瑞士万通离子色谱仪800 Dosino进样器说明书--中文

800 Dosino – 开始参数

标签: 方法 ? 设备 ? Dosino 溶液

Select the solution for the Dosino that should be available when the hardware is started with [Start HW]. A check is carried out in the method run to ensure that the correct solution has been put on the dosing device. When the method is started, the working life and GLP test interval are checked for the selected solution.

选择 未定义 | Solutions from the solution table 默认值 未定义 未定义

The solution is not checked.

Solutions from the solution table

Only \solutions, i.e. solutions that are assigned to an 807 Dosing unit, can be selected. Connector

Shows the main device and the MSB connector which the 800 Dosino is on.

800 Dosino – 命令

Overview of the time program commands available for the 800 Dosino:

加液

对话窗口：方法 ? 时间程序 ? 编辑 ? ‘设备’ – 加液

The device-dependent time program command Dosing (command with feedback) doses the specified volume via the defined port. There is no automatic filling beforehand or afterwards.

参数

Port

Port via which dosing takes place. Formula input possible.

1 ... 4 1

范围 默认值 Volume

Volume to be transported. Formula input possible.

范围 默认值 Dosing rate

0.0000 ... 99999.9000 mL 1.0000 mL

Speed at which discharge takes place. The 最大值 rate depends on the cylinder volume of the buret used. Formula input possible.

Cylinder volume 2 mL

范围 默认值 选择 Filling rate

0.01 ... 6.00 mL/min 1.00 mL/min 最大值

Speed at which filling takes place. The 最大值 rate depends on the cylinder volume of the buret used. Formula input possible.

Cylinder volume 2 mL

范围 默认值

0.01 ... 6.00 mL/min 1.00 mL/min

选择 最大值

命令

时间程序命令的可选注释。

Input

64 characters

生成的变量

The following type 'TP.command number.Variable name' variables are generated by the command: Variable name Description CONC DVOL Data type Concentration of the dosed solution as long as one Number has been assigned to the Dosino. Dosed volume [mL] Number 吸液

对话窗口：方法 ? 时间轴 ? 编辑 ? ‘设备’ – 吸液

The device-dependent time program command Aspirate (command with feedback)

draws in the specified volume via the defined port. As with the command Dosing, the cylinder is not filled automatically beforehand or afterwards. It should be possible to achieve the volume to be aspirated with a single piston stroke.

参数

Port

Port via which aspiration takes place. Formula input possible.

1 ... 4 1

范围 默认值 Volume

Volume to be transported. Formula input possible.

范围 默认值 Rate

0.0000 ... 50.0000 mL 1.0000 mL

The 最大值 rate depends on the cylinder volume of the buret used. Formula input possible.

Cylinder volume 2 mL

范围 选择 默认值

0.01 ... 6.00 mL/min 最大值 最大值

命令

时间程序命令的可选注释。

Input

64 characters

生成的变量

The following type 'TP.command number.Variable name' variables are generated by the command: Variable name Description AVOL Aspirated volume [mL] Data type Number 充液

对话窗口：方法 ? 时间轴 ? 编辑 ? ‘设备’ – 充液

The device-dependent time program command Fill (command with feedback) fills the cylinder via the specified port. The valve disc stops on the selected port.

参数

Port

Port via which filling takes place. Formula input possible.

范围 默认值 Rate

1 ... 4 2

The 最大值 rate depends on the cylinder volume of the buret used. Formula input possible.

Cylinder volume 2 mL

范围 选择 默认值

0.01 ... 6.00 mL/min 最大值 最大值

命令

时间程序命令的可选注释。

Input

64 characters

排空

对话窗口：方法 ? 时间轴 ? 编辑 ? ‘设备’ – 排空

The device-dependent time program command Eject to end volume (command with feedback) ejects the entire contents of the cylinder via the specified port. In contrast to the command Eject to stop, the piston travels to the 最大值 volume mark i.e. until it has performed 10,000 pulses. This command should be used for pipetting functions for emptying the cylinder.

参数

Port

Port via which ejection takes place. Formula input possible.

范围 默认值 Rate

1 ... 4 4

选择 默认值

Dosing | Aspirate | Fill | Prepare | Empty Dosing

Dosing

Doses the specified volume via the defined port. There is no automatic filling beforehand or afterwards. Aspirate

Aspirates the specified volume via the defined port. There is no automatic filling beforehand or afterwards. Fill

The cylinder is filled in a fixed sequence. The parameters required for this process are stored in the configuration of the solution. Prepare

The cylinder and all the tubing of a dosing unit are rinsed in an extensive cleaning sequence. The parameters required for this process are stored in the configuration of the solution. Empty

The cylinder and all the tubing of a dosing unit are emptied in an extensive sequence. The parameters required for this process are stored in the configuration of the solution. Solution

Displays the solution assigned to the Dosino.

Volume

Current value

Displays the current dosed volume.

Input

Enter the volume that is to be dosed / moved.

范围 默认值

0.0000 ... 99999.9000 (Exception: with command \ 1.0000 mL

Port

Current value

Shows the current port.

Input

选择 of a port for the action selected in the parameter Command.

范围 默认值

1 ... 4 1

Dosing rate

Input

Enter dosing rate. The 最大值 rate depends on the cylinder volume of the buret used. Formula input possible.

Cylinder volume 2 mL

范围 选择 默认值

0.01 ... 6.00 mL/min 最大值 最大值

Filling rate

Input

Enter filling rate. The 最大值 rate depends on the cylinder volume of the buret used. Formula input possible.

Cylinder volume 2 mL

范围 选择 默认值 [Start]

0.01 ... 6.00 mL/min 最大值 最大值

Start Dosino command.

[Stop]

Stop Dosino command.

本文来源：https://www.bwwdw.com/article/azxv.html