fittings Ferrous Pipe Plugs, Bushing, and Locknuts 16.14-1991 ANSI/ASME B 16.15-1985 ANSI/ASME B 16.20-1993 ANSI/ASME B 16.21-1992 ANSI/ASME B 16.22-2001 ANSI/ASME B 16.23-2002 ANSI/ASME B 16.24-2001 ANSI/ASME B 16.25-1997 ANSI/ASME B 16.28-1994 ANSI/ASME B 16.29-2001 ANSI/ASME B 16.3-1992 ANSI/ASME B 16.33-1990 ANSI/ASME B 125级和250级青铜铸造螺纹配件 管法兰用金属垫圈螺旋缠绕和套封环形接头 管法兰用非金属平垫圈 锻铜和铜合金钎焊压力配件 DWV铸铜合金钎焊连接排水配件 铸铜合金管法兰和法兰配件 对焊端部 锻钢焊接圆形弯头和回转管 DWV型锻铜和锻铜合金钎焊排水配件 可锻铸铁螺纹配件 125表压以下的气体管道系统中使用的手动金属气阀门 端部有凸缘、有螺纹和焊接的阀 with Pipe Threads Cast Bronze Threaded Fittings, Classes 125 and 250 Metallic Gaskets for Pipe Flanges - Ring Joint, Spiral Wounds and Jacketed Nonmetallic Flat Gaskets for Pipe Flanges Wrought Copper and Copper Alloy Solder-Joint Pressure Fittings Cast Copper Alloy Solder Joint Drainage Fittings - DWV Cast Copper Alloy Pipe Flanges and Flanged Fittings Buttwelding Ends Wrought Steel Buttwelding Short Radius Elbows and Returns Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings - DWV Malleable-Iron Threaded Fittings Manually Operated Metallic Gas Valves for Use in Gas Piping Systems up to 125 psig Valves - Flanged, Threaded and Welding End 16.34-1996 ANSI/ASME B 16.36-1996 ANSI/ASME B 16.38-1985 ANSI/ASME B 16.39-1986 ANSI/ASME B 16.4-1992 ANSI/ASME B 16.40-2002 ANSI/ASME B 16.42-1987 ANSI/ASME B 16.44-1995 ANSI/ASME B 16.44a-1997 ANSI/ASME B 16.45-1987 ANSI/ASME B 16.47-1996 ANSI/ASME B 16.48-1997 孔板计法兰 Orifice Flanges Large Metallic Valves for Gas Distribution 大型手动气分配系统用金属阀(NPS 2 1/2到12,压力不(Manually Operated, NPS 2 1/2 to 12, 125 psig 超过125表压) Maximum) 锻铁螺纹管活接头 灰口铁螺纹配件 气分配系统中手动热塑气截流阀及阀门 球墨铸铁管法兰和法兰配件 家庭管道系统使用的手工操作的金属气体阀门 家庭管道系统中用的手动金属气阀 Soventr排水系统中铸铁配件 大直径钢法兰NPS26至60 钢线坯 Pipe Unions, Malleable Iron Threaded Gray Iron Threaded Fittings Gas Shut-Offs and Valves in Gas Distribution Systems, Manually Operated Thermoplastic Ductile Iron Pipe Flanges and Flanged Fittings Manually Operated Metallic Gas Valves for Use in House Piping Systems Manually Operated Metallic Gas Valves for Use in House Piping Systems Cast Iron Fittings for Soventr Drainage Systems Large Diameter Steel Flanges NPS 26 Through NPS 60 Steel Line Blanks ANSI/ASME B 16.5-1996 ANSI/ASME B 16.50-2001 ANSI/ASME B 16.9-1993 ANSI/ASME B 18.1.1-1972 ANSI/ASME B 18.1.2-1972 ANSI/ASME B 18.1.3M-1983 ANSI/ASME B 18.10-1982 ANSI/ASME B 18.12-2001 ANSI/ASME B 18.13-1996 ANSI/ASME B 18.13.1M-1991 ANSI/ASME B 18.15-1985 ANSI/ASME B 18.15.2-1998 管法兰及法兰配件NPS1/2至24 锻造铜及铜合金钎焊压力配件 工厂制锻钢对焊配件 小型固体铆钉(7/16英寸标称直经和更小) 大型铆钉(1/2英寸标称直径和更大) 米制小型实心铆钉 轨道螺栓及螺母 机械紧固件的术语集 英制SEMS螺钉和垫圈组件 米制SEMS螺钉和垫圈组件 锻造的环首螺栓 米制直杆提升孔 Pipe Flanges and Flanged Fittings NPS 1/2 Through NPS 24 Wrought Copper and Copper Alloy Braze-Joint Pressure Fittings Factory-Made Wrought Steel Buttwelding Fittings Small Solid Rivets (7/16 Inch Nominal Diameter and Smaller) Large Rivets (1/2 Inch Nominal Diameter and Larger) Metric Small Solid Rivets Track Bolt and Nuts Mechanical Fasteners, Glossary of Terms for Screw and Washer Assemblies - SEMS (Inch Series) Screws and Washer Assemblies - SEMS (Metric Series) Forged Eyebolts Metric Straight Shank Lifting Eyes

ANSI/ASME B 18.16.1M-1979 ANSI/ASME B 18.16.2M-1979 ANSI/ASME B 18.18.1M-1987 ANSI/ASME B 18.18.2M-1987 ANSI/ASME B 18.18.3M-1987 ANSI/ASME B 18.18.4M-1987 ANSI/ASME B 18.18.5M-1998 ANSI/ASME B 18.18.6M-1998 ANSI/ASME B 18.18.7M-1998 ANSI/ASME B 18.2.1-1996 ANSI/ASME B Hex Nuts and Hex Flange Nuts, Mechanical and 六角型螺母和六角型法兰螺母,米制普通扭力型钢机械Performance Requirements for Prevailing-Torque 和操作要求 Type Steel, Metric Hex Nuts and Hex Flange Nuts, Torque-Tension 六角型螺母和六角型法兰螺母, 米制普通扭力型钢扭Test Requirements for Prevailing-Torque Type 力矩拉力测试要求 Steel, Metric 一般用途紧固件的质量保证和检验 高容量机器组装紧固件的质量保证和检验 特殊用途紧固件的质量保证和检验 General Purpose Fasteners, Inspection and Quality Assurance for Machine Assembly Fasteners, Inspection and Quality Assurance for High Volume Special Purpose Fasteners, Inspection and Quality Assurance for Fasteners for Highly Specialized Engineered Applications, Inspection and Quality Assurance for Inspection and Quality Assurance Plan Requiring In Process Inspection and Controls Quality Assurance Plan for Fasteners Produced in a Third Party Accreditation System Quality Assurance Plan for Fasteners Produced in a Customer Approved Control Plan Square and Hex Bolts and Screws (Inch Series) Square and Hex Nuts (Inch Series) 高度专业化工程应用的紧固件的质量保证和检验 过程检验和控制的检验和质量保证计划要求 由第三方认可系统提供的紧固件质量保证规划 用户验收控制规划中提供的紧固件的质量保证规划 四方和六角形螺栓和螺钉(英寸系列) 英制系列四角和六角螺帽 18.2.2-1987 ANSI/ASME B 18.2.3.10M-1996 ANSI/ASME B 18.2.3.1M-1979 ANSI/ASME B 18.2.3.2M-1979 ANSI/ASME B 18.2.3.3M-1979 ANSI/ASME B 18.2.3.4M-1984 ANSI/ASME B 18.2.3.5M-1979 ANSI/ASME B 18.2.3.6M-1979 ANSI/ASME B 18.2.3.7M-1979 ANSI/ASME B 18.2.3.9M-1984 ANSI/ASME B 18.2.4.1M-2002 ANSI/ASME B 18.2.4.2M-1979 ANSI/ASME B 四方头螺栓(米制系列) 螺钉,米制六角型螺帽 螺钉,米制六角型 螺钉, 米制重六角型 米制六角头法兰螺钉 螺栓, 米制六角型 螺栓, 米制重六角型 螺栓, 米制重六角型结构 米制加重六角头带法兰螺钉 1型米制六角螺母 六角型螺母,2型,米制 六角型螺母,有槽缝,米制 Square Head Bolts (Metric Series) Screws, Metric Hex Cap Screws, Metric Formed Hex Screws, Metric Heavy Hex Screws, Metric Hex Flange Bolts, Metric Hex Bolts, Metric Heavy Hex Bolts, Metric Heavy Hex Structural Metric Heavy Hex Flange Screws Hex Nuts, Style 1, Metric Hex Nuts, Style 2, Metric Hex Nuts, Slotted, Metric 18.2.4.3M-1979 ANSI/ASME B 18.2.4.5M-1979 ANSI/ASME B 18.2.4.6M-1979 ANSI/ASME B 18.2.6-1996 ANSI/ASME B 18.2.7.1M-2002 ANSI/ASME B 18.21.1-1994 ANSI/ASME B 18.21.2M-1994 ANSI/ASME B 18.22.1-1965 ANSI/ASME B 18.24.1-1996 ANSI/ASME B 18.24.3-1998 ANSI/ASME B 18.25.1M-1996 ANSI/ASME B 18.25.2M-1996 ANSI/ASME B 六角卡住螺母,米制 重型六角螺母,米制 结构应用中使用的固定器 米制12-花键法兰螺钉 锁紧垫圈(英寸系列) 锁紧垫圈(米制系列) 水平垫圈 B18外螺纹产品部分鉴定(PIN)编码系统标准 B18非螺纹产品部分识别数字编码系统 四方型和矩型键和键槽 半圆键和键槽 Hex Jam Nuts, Metric Hex Nuts, Heavy, Metric Fasteners for Use in Structural Applications Metric 12-Spline Flange Screws Lock Washers (Inch Series) Lock Washers (Metric Series) Plain Washers Part Identifying Number (PIN) Code System Standard for B18 Externally Threaded Products Part Identifying Number (PIN) Code System Standard for B18 Non-Threaded Products Square and Rectangular Keys and Keyways Woodruff Keys & Keyways 四方形和矩形键和键槽.宽度公差和大于基本尺寸的变 Square and Rectangular Keys and Keyways - 18.25.3M-1998 ANSI/ASME B 18.27.1-1998 化 Width Tolerances and Deviations Greater than Basic Size Tapered and Reduced Cross Section Retaining Rings (Inch Series) (External Type - NA1; Internal Type - NA2; E-Ring Type - NA3) Tapered and Reduced Cross Section External Retaining Rings (Inch Series) (Heavy Duty External - NA4; Reinforced E Rings - NA5; C Type Rings - NA6) Tapered and Reduced Cross Section Retaining Rings (Inch Series) (Bowed External-NA7; Bowed Internal-NA8; Bowed External E-NA9) Helical Coil Screw Thread Inserts - Free Running and Screw Locking (Inch Series) Socket Cap, Shoulder, and Set Screws (Inch Series) Screws, Socket Head Cap (Metric Series) Keys and Bits, Hexagon (Metric Series) Hexagon Socket Head Shoulder Screws (Metric Series) Screws, Hexagon Socket Button Head Cap (Metric Series) 锥形渐减交叉档圈(英寸系列) ANSI/ASME B 18.27.2-1998 ANSI/ASME B 18.27.3-1998 ANSI/ASME B 18.29.1-1993 ANSI/ASME B 18.3-1998 ANSI/ASME B 18.3.1M-1986 ANSI/ASME B 18.3.2M-1979 ANSI/ASME B 18.3.3M-1986 ANSI/ASME B 18.3.4M-1986 锥形渐减交叉外档圈(英寸系列) 锥形渐减交叉外档圈(英寸系列) 空转的和螺钉锁定的英制螺旋线圈螺钉用螺纹垫片 六角键和花键圆柱头有肩定位螺钉 米制系列内六角螺钉 六角钻头(米制系列) 米制系列内六角轴肩螺钉 米制系列内六角圆头螺钉 ANSI/ASME B 18.3.5M-1986 ANSI/ASME B 18.3.6M-1986 ANSI/ASME B 18.5-1990 ANSI/ASME B 18.5.2.1M-1996 ANSI/ASME B 18.5.2.2M-1982 ANSI/ASME B 18.5.2.3M-1990 ANSI/ASME B 18.6.1-1981 ANSI/ASME B 18.6.2-1995 ANSI/ASME B 18.6.3-1972 ANSI/ASME B 18.6.4-1998 ANSI/ASME B 18.6.5M-1986 ANSI/ASME B 18.6.7M-1985 米制系列内六角扁平沉头螺钉 米制系列内六角紧定螺钉 园头螺栓(英寸系列) 螺栓,米制园头短四方杆 米制圆头方颈螺栓 米制大圆头方颈螺栓 木螺丝(英寸系列) Hexagon Socket Flat Countersunk Head Cap Screws (Metric Series) Screws, Hexagon Socket Set (Metric Series) Round Head Bolts (Inch Series) Bolts, Metric Round Head Short Square Neck Bolts, Metric Round Head Square Neck Round Head Square Neck Bolts With Large Head (Metric) Wood Screws (Inch Series) 槽缝头帽螺钉,四角型头配套螺钉,和槽缝非头状配套 Slotted Head Cap Screws, Square Head Set 螺钉 Screws, and Slotted Headless Set Screws 有狭槽和凹口头的机床螺钉和螺母 成型或切割形成螺纹的螺钉,攻丝金属,英寸系列 米制自攻螺钉和攻丝自攻螺钉 米制机用螺钉 Slotted and Recessed Head Machine Screws and Machine Screw Nuts Screws, Tapping and Metallic Drive, Inch Series, Thread Forming and Cutting Metric Thread Forming and Thread Cutting Tapping Screws Metric Machine Screws

ANSI/ASME B 18.7-1972 ANSI/ASME B 18.7.1M-1984 ANSI/ASME B 18.8.1-1994 ANSI/ASME B 18.8.2-1995 ANSI/ASME B 18.8.3M-1995 ANSI/ASME B 18.8.4M-1994 ANSI/ASME B 18.8.5M-1994 ANSI/ASME B 18.8.6M-1995 ANSI/ASME B 18.8.7M-1994 ANSI/ASME B 18.8.8M-1994 ANSI/ASME B 18.8.9M-1998 编号 ANSI/ASME B 半管形铆钉,全管型铆钉,分裂式铆钉和铆钉帽,一般目 Semi-Tubular Rivets, Full Tubular Rivets, 的 Split Rivets and Rivet Caps, General Purpose 米制通用半管形铆钉 U形夹销和开尾销(英寸系列) 锥形销、定位销、直销、有槽销和弹簧销(英制系列) 米制系列螺旋弹簧销 有槽弹簧销(米制系列) 机器榫钉.硬质的(米制系列) 米制系列开尾销 无头U形夹销(米制系列) 有夹U形夹销(米制系列) 带槽的销子.米制系列 中文名称 犁头螺栓 Rivets, Metric General Purpose Semi-Tubular Clevis Pins and Cotter Pins (Inch Series) Taper Pins, Dowel Pins, Straight Pins, Grooved Pins, and Spring Pins (Inch Series) Spring Pins - Coiled Type (Metric Series) Spring Pins - Slotted (Metric Series) Machine Dowel Pins - Hardened Ground (Metric Series) Cotter Pins, Metric Series Headless Clevis Pins (Metric Series) Headed Clevis Pins (Metric Series) Grooved Pins Metric Series 英文名称 Plow Bolts (Inch Series) 18.9-1996 ANSI/ASME B 19.1-1995 ANSI/ASME B 19.3-1991 ANSI/ASME B 20.1-1996 ANSI/ASME B 29.10M-1997 ANSI/ASME B 29.11M-1994 ANSI/ASME B 29.12M-1997 ANSI/ASME B 29.14M-1996 ANSI/ASME B 29.15M-1997 ANSI/ASME B 29.17M-1983 ANSI/ASME B 29.19M-1996 ANSI/ASME B 29.200-2001 ANSI/ASME B 空气压缩机系统的安全标准 加工工业用压缩机的安全标准 输送机及其相关设备的安全标准 重型旁置外链片传动链和链齿 组合链、附件及链齿 钢套筒无滚子链、附件及链齿 H型碾磨链、附件及链齿 钢辊型传送链、附件和链齿 绞接式平顶输送机链和链齿 农用滚子链、附件和链轮 焊接钢型轧链条.焊接钢牵引链.附件和链轮齿 Safety Standard for Air Compressor Systems Safety Standard for Compressors for Process Industries Safety Standard for Conveyors and Related Equipment Heavy Duty Offset Sidebar Transmission Roller Chains and Sprocket Teeth Combination Chains, Attachments, and Sprocket Teeth Steel Bushed Rollerless Chains, Attachments, and Sprocket Teeth H Type Mill Chains, Attachments, and Sprocket Teeth Steel Roller Type Conveyor Chains, Attachments, and Sprocket Teeth Hinge Type Flat Top Conveyor Chains and Sprocket Teeth Agricultural Roller Chains, Attachments, and Sprockets Welded Steel Type Mill Chains, Welded Steel Drag Chains, Attachments and Sprocket Teeth 水、污水处理设备用700级焊接钢和铸造链、附件及链 700 Class Welded Steel and Cast Chains, 29.21M-1996 ANSI/ASME B 29.22M-1995 ANSI/ASME B 29.23M-1985 ANSI/ASME B 29.24M-1995 ANSI/ASME B 29.25M-1994 ANSI/ASME B 29.26M-1996 ANSI/ASME B 29.6M-1993 ANSI/ASME B 30.1-1998 ANSI/ASME B 30.10-1993 ANSI/ASME B 30.11-1998 ANSI/ASME B 30.12-2001 ANSI/ASME B 30.13-1996 轮 锻造的无铆钉链、链齿传动链和传动支架 柔性链联接器 高架提升机用滚子载重链 开口桶形钢制斜栓节传送链、附件及链轮 动力传动滚子链的疲劳试验 钢制活络链、附件和链轮 千斤顶 吊钩 单轨起重机和悬挂式桥吊 旋翼机悬吊货物装卸荷载 储存和回收(S/R)机械及辅助设备 Attachments, and Sprockets for Water and Sewage Treatment Plants Drop Forged Rivetless Chains, Sprocket Teeth Drive Chain/Drive Dogs Flexible Chain Couplings Roller Load Chains for Overhead Hoists Open Barrel Steel Pintle-Type Conveyor Chains, Attachments, and Sprockets Fatigue Testing Power Transmission Roller Chain Steel Detachable Link Chains, Attachments, and Sprockets Jacks Hooks Monorails and Underhung Cranes Handling Loads Suspended from Rotorcraft Storage/Retrieval (S/R) Machines and Associated Equipment ANSI/ASME B 30.14-1996 ANSI/ASME B 30.16-1993 ANSI/ASME B 30.16a-2001 ANSI/ASME B 30.17-1998 ANSI/ASME B 30.18-1993 ANSI/ASME B 30.19-1993 ANSI/ASME B 30.2-2001 ANSI/ASME B 30.20-1993 ANSI/ASME B 30.20a-2001 ANSI/ASME B 30.21-1994 ANSI/ASME B 30.22-1993 侧臂式拖拉机的安全标准 高架悬挂提升机 悬吊提升机(悬) 高架和龙门起重机(单梁顶行桥架悬挂提升机) 堆垛用起重机(多梁顶行或底行桥架悬挂式提升机) 索道 Safety Standard for Side Boom Tractors Overhead Hoists (Underhung) Overhead Hoists (Underhung) Overhead and Gantry Cranes (Top Running Bridge, Single Girder, Underhung Hoist) Stacker Cranes (Top or Under Running Bridge, Multiple Girder with Top or Under Running Trolley Hoist) Cableways Overhead and Gantry Cranes (Top Running 高架和龙门起重机(单梁或多梁顶行桥架、顶行起重机) Bridge, Single or Multiple Girder, Top Running Trolley Hoist) 下吊钩提升装置 钩在下提升装置 手动操作杆式提升机 活节悬臂起重机 Below-the-Hook Lifting Devices Below-the-Hook Lifting Devices Manually Lever Operated Hoists Articulating Boom Cranes ANSI/ASME B 30.25-1998 ANSI/ASME B 30.3-1996 ANSI/ASME B 30.4-1990 ANSI/ASME B 30.5-1994 ANSI/ASME B 30.5a-2002 ANSI/ASME B 30.6-1995 ANSI/ASME B 30.7-1994 ANSI/ASME B 30.8-1993 ANSI/ASME B 30.9-1996 ANSI/ASME B 31.1-2001 ANSI/ASME B 31.3-2002 ANSI/ASME B 31.4-1992 废料和物料装卸搬运设备 施工用塔式起重机 龙门座起重机、塔式起重机和转柱起重机 汽车起重机和机车起重机 移动式起重机和机车起重机 桅杆起重机 基座固定卷筒提升机 水上起重机和水上桅杆起重机 吊索 动力管道 工艺管道 烃类、液化石油气、无水氨和醇类用液体输送系统 Scrap and Material Handlers Construction Tower Cranes Portal, Tower, and Pedestal Cranes Mobile and Locomotive Cranes Mobile and Locomotive Cranes Derricks Base Mounted Drum Hoists Floating Cranes and Floating Derricks Slings Power Piping Process Piping Liquid Transportation Systems for Hydrocarbons, Liquid Petroleum Gas, Anhydrous

Ammonia, and Alcohols ANSI/ASME B 31.4a-2001 ANSI/ASME B 31.5-2001 ANSI/ASME B 31.8-1995 ANSI/ASME B 31.8S-2002 ANSI/ASME B 31.9-1996 ANSI/ASME B 31G-1991 ANSI/ASME B 32.3M-1984 ANSI/ASME B 32.6M-1984 ANSI/ASME B 36.10M-1996 ANSI/ASME B 36.19M-1985 ANSI/ASME B 40.1-1991 ANSI/ASME B 液烃和其他液体用管道输送系统 制冷管道 气体输送和分配管道系统 气体管道的管理系统完整性 建筑物服务设施用压力管道标准 用于测定受腐蚀管道剩余强度的手册 板状金属制品的优选米制尺寸 Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids Refrigeration Piping Gas Transmission and Distribution Piping Systems Managing System Integrity of Gas Pipelines Building Services Piping Code for Pressure Piping Manual for Determining the Remaining Strength of Corroded Pipelines Metric Sizes for Flat Metal Products, Preferred 除管道外的管形金属制品与英制尺寸相当的优选米制 Tubular Metal Products Other Than Pipe, 尺寸 Preferred Metric Equivalents of Inch Sizes for 焊接锻钢管和无缝锻钢管 不锈钢管 量规.压力刻度指示表.弹性件 隔膜式密封件 Welded and Seamless Wrought Steel Pipe Stainless Steel Pipe Gauges - Pressure Indicating Dial Type - Elastic Element Diaphragm Seals 40.2-1991 ANSI/ASME B 40.200-2001 ANSI/ASME B 40.3-1997 ANSI/ASME B 40.5-1995 ANSI/ASME B 40.6-1994 ANSI/ASME B 46.1-2002 ANSI/ASME B 47.1-1988 ANSI/ASME B 5.10-1994 ANSI/ASME B 5.18-1972 ANSI/ASME B 5.1M-1985 ANSI/ASME B 5.35-1983 ANSI/ASME B 5.49-1998 ANSI/ASME B 直接读和远读的量热仪 双金属精密温度计 减震器 限压阀 表面特征(表面粗糙度、波纹度和扭转度) 量规半成品 机用锥销(自动夹紧型和大锥度序列) 铣床用主轴端和刀柄 T型槽.T型槽螺栓、螺母和榫舌 砂轮和碟形砂轮机安装规范 强压机术语集 带有自动更换工具的机床用V形凸缘工具柄 Thermometers, Direct Reading and Remote Reading Bimetallic Actuated Thermometers Snubbers Pressure Limiter Valves Surface Texture (Surface Roughness, Waviness, and Lay) Gage Blanks Machine Tapers (Self Holding and Steep Taper Series) Spindle Noses and Tool Shanks for Milling Machines T-Slots - Their Bolts, Nuts, and Tongues Machine Mounting Specifications for Abrasive Discs and Plate Mounted Wheels Press Terms, Glossary of Mechanical V Flange Tool Shanks for Machining Centers 5.50-1994 ANSI/ASME B 5.51M-1979 ANSI/ASME B 5.54-1992 ANSI/ASME B 5.55M-1994 ANSI/ASME B 5.56M-1994 ANSI/ASME B 5.57-1998 ANSI/ASME B 56.1-1993 ANSI/ASME B 56.10-1992 ANSI/ASME B 56.11.1-1992 ANSI/ASME B 56.11.4-1992 ANSI/ASME B 56.11.5-1992 机床的优选SI单位 计算机数字控制的机床性能评测 with Automatic Tool Changers Preferred Sl Units for Machine Tools Performance Evaluation of Computer Numerically Controlled Machining Centers, Methods for Specification and Performance Standard, Power Press Brakes Specification and Performance Standard, Power Shears Methods for Performance Evaluation of Computer Numerically Controlled Lathes and Turning Centers Low Lift and High Lift Trucks Manually Propelled High Lift Industrial Trucks, Safety Standard for Double Race or Bi-Level Swivel and Rigid Industrial Casters Hook-Type Forks and Fork Carriers for Powered Industrial Forklift Trucks Measurement of Sound Emitted by Low Lift, High Lift, and Rough Terrain Powered Industrial Trucks 机动压弯机规范和性能标准 动力剪切机规范和性能标准 计算机数控机床和回转中心的性能评价方法 低提升和高提升的装卸车 人工操作高提升工业装卸车的安全标准 双轮或双层旋转和刚性工业用脚轮 机动工业叉车用吊钩式叉头和叉架 低提升、高提升和不平地机动工业货车噪音测量 ANSI/ASME B 56.11.6-1996 ANSI/ASME B 56.11.7-1998 ANSI/ASME B 56.5-1993 ANSI/ASME B 56.7-1987 ANSI/ASME B 56.8-1993 ANSI/ASME B 56.9-1992 ANSI/ASME B 73.1M-2001 ANSI/ASME B 73.2M-1991 ANSI/ASME B 73.3M-1997 ANSI/ASME B 73.5M-1995 ANSI/ASME B 机动工业货车上能见度的评定 Evaluation of Visibility from Powered Industrial Trucks Liquid Propane Gas (LPG) Fuel Cylinders 液化丙烷气(LPG)燃料缸(水平或垂直)安装.机动工业(Horizontal or Vertical) Mounting - Liquid 货车的液体排出量 Withdrawal for Powered Industrial Trucks Safety Standard for Guided Industrial 工业轨道式车辆的安全标准和载人工业车辆自动化功Vehicles and Automated Functions of Manned 能 Industrial Vehicles 工业汽车式起重机 人和料运载工具的安全标准 人工操作的工业牵引车安全标准 化工用卧式端吸离心泵规范 化工用立式直列式离心泵规范 化工用不密封卧式端吸离心泵规范 Industrial Crane Trucks Safety Standard for Personnel and Burden Carriers Safety Standard for Operator Controlled Industrial Tow Tractors Horizontal End Suction Centrifugal Pumps for Chemical Process, Specifications for Vertical In-Line Centrifugal Pumps for Chemical Process, Specifications for Specification for Sealless Horizontal End Suction Centrifugal Pumps for Chemical Process Specification for Thermoplastic and 化工用热塑和热固性聚合材料制卧式端吸离心泵规范 Thermoset Polymer Material Horizontal End Suction Centrifugal Pumps for Chemical Process 千分表(线性测量用) Dial Indicators (for Linear Measurements) 89.1.10M-1987 ANSI/ASME B 89.1.13-2001 ANSI/ASME B 89.1.17-2001 ANSI/ASME B 89.1.2M-1991 ANSI/ASME B 89.1.5-1998 ANSI/ASME B 89.1.6M-1984 ANSI/ASME B 89.1.9M-1984 ANSI/ASME B 89.3.1-1972 ANSI/ASME B 89.3.4M-1985 ANSI/ASME B 89.4.1-1997 ANSI/ASME B 89.4.1b-2001 ANSI/ASME B 89.7.3.1-2001 测微器 螺纹测量线的测量 Micrometers The Measurement of Threading Measuring Wires 用接触式比较方法校准量块(直径为20英寸和500毫 Calibration of Gage Blocks by Contact 米) Comparison Methods (Through 20 in and 500 mm) 用作校准圆盘塞规或圆柱塞规的普通外径的测量 用作校准环规和环规的合格普通内径的测量 长度测量用精密块规(直径为20英寸和500毫米) 不圆度的测量 旋转轴的规定和试验方法 坐标测量机械的性能评估方法 坐标测量机的性能评价方法 Measurement of Plain External Diameters for Use as Master Discs or Cylindrical Plug Gages Qualified Plain Internal Diameters for Use as Master Rings and Ring Gages, Measurement of Precision Gage Blocks for Length Measurement (through 20 Inches and 500 Millimeters) Out-of-Roundness, Measurement of Axes of Rotation, Methods for Specifying and Testing Methods for Performance Evaluation of Coordinate Measuring Machines Methods for Performance Evaluation of Coordinate Measuring Machines Guidelines for Decision Rules: Considering 决议规则指南:根据规范确定认可性时考虑测量不确定Measurement Uncertainty in Determining 度 Confirmation to Specification

ANSI/ASME B 94.11M-1993 ANSI/ASME B 94.14-1968 ANSI/ASME B 94.14.1-1977 ANSI/ASME B 94.16-1987 ANSI/ASME B 94.16.1-1978 ANSI/ASME B 94.17-1987 ANSI/ASME B 94.17.1-1977 ANSI/ASME B 94.18-1987 ANSI/ASME B 94.18.1-1987 ANSI/ASME B 94.19-1997 ANSI/ASME B 94.2-1995 ANSI/ASME B 94.22-1968 麻花钻 基头型冲床 基头型冲床(米制) Twist Drills Punches - Basic Head Type Punches - Basic Head Type (Metric) Retainers - Basic Ball-Lock Punch and Die 止动装置.轻型和重型基球锁定冲头和冲模的叶状模槽 Button, Light and Heavy Duty 止动装置.轻型和重型基球锁定冲头和冲模的叶状模槽 Retainers, Basic Ball - Lock Punch and Die (米制) Button, Light and Heavy Duty (Metric) 量规.功能球锁定冲头、冲模的叶状模槽和止动装置 Gages - Functional, Ball-Lock Punches, Die Buttons, and Retainers 量规.(功能)球锁定冲头、冲模的叶状模槽和止动装置 Gages (Functional), Ball - Lock Punches, Die (米制) Buttons and Retainers (Metric) 轻型和重型基球锁定冲头 轻型和重型基球锁定冲头(米制) 铣刀和端铣刀 铰刀 可变头型冲床 Punches - Basic Ball-Lock, Light and Heavy Duty Punches, Basic Ball-Lock, Light and Heavy-Duty (Metric) Milling Cutters and End Mills Reamers Punches - Variable, Head Type ANSI/ASME B 94.22.1-1977 ANSI/ASME B 94.23-1969 ANSI/ASME B 94.27-1970 ANSI/ASME B 94.27.1M-1983 ANSI/ASME B 94.28-1970 编号 ANSI/ASME B31.4-2002 ANSI/ASME B31.8-2003 ANSI/ASME B31.8S-2004 ANSI/ASME B31.8S-2004 ANSI/ASME B31.9-2004 ANSI/ASME B36.10M-2004 可变头型冲床(米制) 可变的压配合冲床导衬 压配合基本锥形起伏的冲模的叶状模槽(米制) 压配合基本锥形起伏的冲模的叶状模槽(米制) 压配合基本直线起伏的冲模的叶状模槽 中文名称 烃类、液化石油气、无水氨和醇类用液体输送系统 Punches - Variable, Head Type (Metric) Punch Guide Bushings - Variable, Press Fit Die-Buttons - Basic Taper Relief, Press Fit Die Buttons - Basic Taper Relief, Press Fit (Metric) Die-Buttons - Basic Straight Relief, Press Fit 英文名称 (Liquid Transportation Systems for Hydrocarbons, Liquid Petroleum Gas, Anhydrous Ammonia, and Alcohols ) (Gas Transmission and Distribution Piping Systems ) 气体输送和分配管道系统 燃气管道的管理系统完整性 燃气管道的管理系统完整性 建筑物服务设施用压力管道标准 焊接锻钢管和无缝锻钢管 ANSI/ASME B36.19M-2004 ANSI/ASME B40.200a-2003 ANSI/ASME B46.1-2002 ANSI/ASME B5.52-2003 ANSI/ASME B5.54-2003 ANSI/ASME B5.54-2005 ANSI/ASME B5.60.1-2002 ANSI/ASME B5.60.4-2002 ANSI/ASME B5.60a-2005 ANSI/ASME B5.61-2003 ANSI/ASME B56.1-2004 不锈钢管 直读式和遥控温度计 表面特征(表面粗糙度、波纹度和扭转度) GAP型(米制)通用单点机械动力压力机 计算机数控加工中心机床性能评定方法 (Thermometers, Direct Reading and Remote Reading ) (Surface Texture (Surface Roughness, Waviness, and Lay) ) (Presses, General Purpose, Single Point, Gap Type, Mechanical Power (Metric) ) (Performance Evaluation of Computer Numerically Controlled Machining Centers, Methods for ) 计算机数字控制的组合加工中心机床的性能评定方法 (Workholding Chucks - Jaw Type Chucks, Part 工件夹具.爪式夹具.第1部分:一般说明和术语定义 1: General Description and Definitions of Terms ) 工件夹具.爪式夹具.第4部分:性能试验 工件夹具.爪式夹具(附录) 通用单向压制直边型凹版速印机 低升力和高升力货车 (Workholding Chucks - Jaw Type Chucks, Part 4: Performance Testing ) (Power Presses - General Purpose Single Action Straight Side Type ) ANSI/ASME B56.1b-2003 ANSI/ASME B56.5-2004 ANSI/ASME B56.6-2002 ANSI/ASME B73.2M-2003 ANSI/ASME B73.3M-2003 低起升和高起升车辆 (Low Lift and High Lift Trucks ) 工业导向车辆的安全标准和载人工业车辆的自动化功 能 不平地带用的叉车 化工用立式直列式离心泵规范 不密封卧式端吸装置规范 (Rough Terrain Forklift Trucks ) (Vertical In-Line Centrifugal Pumps for Chemical Process, Specifications for ) (Specification for Sealless Horizontal End Suction ) (Qualified Plain Internal Diameters for Use as Master Rings and Ring Gages, Measurement of ) (Guidelines for Assessing the Reliability of Dimensional Measurement Uncertainty Statements ) Bioprocessing Equipment ASME Boiler and Pressure Vessel Code (ASME Boiler and Pressure Vessel Code (9/14/01 mtg) ) ANSI/ASME 用作校准环规和环规的合格普通内径的测量 B89.1.6M, Rev.2-2002 ANSI/ASME B89.4.22-2004 ANSI/ASME B89.7.3.3-2002 铰接臂坐标测量机械的性能评价方法 尺寸测量不可靠声明的可信赖性评估导则 ANSI/ASME BPE-2002 生物加工设备 ANSI/ASME BPEa-2004 ANSI/ASME BPVC Edition-2001 ANSI/ASME BPVCRevision 生物处理设备 ASME锅炉和压力容器编码 ASME锅炉和压力容器编码(9/14/01 mtg) Addenda-2002 ANSI/ASME BPVCRevision-2004 ANSI/ASME BPVCRevision-2004 ANSI/ASME BPVCRevision-2005 ANSI/ASME CSD-1-2002 ANSI/ASME CSD-1-2004 ANSI/ASME CSD-1-2004 ASME锅炉和压力容器代码.第7节 ASME锅炉和压力容器代码.第7节 ASME锅炉和压力容器代码 自动点火锅炉用控制和安全设备 自动点火锅炉用控制和安全设备 自动点火锅炉用控制和安全设备 Controls and Safety Devices for Automatically Fired Boilers High Pressure Systems (High Pressure Systems ) Performance Standard for Electric Chain Hoists Performance Standard for Hand Chain Manually Operated Chain Hoists Performance Standard for Manually Lever-Operated Chain Hoists Performance Standard for Overhead Electric Wire Rope Hoists ANSI/ASME HPS-1994 高压系统 ANSI/ASME HPS-2003 高压系统 ANSI/ASME HST-1M-1989 ANSI/ASME HST-2M-1989 ANSI/ASME HST-3M-1991 ANSI/ASME HST-4M-1991 电动环链起重机性能标准 手链式人工操作环链起重机性能标准 手柄式人工操作环链起重机性能标准 悬吊式电动缆索起重机性能标准

ANSI/ASME HST-5M-1991 ANSI/ASME HST-6M-1986 ANSI/ASME MC 88.1-1972 ANSI/ASME MC 88.2-1974 ANSI/ASME MFC-10M-1994 ANSI/ASME MFC-11M-1989 ANSI/ASME MFC-11M-2003 ANSI/ASME MFC-14M-1995 ANSI/ASME MFC-14M-2003 ANSI/ASME MFC-16M-1995 ANSI/ASME MFC-18M-2001 ANSI/ASME 气动环链起重机性能标准 气动钢索起重机性能标准 压力传感器的动态校准导则 Air Chain Hoists Performance Standard for Air Wire Rope Hoists Dynamic Calibration of Pressure Transducers, Guide for Bench Calibration of Tank Level Gaging Tapes and Sounding Rules, Procedure for (formerly designated as ANSI B88.2) Method for Establishing Installation Effects on Flowmeters Measurement of Fluid Flow By Means of Coriolis Mass Flowmeters (Measurement of Fluid Flow by Means of Coriolis Flowmeters ) Measurement of Fluid Flow Using Small Bore Precision Orifice Meters (Measurement of Fluid Flow Using Small Bore Precision Orifice Meters ) Measurement of Fluid Flow in Closed Conduits by Means of Electromagnetic Flowmeters Measurement of Fluid Flow in Pipes Using Variable Area Meters Measurement of Fluid Flow, Glossary of Terms 容器水位测定皮尺和探深尺台架校准程序 确定安装对流量计的影响方法 利用科氏质量流量计测量液体流量 用科氏流量计测量液体流量 小孔精确孔板仪测量液体流量 小孔精确孔板仪测量液体流量 用电磁流量仪测量封闭管道中液体流量 用可变面积计量计测量管道中的液体流量 液体流量测量用术语汇编 MFC-1M-1991 ANSI/ASME MFC-1M-2003 ANSI/ASME MFC-3M-1-2004 ANSI/ASME MFC-3M-2-2004 ANSI/ASME MFC-3M-3-2004 ANSI/ASME MFC-3M-4-2004 ANSI/ASME MFC-4M-1986 ANSI/ASME MFC-5M-1985 ANSI/ASME MFC-6M-1998 ANSI/ASME MFC-7M-1987 ANSI/ASME MFC-8M-1988 ANSI/ASME MH 液体流量测量用术语汇编 Used in the (Measurement of Fluid Flow, Glossary of Terms Used in the ) 用孔板、喷嘴和文杜利流量计测量管道中液体流量.第 1部分:总则 用孔板、喷嘴和文杜利流量计测量管道中液体流量.第 2部分:孔板 用孔板、喷嘴和文杜利流量计测量管道中液体流量.第 3部分:喷嘴和文杜利喷嘴 用孔板、喷嘴和文杜利流量计测量管道中液体流量.第 4部分:文杜利流量计 涡轮仪测量气体流量 Measurement of Gas Flow by Turbine Meters Liquid Flow in Closed Conduits Using 利用过渡时间超声流量计测量密封管道中的液体流量 Transit-Time Ultrasonic Flow Meters, Measurement of 用涡流流量计测量管道中的液体流量 利用临界流量文氏喷嘴管测量气体流量 Fluid Flow in Pipes Using Vortex Flow Meters, Measurement of Gas Flow by Means of Critical Flow Venturi Nozzles, Measurement of Fluid Flow in Closed Conduits - Connections 密封管道中液体流量.主设备和副设备之间压力信号传for Pressure Signal Transmission Between 导的连接 Primary and Secondary Devices 涉及托盘及相关结构的定义和术语 Definitions and Terminology Covering Pallets 1.1.2-1996 ANSI/ASME MH 1.2.2M-1989 托盘尺寸 and Related Structures Pallet Sizes Procedures for Testing Pallets Slip Sheets Standard Procedures for Determination of Durability of Wooden Pallets and Related Structures Driven Fasteners for Assembly of Pallets and Related Structures Wood Pallets Export Pallets Pallets, Slip Sheets, and Other Bases for Unit Loads (Pallets, Slip Sheets, and Other Bases for Unit Loads ) Self-Operated and Power Operated Safety-Related Valves Functional Specification Standard ANSI/ASME MH 托盘试验程序 1.4.1M-1996 mh 1-1997 ANSI/ASME MH 1.5M-1993 薄衬纸 ANSI/ASME MH 木制托盘和相关结构耐久性测定用标准程序 1.6-1996 mh 1-1997 ANSI/ASME MH 托盘及相关结构的组配用传动紧固件 1.7M-1996 mh 1-1997 ANSI/ASME MH 1.8M-1996 ANSI/ASME MH 1a Part IV-1998 ANSI/ASME MH 1b-2000 木制托盘 出口商品用托盘 成组货件用托盘、滑板和其他底座 ANSI/ASME MH1-2003 成组货件用托盘、滑板和其它基板 ANSI/ASME MH1-2005 成组货件用托盘、滑板和其它基板 ANSI/ASME N 278.1-1975 与安全相关的自动和机动阀门功能规范标准 ANSI/ASME N 509-1989 ANSI/ASME N 510-1989 ANSI/ASME N 626.3-1993 ANSI/ASME N509-2002 ANSI/ASME NOG-1-2002 ANSI/ASME NOG-1-2004 ANSI/ASME NQA-1-2004 ANSI/ASME NQA-1a-2002 ANSI/ASME NUM-1-1996 ANSI/ASME NUM-1-2004 ANSI/ASME NUM-1a-2002 核电厂空气净化设备和部件 核空气净化系统的测试 特殊专业工程师的资格鉴定和责任 核电厂空气净化设备和部件 桥式和门式起重机(支承桥和多横梁)的制造规则 桥式和门式起重机(支承桥和多横梁)的制造规则 核设施的质量保证要求 核设施的质量保证要求 Nuclear Power Plant Air Cleaning Units and Components Testing of Nuclear Air-Cleaning Systems Qualifications and Duties of Specialized Professional Engineers (Nuclear Power Plant Air Cleaning Units and Components ) Overhead and Gantry Cranes (Top Running Bridge, Multiple Girder), Rules for Construction of (Quality Assurance Requirements for Nuclear Facility Applications ) Rules for Construction of Cranes, Monorails, 起重机、单轨铁路和提升机的制造规则(带有悬桥或悬and Hoists (with Bridge or Trolley or Hoist of 挂式吊车或悬挂式提升机) the Underhung Type) 起重机、单轨吊车和提升机的制造规则(带有悬桥或悬 挂式吊车或悬挂式提升机) 起重机、单轨和提升机的建造规则 (Rules for Construction of Cranes, Monorails and Hoists ) ANSI/ASME NUM-1b-2002 ANSI/ASME OM Code-2001 起重机、单轨铁路和提升机的制造规则 核动力工厂的维护和操作 (Rules for Construction of Cranes, Monorails, and Hoists ) Operation and Maintenance of Nuclear Power Plants Operation and Maintenance of Nuclear Power Plants Standards and Guides for Operation and Maintenance of Nuclear Power Plants (Standards and Guides for Operation and Maintenance of Nuclear Power Plants ) (Operation and Maintenance of Nuclear Power Plants ) Portable Automotive Lifting Devices (Portable Automotive Lifting Devices ) ANSI/ASME OM-1990 核电站的运行和养护 ANSI/ASME OM-S/Ga-2001 ANSI/ASME OM-S/Ga-2004 ANSI/ASME OMaCode-2005 ANSI/ASME OMb-S/G-2003 ANSI/ASME OMb-S/G-2005 ANSI/ASME OMbCode-2003 ANSI/ASME OMCode-2004 ANSI/ASME PALD-1997 ANSI/ASME PALD-2003 核动力工厂的维护和操作的标准和指南 核电站的运行和维护的标准和指南 核电厂的操作和维修规范 核电站的操作和维修标准和指南 核电厂操作和维护的标准和指南 核电站的操作和维修 核电厂的维护和操作标准 便携式自动提升装置 便携式自动提升装置

ANSI/ASME PALDb-2002 ANSI/ASME PCC-1-2000 ANSI/ASME PTC 10-1974 ANSI/ASME PTC 10.1-1997 ANSI/ASME PTC 11-1984 ANSI/ASME PTC 12.1-1978 ANSI/ASME PTC 12.2-1998 ANSI/ASME PTC 12.3-1997 ANSI/ASME PTC 12.4-1992 ANSI/ASME PTC 12.5-2000 ANSI/ASME PTC 14-1970 ANSI/ASME PTC 16-1958 可移动自动升降装置 压力界限法兰连接接头组件的导则 性能测试规范.压缩机及排气机 压缩机和排气器的临时试验标准 风扇 性能测试规范.密封式供水加热器 蒸汽冷凝装置的性能试验标准 空气分离器 脱湿器再热炉 单相热交换器 性能测试规范.蒸发装置 性能测试规范.气体发生器和连续气体发生器 Portable Automotive Lifting Devices Guidelines for Pressure Boundary Bolted Flange Joint Assembly Performance Test Code - Compressors and Exhausters Interim Test Code on Compressors and Exhausters Fans Performance Test Code - Closed Feedwater Heaters Performance Test Code - Steam-Condensing Apparatus Deaerators Moisture Separator Reheaters Single Phase Heat Exchangers Performance Test Code - Evaporating Apparatus Performance Test Code - Gas Producers and Continuous Gas Generators ANSI/ASME PTC 17-1973 ANSI/ASME PTC 18-1992 ANSI/ASME PTC 19.1-1998 ANSI/ASME PTC 19.11-1997 ANSI/ASME PTC 19.2-1987 ANSI/ASME PTC 19.22-1986 ANSI/ASME PTC 19.23-1980 ANSI/ASME PTC 19.3-1974 ANSI/ASME PTC 19.7-1980 ANSI/ASME PTC 19.8-1970 编号 ANSI/ASME PTC 2-1980 ANSI/ASME PTC 性能试验规范.往复式内燃机 水轮机 测量不确定度.仪器和装置 动力循环中水和蒸汽的取样、调节和分析 压力测量仪器仪表.第2部分 仪器仪表.数字系统技术 模型试验指导手册.仪器仪表 性能测试规范.温度测量 轴功率测量.仪器仪表 性能测试规范.测量指示功率用仪器仪表 中文名称 性能测试规范.定义和数值 汽轮发电机组的速度和负载调节系统 Performance Test Code - Reciprocating Internal-Combustion Engines Hydraulic Turbines Measurement Uncertainty - Instruments and Apparatus Steam and Water Sampling, Conditioning and Analysis in the Power Cycle Pressure Measurement Instruments and Apparatus - Part 2 Instruments and Apparatus - Digital Systems Techniques Guidance Manual for Model Testing - Instruments and Apparatus Performance Test Code - Temperature Measurement Measurement of Shaft Horsepower - Instruments and Apparatus Performance Test Code - Measurement of Indicated Power, Instruments and Apparatus 英文名称 Performance Test Codes - Definitions and Values Speed and Load Governing Systems for Steam 20.1-1977 ANSI/ASME PTC 20.2-1965 ANSI/ASME PTC 20.3-1970 ANSI/ASME PTC 21-1991 ANSI/ASME PTC 22-1997 ANSI/ASME PTC 23-1986 ANSI/ASME PTC 25-1994 ANSI/ASME PTC 28-1965 ANSI/ASME PTC 29-1980 ANSI/ASME PTC 3.1-1974 ANSI/ASME PTC 3.2-1990 ANSI/ASME PTC 3.3-1974 ANSI/ASME PTC 汽轮发电机组的超速切断系统 性能测试规范.汽轮发电机组用压力控制系统 散粒物质集聚设备 燃气轮机的性能试验规则 大气水冷却设备 减压设备 性能测试规范.细微散粒物质的特性测定 水力涡轮发电机组的速度调节系统 性能测试规范.柴油机和燃烧器的燃料 性能测试规范.煤和焦炭 性能测试规范.气体燃料 空气冷却换热器 Turbine Generator Units Overspeed Trip Systems for Steam Turbine - Generator Units Performance Test Code - Pressure-Control Systems Used on Steam Turbine-Generator Units Particulate Matter Collection Equipment Performance Test Code on Gas Turbines Atmospheric Water Cooling Equipment Pressure Relief Devices Performance Test Code - Determining the Properties of Fine Particulate Matter Speed-Governing Systems for Hydraulic Turbine-Generator Units Performance Test Code - Diesel and Burner Fuels Performance Test Code - Coal and Coke Performance Test Code - Gaseous Fuels Air Cooled Heat Exchangers 30-1991 ANSI/ASME PTC 31-1973 ANSI/ASME PTC 32.1-1969 ANSI/ASME PTC 32.2-1978 ANSI/ASME PTC 33-1978 ANSI/ASME PTC 33a-1980 ANSI/ASME PTC 36-1985 ANSI/ASME PTC 38-1980 ANSI/ASME PTC 39.1-1980 ANSI/ASME PTC 4.1-1964 ANSI/ASME PTC 4.2-1969 ANSI/ASME PTC 4.3-1974 ANSI/ASME PTC 性能测试规范.离子交换器 性能测试规范.核装置蒸汽供给系统 轻水反应堆中核燃料性能测试方法 大型焚化炉的性能测试规范 大型焚化炉的性能测试规范 工业声音的测量 性能测试规范.气流中散粒物质浓度的测定 性能测试规范.蒸汽系统中消除凝结物装置 Performance Test Code - Ion Exchange Equipment Performance Test Code - Nuclear Steam Supply Systems Nuclear Reactor Fuel in Light Water Reactors, Methods of Measuring the Performance of Large Incinerators, Performance Test Code for Large Incinerators, Performance Test Code for Industrial Sound, Measurement of Concentration of Particulate Matter in a Gas Stream, Determining - Performance Test Code Condensate Removal Devices for Steam Systems - Performance Test Code 性能测试规范.蒸气发生器(包括ASME1968及1969的补 Performance Test Code - Steam Generating 充件) Units (includes ASME 1968 and 1969 addenda) 性能试验规范.煤炭粉碎机 性能测试规范.空气加热器 燃气轮机热回收蒸汽发电机 Performance Test Code - Coal Pulverizers Performance Test Code - Air Heaters Gas Turbine Heat Recovery Steam Generators 4.4-1981 ANSI/ASME PTC 40-1991 ANSI/ASME PTC 42-1988 ANSI/ASME PTC 46-1996 ANSI/ASME PTC 6 App-1982 ANSI/ASME PTC 6-1996 ANSI/ASME PTC 6R-1985 ANSI/ASME PTC 6S-1988 ANSI/ASME PTC 9-1974 ANSI/ASME PTC1-2004 ANSI/ASME PTC18-2002 ANSI/ASME PTC19.2-2004 烟道脱硫装置 风力涡轮机 总体工厂性能 汽轮机的性能试验标准(ANSI/ASME PTC 6的补充) 汽轮机的性能试验标准6 性能试验规范.汽轮机中不确定性测量的评定指南 Flue Gas Desulfurization Units Wind Turbines Overall Plant Performance Performance Test Code - Steam Turbines (appendix to ANSI/ASME PTC 6) Performance Test Code 6 on Steam Turbines Performance Test Code - Steam Turbines, Guidance for Evaluation of Measurement Uncertainty Performance Test Code - Steam Turbines, Simplified Procedures for Routine Tests Performance Test Code - Displacement Compressors, Vacuum Pumps and Blowers (Hydraulic Turbines and Pump - Turbines ) 性能测试规范.蒸汽涡轮机例行试验简化程序 性能试验规范.容积式压缩机、真空泵和鼓风机 性能试验规则.通用说明书 水轮机和泵.涡轮机 压力测量仪器仪表.第2部分

ANSI/ASME PTC19.5-2002 ANSI/ASME PTC19.5-2004 ANSI/ASME PTC22-2005 ANSI/ASME PTC23-2003 ANSI/ASME PTC29-2005 ANSI/ASME PTC39.1-2005 ANSI/ASME PTC50-2002 ANSI/ASME PTC6.2-2004 ANSI/ASME PVHO-1-2002 ANSI/ASME PVHO-2-2003 ANSI/ASME QEI-1-1993 ANSI/ASME 流量测量 流量测量 燃气轮机的性能试验规程 大气水冷却设备 水力涡轮发电机组的速度调节系统 凝水排除器 燃料电池动力系统性能 联合循环蒸汽涡轮机 人占用的压力容器的安全标准 人用压力容器的安全标准.PVHO丙烯酸窗口在使用中的指南= 电梯检验员的资格鉴定 电梯检验员的资格鉴定 (Flow Measurement ) (Atmospheric Water Cooling Equipment ) (Fuel Cell Power Systems Performance ) Safety Standard for Pressure Vessels for Human Occupancy (Safety Standard for Pressure Vessel for Human Occupancy In-Service Guidelines for PVHO Acrylic Windows ) Qualification of Elevator Inspectors QEI-1-2004 ANSI/ASME QEI-1b-2003 ANSI/ASME QFO-1-1998 ANSI/ASME QHO-1-1994 ANSI/ASME QHO-1-2004 ANSI/ASME QHO-1-2004 ANSI/ASME QME-1-1994 ANSI/ASME QME-1-2002 ANSI/ASME QRO-1-1994 ANSI/ASME QRO-1-2005 ANSI/ASME RA-S-2002 ANSI/ASME RA-Sa-2003 电梯检验员的资格鉴定 高效能矿物燃料燃烧设备操作人员的资格鉴定 危险废物焚烧炉操作人员的资格鉴定和认证 危险废物焚烧炉操作人员的资格鉴定和认证 危险废物焚烧炉操作人员的资格鉴定和认证 (Qualification of Elevator Inspectors ) Qualification of High Capacity Fossil Fuel Fired Plant Operators Qualification and Certification of Hazardous Waste Incinerator Operators (Qualification and Certification of Hazardous Waste Incinerator Operators ) Section QV Functional Qualification 第QV节:核电站现用阀门组件的功能合格的鉴定要求Requirements for Active Valve Assemblies for (ANSI/B16.41-83(R89)的修订和更换代号) Nuclear Power Plants 核电站现用机械设备的质量要求 资源回收设施操作人员的资格鉴定和认证 资源回收设施操作人员的资格鉴定和认证 核动力厂设施的概率风险评估 核动力厂设施的概率风险评估 (Qualification of Active Mechanical Equipment for Nuclear Power Plants ) Qualification and Certification of Resource Recovery Facility Operators Probabilistic Risk Assessment for Nuclear Power Plant Applications (Probabilistic Risk Assessment for Nuclear Power Plant Applications ) ANSI/ASME RTP-1-1989 ANSI/ASME RTP-1b-2002 ANSI/ASME RTP-1c-2003 ANSI/ASME RTP-1d-2004 ANSI/ASME RTP-1d-2004 ANSI/ASME TDP-1-1998 ANSI/ASME Y 1.1-1989 ANSI/ASME Y 14.1-1995 ANSI/ASME Y 14.100M-1998 ANSI/ASME Y 14.13M-1981 ANSI/ASME Y 14.18M-1986 增强热固塑料防腐设备 增强热固性塑料防腐设备 增强热固性塑料耐腐蚀设备 增强热固性塑料防腐设备 增强型热固性塑料防腐设备 发电用蒸汽轮机防水损的推荐实施规程 Reinforced Thermoset Plastic Corrosion Resistant Equipment (Reinforced Thermoset Plastic Corrosion Equipment ) (Reinforced Thermoset Plastic Corrosion Resistant Equipment ) Recommended Practices for the Prevention of Water Damage to Steam Turbines Used for Electric Power Generation Abbreviations for Use on Drawings and in Text Decimal Inch Drawing Sheet Size and Format Engineering Drawing Practices Engineering Drawing and Related Documentation Practices - Mechanical Spring Representation Engineering Drawings and Related Documentation Practices - Optical Parts 在制图和文本中使用的缩略语 十进制的英寸绘制图尺寸和格式 工程制图实施规程 工程图纸及相关文献.机械弹簧表示法 工程图纸及相关文献.光学部件 ANSI/ASME Y 14.1M-1995 ANSI/ASME Y 14.24M-1989 ANSI/ASME Y 14.2M-1992 ANSI/ASME Y 14.32.1M-1994 ANSI/ASME Y 14.34M-1996 ANSI/ASME Y 14.35M-1997 ANSI/ASME Y 14.36M-1996 ANSI/ASME Y 14.3M-1994 ANSI/ASME Y 14.4M-1989 ANSI/ASME Y 14.5.1M-1994 ANSI/ASME Y 14.5M-1994 ANSI/ASME Y 14.6-1978 米制绘制图尺寸和格式 工程图纸的类型及其应用 图线画法和字体 底盘车架.轿车和轻型卡车.陆上车辆操作规程 相关表 工程图纸及其相关文献的修订 表面纹理符号 投影图和截面图 直观图 尺寸计算和公差.原理的数学定义 尺寸和公差计算 工程图纸及相关文献.螺纹表示法 Metric Drawing Sheet Size and Format Types and Applications of Engineering Drawings Line Conventions and Lettering Chassis Frames - Passenger Car and Light Truck - Ground Vehicle Practices Associated Lists Revision of Engineering Drawings and Associated Documents Surface Texture Symbols Multiview and Sectional View Drawings Pictorial Drawing Dimensioning and Tolerances - Mathematical Definitions of Principles Dimensioning and Tolerancing Screw Thread Representation, Engineering Drawing and Related Documentation Practice ANSI/ASME Y 14.6aM-1981 ANSI/ASME Y 14.7.1-1971 ANSI/ASME Y 14.8M-1996 ANSI/ASME Y 32.2.3-1949 ANSI/ASME Y14.1-2005 ANSI/ASME Y14.100-2004 ANSI/ASME Y14.100-2004 ANSI/ASME Y14.100-2004 ANSI/ASME Y14.1M-2005 ANSI/ASME Y14.38a-2002 ANSI/ASME Y14.40.0-2002 工程图纸及相关文献.螺纹表示法(米制补充件) Engineering Drawing and Related Documentation Practices - Screw Thread Representation (Metric Supplement) 齿轮绘图标准.第1部分:正齿轮、斜齿轮、人字齿轮和 Gear Drawing Standards - Part 1, for Spur, 齿条 Helical, Double Helical, and Rack 铸件和锻件 管配件、阀门和管道用图形符号 十进制英制绘图纸规格和格式 工程图制图规程 工程图制图规程 工程图制图规程 米制绘图纸规格和格式 缩写和缩写字母 Castings and Forgings Graphical Symbols for Pipe Fittings, Valves and Piping (Abbreviations and Acronyms ) (Basic Rules for the Design of Graphical Symbols for Use in the Technical Documentation of Products ) 产品技术文献中使用的图形符号的设计基本规则

本文来源：https://www.bwwdw.com/article/cmdw.html