7360FX GPON+240E-P开局手册(Ed1.1) 11(1)

7360FX GPON+240E-P开局手册 编制 Prepare:： 姚庆园 审核 Review： 批准 Approve:： 7360FX GPON+240E-P开局手册

1

更改历史 Revision History 版本 Ed 1.0 1.1 2011-06-29 2011-07-10 日期 Date 1 更改次第 Change Times 更改条号 Change Item 姚庆园 姚庆园 编制 Prepare 审核 Review 批准 Approve

7360FX GPON+240E-P开局手册

2

目录Contents

1. 说明：....................................................................................................................................... 4

1.1. 1.2. 1.3. 1.4. 1.5.

组网方案： ................................................................................................................... 4 组网说明： ................................................................................................................... 4 数据及端口配置情况： ............................................................................................... 4 软交换SS 地址： ....................................................................................................... 4 现场版本情况： ........................................................................................................... 4

2. 设备登陆方法： ....................................................................................................................... 5 3. 基本命令： ............................................................................................................................... 5

3.1. 3.2. 3.3. 3.4. 3.5. 3.6. 3.7.

配置硬件 ....................................................................................................................... 5 创建vlan ....................................................................................................................... 6 设置管理地址和管理上联口 ....................................................................................... 7 打开上联端口 ............................................................................................................... 7 创建下挂onu ................................................................................................................ 8 配置ontcard并打开ont上数据上网业务 .................................................................. 9 配置语音业务 ............................................................................................................. 10

4. 其他常用命令 ......................................................................................................................... 11

4.1. 4.2. 4.3. 4.4. 4.5. 4.6.

如有冗余保护,以上命令为NT-A的1口和NT-B的1口做LACP保护配置 ...... 11 检查上联端口状态 ..................................................................................................... 11 显示每块板卡的温度和阈值温度 ............................................................................. 11 配置tl1界面通过telnet方式访问 ............................................................................ 11 检查是否学习到mac地址 ........................................................................................ 12 重启ONT命令，即使OOS也可以使ONT重启 ................................................... 12

7360FX GPON+240E-P开局手册

3

1. 说明：

开局配置文档

1.1. 组网方案：

组网拓扑图：

1.2. 组网说明：

FX7360 OLT 上联华为交换机通连接到IP承载网，实现宽带上网业务和设备管理；语音和管理业务走nt-a的1口上联，上网业务走2口上联

VOIP业务到IP城域网后，在分发到NGN城域网实现；

FX7360通过1:32分光器，下联240E-P实现宽带业务和VOIP业务。

1.3. 数据及端口配置情况：

业务 VLAN 240E-P 管理 756 240E-P数据 C:1001~1026 S:2001 240E-P 语音 903

IP 10.10.32.5 网关 10.10.32.1 NA 10.138.40.2 NA 10.138.40.1 1.4. 软交换SS 地址：

Primary MGC IP：10.2.160.2 Secondary MCG IP: 10.2.161.2

1.5. 现场版本情况：

FX7360的版本: SD_4231.006.fant-f-2048 240E-P版本：3FE53216AOCH16

7360FX GPON+240E-P开局手册

4

2. 设备登陆方法：

TL1命令登录：

串口方式登陆时，在操作终端直接输入”c”键，系统提示信息如下:

Would you like a CLI(C) or a TL1 login(T) or TL1 normal session(N) ? [N]: c

login: isadmin

password:i$@mad-

输入上述初始密码后，会提示输入新密码，选择现场要求使用的密码输入，一般为ans#150

3. 基本命令： 3.1. 配置硬件

创建主控板

configure equipment slot nt-a planned-type fant-f // 创建主控板NTA configure equipment slot nt-b planned-type fant-f //创建NTB

打开主控板主备倒换

configure equipment protection-group 1 admin-status unlock

配置子框类型

configure system security profile admin slot-numbering type-based configure system port-num-in-proto type-based

配置背板和LT板接口速率为10g（现在7360默认都是使用背板10g速率） configure system max-lt-link-speed link-speed ten-gb

保存配置数据 admin save

配置完背板速率以后必须要重启

admin equipment reboot-isam with-self-test

配置1到8槽的LT板

configure equipment slot lt:1/1/1 planned-type fglt-a configure equipment slot lt:1/1/2 planned-type fglt-a configure equipment slot lt:1/1/3 planned-type nglt-a configure equipment slot lt:1/1/4 planned-type nglt-a

7360FX GPON+240E-P开局手册

5

configure equipment slot lt:1/1/5 planned-type nglt-a configure equipment slot lt:1/1/6 planned-type nglt-a configure equipment slot lt:1/1/7 planned-type nglt-a configure equipment slot lt:1/1/8 planned-type nglt-a

打开LT1上的8个pon口

configure pon interface 1/1/1/1 fec-dn disable admin-state up configure pon interface 1/1/1/2 fec-dn disable admin-state up configure pon interface 1/1/1/3 fec-dn disable admin-state up configure pon interface 1/1/1/4 fec-dn disable admin-state up configure pon interface 1/1/1/5 fec-dn disable admin-state up configure pon interface 1/1/1/6 fec-dn disable admin-state up configure pon interface 1/1/1/7 fec-dn disable admin-state up configure pon interface 1/1/1/8 fec-dn disable admin-state up

3.2. 创建vlan

创建名字为11的PQ profile(PQ按照实际需求配置)

configure qos profiles ingress-qos 11 dot1-p0-tc 0 dot1-p1-tc 0 dot1-p2-tc 0 dot1-p3-tc 0 dot1-p4-tc 0 dot1-p5-tc 0 dot1-p6-tc 0 dot1-p7-tc 0

创建管理用的RB vlan756 并应用PQ profile 11

configure vlan id 10 mode residential-bridge in-qos-prof-name name:11

创建数据上网使用的双层vlan 创建2001的SVLAN

configure vlan id stacked:2001:0 mode layer2-terminated in-qos-prof-name name:11

创建2001下的各个CVLAN1001-1026

configure vlan id stacked:2001:1001 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1002 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1003 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1004 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1005 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1006 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1007 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1008 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1009 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1010 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1011 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1012 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1013 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1014 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1015 mode cross-connect in-qos-prof-name name:11

7360FX GPON+240E-P开局手册

6

configure vlan id stacked:2001:1016 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1017 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1018 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1019 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1020 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1021 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1022 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1023 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1024 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1025 mode cross-connect in-qos-prof-name name:11 configure vlan id stacked:2001:1026 mode cross-connect in-qos-prof-name name:11

创建语音单层vlan 903

configure vlan id 903 mode residential-bridge in-qos-prof-name name:11 configure vlan id 903 secure-forwarding configure vlan id 903 broadcast-frames

3.3. 设置管理地址和管理上联口

设置管理地址和管理vlan

configure router static-route 0.0.0.0/0 next-hop 10.33.247.65 //设置管理网关 configure service ies 2 customer 1 create

configure service ies 2 interface \

configure service ies 2 interface \10.33.247.73/27 //设置管理ip和掩码

configure service ies 2 interface \10 create //vlan756设置为管理vlan

configure service ies 2 no shutdown //启用管理配置

configure service vpls 3 customer 1 v-vpls vlan 10 create

configure service vpls 3 sap nt-a:xfp:1:10 create //在nt-a的第一个上联口配置管理vlan(如果用户需求untag上联,则把此命令中756改为0) 如果需要开通带内网管口，并且能和pc互通的话，则执行

configure service vpls 3 sap nt-a:eth:1:0 create （在带外网管口配置管理并设置为untag模式，可以和带内口同时启用）

configure service vpls 3 no shutdown //启用配置

打开网管管理功能

configure system security snmp community public host-address 0.0.0.0/0 context nt privilege read-write

configure system security snmp community ihub host-address 0.0.0.0/0 context ihub privilege read-write

3.4. 打开上联端口

把nt-a和nt-b各4个上联口设置为不使用速率自适应

7360FX GPON+240E-P开局手册

7

configure port nt-a:xfp:1 ethernet no autonegotiate configure port nt-a:xfp:2 ethernet no autonegotiate configure port nt-a:xfp:3 ethernet no autonegotiate configure port nt-a:xfp:4 ethernet no autonegotiate configure port nt-b:xfp:1 ethernet no autonegotiate configure port nt-b:xfp:2 ethernet no autonegotiate configure port nt-b:xfp:3 ethernet no autonegotiate configure port nt-b:xfp:4 ethernet no autonegotiate

configure port nt-a:eth:1 ethernet no autonegotiate （设置带内网管口）

设置上联口速率为强制1000兆(上联口和交换机上的口都必须设为强制千兆速率,否则上联端口起不来)

configure port nt-a:xfp:1 ethernet speed 1000 configure port nt-a:xfp:2 ethernet speed 1000 configure port nt-a:xfp:3 ethernet speed 1000 configure port nt-a:xfp:4 ethernet speed 1000 configure port nt-b:xfp:1 ethernet speed 1000 configure port nt-b:xfp:2 ethernet speed 1000 configure port nt-b:xfp:3 ethernet speed 1000 configure port nt-b:xfp:4 ethernet speed 1000

configure port nt-a:eth:1 ethernet speed 1000 （设置带内口速率）

启用上联口

configure port nt-a:xfp:1 no shutdown configure port nt-a:xfp:2 no shutdown configure port nt-a:xfp:3 no shutdown configure port nt-a:xfp:4 no shutdown configure port nt-b:xfp:1 no shutdown configure port nt-b:xfp:2 no shutdown configure port nt-b:xfp:3 no shutdown configure port nt-b:xfp:4 no shutdown

configure port nt-a:eth:1 no shutdown (启用带内口)

3.5. 创建下挂onu

使用光纤连接onu到olt上，如果正常的设备正常，pon口已经打开，则olt会报告警信息 70/01/04 20:48:50 minor alarm occurred for pon 1/1/1/1 : SERNUM = ALCLF8A326CF, SLID = DEFAULT

创建1框1架1板1口的第一个onu,并且版本设置为3FE53216AOCH16 (SERNUM这一项必须在ALCL后加冒号)

configure equipment ont interface 1/1/1/1/1 sw-ver-pland 3FE53216AOCH16 sernum

7360FX GPON+240E-P开局手册

8

ALCL:F8A326F9 voip-allowed enable enable-aes enable fec-up disable exit all

configure equipment ont interface 1/1/1/1/1 admin-state up

如果onu需要升版,则需要做如下配置 configure equipment ont interface 1/1/1/1/1 sw-dnload-version 3FE53866AOCH21 //下载版本软件至onu,前提是要将最新软件版本放入NT的ONT目录下

configure equipment ont interface 1/1/1/1/1 sw-ver-pland 3FE53866AOCH21 //启用新版本,执行完成之后ONT会自动重启

3.6. 配置ontcard并打开ont上数据上网业务

以240E-P为例，配置onu的card 1为以太模块，并且有4个网口。Card 2为语音模块，带2个语音端口

configure equipment ont slot 1/1/1/1/1/1 planned-card-type 10_100base plndnumdataports 4 plndnumvoiceports 0 admin-state up

configure equipment ont slot 1/1/1/1/1/2 planned-card-type pots plndnumdataports 0 plndnumvoiceports 2 admin-state up

配置card 1的各个网口的uni

configure interface port uni:1/1/1/1/1/1/1 admin-up configure interface port uni:1/1/1/1/1/1/2 admin-up configure interface port uni:1/1/1/1/1/1/3 admin-up configure interface port uni:1/1/1/1/1/1/4 admin-up

设置速率的qos profile 名字为11（举例为100m，可以按照现场实际配置修改速率） configure qos profiles bandwidth 11 excessive-info-rate 100000 committed-info-rate 80000 assured-info-rate 90000 delay-tolerance 8

设置各个网口的速率

configure qos interface 1/1/1/1/1/1/1 upstream-queue 0 bandwidth-profile name:11 configure qos interface 1/1/1/1/1/1/2 upstream-queue 0 bandwidth-profile name:11 configure qos interface 1/1/1/1/1/1/3 upstream-queue 0 bandwidth-profile name:11 configure qos interface 1/1/1/1/1/1/4 upstream-queue 0 bandwidth-profile name:11 创建数据端口的bridge port

configure bridge port 1/1/1/1/1/1/1 configure bridge port 1/1/1/1/1/1/2 configure bridge port 1/1/1/1/1/1/3 configure bridge port 1/1/1/1/1/1/4

7360FX GPON+240E-P开局手册

9

svlan 2001配置到NT-A上联端口2和第一块lt板

configure service vpls 2001 customer 1 v-vpls vlan 2001 create configure service vpls 2001 sap nt-a:xfp:2:2001 create configure service vpls 2001 sap lt:1/1/1:2001 create configure service vpls 2001 no shutdown

数据业务双层vlan应用到onu网口上,并把onu发送过来的包打上CLAN号的tag configure bridge port 1/1/1/1/1/1/1 vlan-id stacked:2001:1001 configure bridge port 1/1/1/1/1/1/1 max-unicast-mac 4 configure bridge port 1/1/1/1/1/1/1 pvid 1001

configure bridge port 1/1/1/1/1/1/2 vlan-id stacked:2001:1002 configure bridge port 1/1/1/1/1/1/2 max-unicast-mac 4 configure bridge port 1/1/1/1/1/1/2 pvid 1002

configure bridge port 1/1/1/1/1/1/3 vlan-id stacked:2001:1003 configure bridge port 1/1/1/1/1/1/3 max-unicast-mac 4 configure bridge port 1/1/1/1/1/1/3 pvid 1003

configure bridge port 1/1/1/1/1/1/4 vlan-id stacked:2001:1004 configure bridge port 1/1/1/1/1/1/4 max-unicast-mac 4 configure bridge port 1/1/1/1/1/1/4 pvid 1004

3.7. 配置语音业务

设置语音card的速率

configure qos interface 1/1/1/1/1/voip upstream-queue 0 priority 8 bandwidth-profile name:11

语音vlan 903配置到NT-A的上联端口1和第一块lt板

configure service vpls 903 customer 1 v-vpls vlan 903 create configure service vpls 903 sap nt-a:xfp:1:903 create configure service vpls 903 sap lt:1/1/1:903 create configure service vpls 903 no shutdown configure service vpls 903 user-user-com

创建语音端口bridge port

configure bridge port 1/1/1/1/1/voip

903vlan应用到语音端口

configure bridge port 1/1/1/1/1/voip vlan-id 903 configure bridge port 1/1/1/1/1/voip pvid 903

配置1框1架1板1pon口的第一个onu语音的ip地址。其中xml文件按照CIG的规则配置，按照现场的具体要求更改

7360FX GPON+240E-P开局手册

10

本文来源：https://www.bwwdw.com/article/a8iv.html