新格林耐特配置命令

更新时间:2024-04-18 07:32:01 阅读量: 综合文库 文档下载

说明:文章内容仅供预览,部分内容可能不全。下载后的文档,内容与下面显示的完全一致。下载之前请确认下面内容是否您想要的,是否完整无缺。

新格林耐特

第一部分:TiNetS2000EI系列配置命令及说明

(红色标识为一些常用命令)

Username(1-32 chars):admin

Password(1-16 chars):****** /登陆交换机,默认密码123456/ TiNet>enable /进入特权模式/ TiNet#configure terminal /进入全局模式/ TiNet(config)#

1. TINET#terminal language /改变语言模式/

例如:TINET#terminal language Chinese /改成中文模式/

2. TiNet#clear startup-config /清除配置,恢复出厂默设置/

3. TiNet#copy running-config startup-config /保存配置命令/

4. TiNet#load ?

application 下载应用程序 configuration 下载配置文件

keyfile 下载SSH密钥文件

whole-bootrom 下载全部的bootrom /设备升级命令/

5. TiNet(config)#ipaddress 192.168.1.5 255.255.255.0 192.168.1.1

/配置交换机IP地址/

6. TiNet(config)show ? / show命令,后可以打问号/

Show ip Show mac Show interface

Show vlan

7. TiNet(config)#vlan 3901 /建立VLAN3901/

TiNet(config-if-vlan)#switchport ethernet 0/1 /把端口1加入该VLAN/ TiNet(config)#ip vlan 3901 /定义管理vlan为3901 TiNet(config)#no ip vlan 1 / 删除默认管理VLAN 1/

8. TiNet(config)#vlan 1001-1512 /批量建立VLAN /

9. TiNet(config-if-vlan)#switchport ethernet 0/2 to ethernet 0/8 ethernet 0/11 ethernet 0/16

/在某一VLAN中或者VLAN段中批量加入端口/

第 1 页 共 8 页

新格林耐特

10. TiNet(config-if-ethernet-0/16)#tag vlan 1001,1112-1512,4000

/端口下批量打tag/

11. T iNet(config-if-ethernet-0/1)#switchport mode trunk

/改变端口模式,为trunk模式/

12. TiNet(config-if-ethernet-0/1)#switchport trunk allowed vlan all

/端口为trunk模式,允许所有VLAN通过/

13. TiNet(config-if-ethernet-0/2)#switchport access vlan 1001

/改变端口PVID/

14. TiNet(config)#port-isolation ethernet ?

STRING<3-4> 端口号为槽端口号<0-2>/端口号<1-24> TiNet(config)#port-isolation ethernet 0/2 to e 0/16

添加端口隔离下行端口成功. /一步隔离,一条命令隔离

除上行口以外所有端口/

15. TiNet(config)#interface range ethernet 0/2 to ethernet 0/16 /批量端口处理命令/

16. TiNet(config-if-range)#bandwidth-control ?

egress 出口带宽控制

ingress 入口带宽控制 /端口限速命令/

17. TiNet(config)#show utilization interface /实时查看端口流量占比/

Link Utilization Averages Thu Jan 1 00:43:20 1970 port link Receive Peak Rx Transmit Peak Tx Status pkts/sec pkts/sec pkts/sec pkts/sec

================================================================== e0/1 down 0 0 0 0 e0/2 down 0 0 0 0 e0/3 down 0 0 0 0 e0/4 down 0 0 0 0 e0/5 down 0 0 0 0 e0/6 down 0 0 0 0 e0/7 down 0 0 0 0 e0/8 down 0 0 0 0 e0/9 down 0 0 0 0 e0/10 down 0 0 0 0 e0/11 down 0 0 0 0 e0/12 down 0 0 0 0 e0/13 down 0 0 0 0 e0/14 down 0 0 0 0 e0/15 down 0 0 0 0

第 2 页 共 8 页

新格林耐特

e0/16 down 0 0 0 0 e1/1 down 0 0 0 0

====spacebar->toggle screen U->page up D->page down CR->exit==== 通过空格键来切换 回车键结束查看

18. TiNet(config)#username change-passwo请输入您的登录密码: ******

请输入用户名(4--15位):admin 请输入新口令(1--15位):******** 输入确认口令(1--15位):********

用户admin密码修改成功。 /修改登陆密码/

第 3 页 共 8 页

新格林耐特

配置案例:

小河区某小区格林耐特设备配置

简要流程

TiNet(config)#ipaddress 119.1.176.185 255.255.255.0 119.1.176.1 /配置ip地址/ Config IP successfully.

TiNet(config)#show ip Switch configuration

ip obtained : MANUAL

ip address : 119.1.176.185 netmask : 255.255.255.0 gateway : 119.1.176.1 ManageVLAN : 1

MAC address : 00:0a:5a:11:ba:b8 /查看交换机ip地址/ TiNet(config)#ex

TiNet#terminal language chinese /更改语言模式为中文/ TiNet(config)#vlan 3901 /建立vlan3901/ TiNet(config-if-vlan)#switchport all /在vlan3901下添加端口/ 添加VLAN端口成功 !

TiNet(config)#ipaddress vlan 3901 /定义交换机管理vlan/ 配置管理VLAN成功! TiNet(config)#show ip

交换机的配置信息

IP 地址获得方式 : MANUAL

IP 地址 : 119.1.176.185 子网掩码 : 255.255.255.0 网关地址 : 119.1.176.1

管理VLAN : 1 3901 /此时管理vlan为1和3901/ MAC 地址 : 00:0a:5a:11:ba:b8

TiNet(config)#no ipaddress vlan 1 /删除交换机默认管理vlan1/ 删除管理VLAN成功!

第 4 页 共 8 页

新格林耐特

TiNet(config)#show ip

交换机的配置信息

IP 地址获得方式 : MANUAL

IP 地址 : 119.1.176.185 子网掩码 : 255.255.255.0 网关地址 : 119.1.176.1 管理VLAN : 3901

MAC 地址 : 00:0a:5a:11:ba:b8 /管理vlan已改为3901/ TiNet(config)#inter range ethernet 0/1 to ethernet 0/16 /批量进入端口1-16 TiNet(config-if-range)#tag vlan 3901 /端口1-16 tag vlan 3901 / TiNet(config-if-range)#ex

TiNet(config)#vlan 1001 /建立vlan 1001/ TiNet(config-if-vlan)#switchport ethernet 0/1 /vlan1001中加入端口1/ 添加VLAN端口成功 !

TiNet(config-if-vlan)#show vlan 1001 显示VLAN信息

VLAN ID : 1001 VLAN status : static VLAN member : e0/1. Static tagged ports : Static untagged Ports : e0/1. Dynamic tagged ports :

TiNet(config)#vlan 1015-1030 /批量建立vlan 1015-1030/ TiNet(config-if-vlan)#switchport ethernet 0/1 ethernet 0/16

/vlan1015-1030加入端口1-16/ 添加VLAN端口成功 !

TiNet(config-if-vlan)#show vlan 1015

显示VLAN信息

VLAN ID : 1015 VLAN status : static

VLAN member : e0/1,e0/16. Static tagged ports :

Static untagged Ports : e0/1,e0/16. Dynamic tagged ports :

TiNet(config)#port-isolation ethernet 0/2 to e 0/16 /端口2-16进行隔离,1

口为上行口,未隔离/

添加端口隔离下行端口成功.

TiNet(config-if-ethernet-0/1)#switchport ? access access 端口

第 5 页 共 8 页

新格林耐特

backup 配置备份端口 mode 端口模式 trunk trunk 端口

TiNet(config-if-ethernet-0/1)#switchport mode trunk

/更改端口1模式为trunk/

TiNet(config-if-ethernet-0/1)#switchport trunk allowed vlan all

/允许所有vlan通过1口/

TiNet(config-if-ethernet-0/1)#switchport trunk native vlan 3901

/更改1口pvid 为3901/

TiNet(config-if-ethernet-0/1)#ex

TiNet(config)#show utilization interface /查看端口实时流量/ Link Utilization Averages Thu Jan 1 00:24:37 1970 port link Receive Peak Rx Transmit Peak Tx Status pkts/sec pkts/sec pkts/sec pkts/sec

================================================================== e0/1 down 0 0 0 0 e0/2 down 0 0 0 0 e0/3 down 0 0 0 0 e0/4 down 0 0 0 0 e0/5 down 0 0 0 0 e0/6 down 0 0 0 0 e0/7 down 0 0 0 0 e0/8 down 0 0 0 0 e0/9 down 0 0 0 0 e0/10 down 0 0 0 0 e0/11 down 0 0 0 0 e0/12 down 0 0 0 0 e0/13 down 0 0 0 0 e0/14 down 0 0 0 0 e0/15 down 0 0 0 0 e0/16 down 0 0 0 0 e1/1 down 0 0 0 0

====spacebar->toggle screen U->page up D->page down CR->exit====

TiNet(config)#username change-password /修改登录密码/ 请输入您的登录密码: ****** 请输入用户名(4--15位):admin 请输入新口令(1--15位):****** 输入确认口令(1--15位):******

/用户admin密码修改成功/

TiNet#copy running-config startup-config /保存配置命令/

第 6 页 共 8 页

新格林耐特

第二部分:交换机实现telnet管理 配置步骤

第一步:配置规划好的交换机ip地址 例:

TiNet(config)#ipaddress 119.1.176.185 255.255.255.0 119.1.176.1 /配置ip地址/ Config IP successfully. TiNet(config)#show ip Switch configuration

ip obtained : MANUAL

ip address : 119.1.176.185 netmask : 255.255.255.0 gateway : 119.1.176.1 ManageVLAN : 1

MAC address : 00:0a:5a:11:ba:b8 /查看交换机ip地址/

第二步:建立规划好的管理vlan,把上行口加入到管理vlan中,然后删除默认的管理vlan 1 例:

TiNet(config)#vlan 3901 /建立vlan3901/ TiNet(config-if-vlan)#switchport e 0/1 /在vlan3901中添加端口1/ 添加VLAN端口成功 !

TiNet(config)#ipaddress vlan 3901 /定义交换机管理vlan/ 配置管理VLAN成功! TiNet(config)#show ip

交换机的配置信息

IP 地址获得方式 : MANUAL

IP 地址 : 119.1.176.185 子网掩码 : 255.255.255.0 网关地址 : 119.1.176.1

管理VLAN : 1 3901 /此时管理vlan为1和3901/ MAC 地址 : 00:0a:5a:11:ba:b8

TiNet(config)#no ipaddress vlan 1 /删除交换机默认管理vlan1/ 删除管理VLAN成功!

第三步:进入上行口,给管理vlan 打标 例:

TiNet(config)#interface ethernet 0/1 /进入到上行口模式/ TiNet(config-if-ethernet-0/1)#tag vlan 3901 /打标/

经过以上三个步骤,如果上层级联交换机配置无误,就可以远程telnet管理交换机。

第 7 页 共 8 页

新格林耐特

第三部分:交换机SNMP网管配置

TiNet(config)#snmp-server community gzgy@))* rw permit

TiNet(config)#snmp-server host 202.98.199.206 version 2c gzgy@))*

TiNet(config)#snmp-server host 202.98.199.209 version 2c gzgy@))*

TiNet(config)#snmp-server host 202.98.199.212 version 2c gzgy@))*

交换机默认开启SNMP代理功能和默认支持SNMPv1/v2/v3,无需其他配置,。 汇聚交换机与楼层交换机同样配置。

第 8 页 共 8 页

本文来源:https://www.bwwdw.com/article/81hp.html

Top