SmartPlant Spoolgen Labs

SmartPlant Spoolgen

Training Labs

Version 2.0

Date 10/06/10

Doc Number

DSPG-TP-100002A

Copyright

Copyright ? 2009 Intergraph Corporation. All Rights Reserved.

Including software, file formats, and audiovisual displays; may be used pursuant to applicable software license agreement; contains confidential and proprietary information of Intergraph and/or third parties which is protected by copyright law, trade secret law, and international treaty, and may not be provided or otherwise made available without proper authorization from Intergraph Corporation.

U.S. Government Restricted Rights Legend

Use, duplication, or disclosure by the government is subject to restrictions as set forth below. For civilian agencies: This was developed at private expense and is \the Commercial Computer Software - Restricted Rights clause at 52.227-19 of the Federal Acquisition Regulations (\and is unpublished and all rights are reserved under the copyright laws of the United States. For units of the Department of Defense (\This is \227.7202-3.

Unpublished - rights reserved under the copyright laws of the United States. Intergraph Corporation

Huntsville, Alabama 35894-0001

Terms of Use

Use of this software product is subject to the End User License Agreement and Limited Product Warranty (\software product unless the licensee has a valid signed license for this software product with Intergraph Corporation. If the licensee has a valid signed license for this software product with Intergraph Corporation, the valid signed license shall take precedence and govern the use of this software product. Subject to the terms contained within the applicable license agreement, Intergraph Corporation gives licensee permission to print a reasonable number of copies of the documentation as defined in the applicable license agreement and delivered with the software product for licensee's internal, non-commercial use. The documentation may not be printed for resale or redistribution. Intergraph and the Intergraph logo are registered trademarks of Intergraph Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation. Other brands and product names are trademarks of their respective owners.

Warranties and Liabilities

All warranties given by Intergraph Corporation about equipment or software are set forth in the EULA provided with the software or applicable license for the software product signed by Intergraph Corporation, and nothing stated in, or implied by, this document or its contents shall be considered or deemed a modification or amendment of such warranties. Intergraph believes the information in this publication is accurate as of its publication date.

The information and the software discussed in this document are subject to change without notice and are subject to applicable technical product descriptions. Intergraph Corporation is not responsible for any error that may appear in this document.

The software discussed in this document is furnished under a license and may be used or copied only in accordance with the terms of this license. No responsibility is assumed by Intergraph for the use or reliability of software on equipment that is not supplied by Intergraph or its affiliated companies. THE USER OF THE SOFTWARE IS EXPECTED TO MAKE THE FINAL EVALUATION AS TO THE USEFULNESS OF THE SOFTWARE IN HIS OWN ENVIRONMENT.

Intergraph is not responsible for the accuracy of delivered data including, but not limited to, catalog, reference and symbol data. Users should verify for themselves that the data is accurate and suitable for their project work.

Trademarks

Intergraph, the Intergraph logo, PDS, SmartPlant, SmartSketch, FrameWorks, INtools, MARIAN, and IntelliShip are registered trademarks and SupportModeler and SupportManager are trademarks of Intergraph Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation. MicroStation is a registered trademark of Bentley Systems, Inc. ISOGEN and SPOOLGEN are registered trademarks of Alias Limited.

Contents

Introduction ................................................................................................................................................. 2 Lab 1 - Aims & Objectives ............................................................................................................................ 3 Lab 1 – Basic Functions ................................................................................................................................ 1 Lab 2 - Aims & Objectives .......................................................................................................................... 14 Lab 2 – Further Functions .......................................................................................................................... 15 Lab 3 – Aims & Objectives ......................................................................................................................... 27 Lab 3 – Material Editor ............................................................................................................................... 28 Lab 4 – Aims & Objectives ......................................................................................................................... 40 Lab 4 – Advanced and techniques ............................................................................................................. 41

Replay .................................................................................................................................................. 41

Converting elbows to bends ................................................................................................................. 43 Weld Gaps ............................................................................................................................................ 47 Revision History ......................................................................................................................................... 51

错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。 1

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

Introduction

SmartPlant Spoolgen is a high productivity isometric drawing system that creates spool sheets and isometric drawings from piping data files. Because it is a self-contained system, it requires no other software to drive it with the exception of a 2D graphics system for the viewing and plotting of the output isometrics. The following graphic illustrates the standard flow of data:

2错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

Lab 1 - Aims & Objectives

This lab is intended to show you the basics of SmartPlant Spoolgen, after this lab you will understand the basic workflow and basic functions. The following features will be shown:

? Importing data (IDF) ? Checking in / Checking out ? Splitting drawings

? Adding site and workshop welds ? Adding Pipeline Attributes ? Generating isometrics

? Understanding the Workflow Database

错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。 3

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

9. Place the split point at the location shown below and select the Tick icon to confirm placement:

10. Next we are going to update the view (refresh) this will recalculate the POD file and split the

isometric into two sheets. Select the Update Current View icon.

The isometric will now be split onto two sheets; the title bar shows the sheet that is currently active.

You can control the sheets by using the Window menu, or by double clicking on the Sheet property in the tree View

错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。 5

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

11. The next step is to place some welds, you are going to place Site Welds which will break the isometric

into smaller spools. Select the Place Site Weld icon.

Place the welds at the following locations:

Sheet 1

6错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

Sheet 2

错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。 7

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

12. Next, you are going to place a weld in the section of pipe on sheet 1, place a Work Shop Weld as

shown below:

13. The next step is to add some information to the pipeline attributes, right click in the white space and

select Pipeline Properties:

8错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

14. Enter values as shown:

The values entered above can be outputted to the generated Isometrics and reports.

错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。 9

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

15. You are now going to generate the outputs; the first output will be the Spools, right click in

whitespace and select Generate Spools, or select the Generate Spools icon

This should generate 8 spool drawings.

16. View the drawings and check for accuracy.

17. Generate a different style of Isometric, this time select Generate Drawing and then select the

Final-Weld-Box style, select OK to generate.

10错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

18. This should generate 2 drawings, view the drawings and check for accuracy.

19. Save and close SG-T1

20. As a final step Check In SG-T1, this effectively completes the processing of this pipeline.

错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。 11

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

21. View the Work Flow database, not SG-T1 is now marked as complete

12错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

End of lab

错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。 13

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

Lab 2 - Aims & Objectives

This lab is intended to show you further functionality of SmartPlant Spoolgen, after this lab you will understand the basic workflow and some further functions. The following features will be shown:

? Importing

? Checking in / Checking out ? Using the AutoSplit function

? Changing categories of multiple components ? Adding Supports ? Adding Support Welds ? Adding Messages

? Adding Reference Dimensions ? Adding FFW welds ? Generating isometrics

14错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

13. Next place 2 flow arrows as shown, ensure the direction is correct.

14. Place 3 supports on each elbow at elevation -6313, place the supports at the elbow

intersection (no offset). Define the support like this:

20错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

15. Next you are going to add some support welds, right click on the support and select Add >

Support Weld

16. Define the support weld like shown:

17. Repeat for all 3 supports

错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。 21

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

18. Next you are going to place messages, select the Place Info icon

19. Define the message like shown:

20. Place the message on all three vertical valves

Note the $ symbol, this will make a line return on the generated drawing like shown below:

21. Now you will add a reference dimension, select the Reference Dimension icon

22. Place the Reference Dimension on the flange face

22错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

23. Define the reference dimension as shown:

错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。 23

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

Spoolgen View Generated View

24. Next you are going to generate the Spools and Isometrics, select Generate Spools.

25. View the outputs and check for accuracy.

26. Generate the isometrics using the Final-Weld-Box style

24错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

27. View the outputs and check for accuracy.

28. Finally you are going to save, close and check in the SG-T2, select File > Close

29. Check in the file

30. As a final check, view the Workflow Database

错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。 25

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

Note the User Status, the file should be marked as Complete.

End of lab

26错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

Lab 3 – Aims & Objectives

This lab covers the use of the Spoolgen Material Editor: ? Creating a new Project Material Database ? Adding new Supports ? Adding Bolts

? Adding Additional Material

? Specifying the database in I-Configure ? Placing the new material in Spoolgen

错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。 27

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

Lab 3 – Material Editor

1. Start the Material Editor

2. Create a new database

3. Define the database as shown below:

4. The database will be empty, select Insert > New Material to start adding data using the

Material Builder

28错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

5. Expand the tree list for Supports and select Support

6. Define the item code, description and skey as shown

7. Add the following sizes – 4”

8. Select Add to update the database

9. Add a further pipe support, define it like shown

错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。 29

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

10. Select Add to update the database

11. Next you are going to add a bolt, select the Bolt component type in the tree list and

define the bolts like shown

12. Select Add to update the database

13. Save the changes

14. You will be prompted to supply a name and location from the saved database, browse

to “C:\\SampleIsoDir\\S5Tutorial\\Data\\Materials” and call the database “Training.mdb”.

30错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

You are now going to add some welds, this can be done quickly by using the Auto Create function, select Material > Auto Create > Welds

15. Select all the weld types and define a root gap of 0mm, we don’t actually need all the

welds but this will show how quickly all welds can be created.

错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。 31

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

16. Select Generate to create the welds.

17. Close the Material Builder and close the Material Editor program.

The new database must be referenced in the project; this is done using the I-Configure program

18. Start I-Configure

19. Select the S5Tutorial project and select the Project Defaults icon

32错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

20. Change the Material Database so it references the new database

错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。 33

错误！使用“开始”选项卡将 Heading 1 应用于要在此处显示的文字。

21. Select OK to update the Project Defaults 22. Close I-Configure

You are now going to use the database in Spoolgen

23. Start Spoolgen

24. Import and check out SG-T3.idf

25. Right click on the existing support and select “Change Material”

34错误！使用“开始”选项卡将 Title 应用于要在此处显示的文字。 错误！使用“开始”选项卡将 Subtitle 应用于要在此处显示的文字。

本文来源：https://www.bwwdw.com/article/ba87.html