连接器群组测试报告，connector test report - 图文

QA-WI-017-004

QUALIFICATION TEST REPORT 产品测试报告 DESCRIPTION： 产品说明 PART NO.： 料号 DATE： 日期 DOCUMENT NO.： 文件号码 H3.75 CONNECTOR 高度3.75mm连接器 1233-3321152 2012/12/28 QA-2012122804 REV.： A 版本 BY APPROVED 核准 BY CHECKED 审核 WRITTEN 制作

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 2/2 REV 1 INDEX 索引 1. SCOPE 3 适用范围 2. APPLICABLE DOCUMENTS 3 适用的文件 3. TEST CONDITIONS AND SEQUENCE 3 ? 5 测试条件与次序 4. TEST METHOD OF INSPECTION 5 ?10 测试检验方法 5. SUMMARY OF THE QUALIFICATION 11 ? 27 TEST RESULT 测试结果 6. APPENDIX 28 附件

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 3/3 REV 1 1. SCOPE 适用范围 1.1 1.2 TESTED SAMPLES: 85 pcs. 测试样品数: 85个 PURPOSE This qualification test report contains the quality requirements, test procedures and test results of a qualification test program on the part no:101001-510510 目的 这个合格检验报告针对泰强料号: 101001-510510进行测试，测试内容包含合格测验规范、测验程序和测验的结果 2. APPLICABLE DOCUMENTS 适用的文件 2.1 2.2 EIA-RS-364 Test report of FCN: QA-2012122804 3. TEST CONDITIONS AND SEQUENCE 测试条件与次序 3.1 TEST CONDITIONS Unless otherwise specified, tests and examinations were conducted under conditions within the following ranges: Temperature: 20±5℃ Atmospheric Pressure: 650 to 800 millimeters (25.6 to 31.5 inches) of Mercury Relative Humidity: 40% to 70% 测试条件 除非额外规定,检验依下面的范围之内的条件下实施： 温度: 20 ± 5 ℃ 大气压力：650至800毫米( 25.6至31.5英吋) 水银柱高。 相对湿度：40%到70%

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR 3.2 QUALIFICATION TEST SEQUENCE 测试次序 Item 项目 DOCUMENT N0. QA-2012122804 PAGE 4/4 REV 1 DESCRIPTION 叙述 Examination of product外观检验 Contact resistance 接触阻抗 Insulation resistance 绝缘阻抗 Dielectric withstanding Voltage 耐电压 TEMPERATURE RISING 温升 Vibration振动 Mechanical shock机械冲击 Contact retention force保持力 Mating force插入力 Unmating force 拔出力 Durability 耐插拔 Thermal shock 热冲击 Humidity 热湿性测试 Humidity- temperature cycling 温湿度循环 Temperature life 高温寿命 Low temperature 低温寿命 Salt spray 盐水喷雾 H2S Gas 硫化氢测试 Ammonia(NH3)Gas 氨气测试 Solderability 沾锡性 Soldering heat withstanding 耐焊锡性 Lock Strength 锁卡强度 Reverse mating force反向插入力 SEQUENCE 次序 A 1，3 B 1，4 C 1 D 1，4 E F 1，9 2，8 3，6 4，7 G 1，9 2，8 3，6 4，7 H 1，9 2，8 3，6 4，7 I 1，9 2，8 3，6 4，7 J 1，9 2，8 3，6 4，7 K 1，5 2，4 L 1，5 2，4 M 1，5 2，4 N 1，3 O 1，3 P 1 Q 1 METHOD 方法 1 2 3 1，5 2， 4 4-1 4-2 4-3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 2 4-4 4-5 4-6 4-7 4-8 4-9 4-9 4-10 4-11 4-12 4-13 4-14 4-15 4-16 4-17 4-18 4-19 4-20 4-21 4-22 2 3 2 2 3 3 5 5 5 5 5 3 3 3 2 2 2 2

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 5/5 REV 1 4. TEST METHOD OF INSPECTION 测试检验方法 4-1 EXAMINATION OF PRODUCT Visual inspection and dimensional examination in compliance with applicable specifications and documents were performed. The test samples shall be free from defects such as damage, creep, deformation, blister and burrs that are detrimental to the functions and appearances of test samples. 外观检验 目视检查和尺寸的检验依照已实施之规范及文件做其检验内容。测验样品不应有影响功能性及外观不良等缺陷，如损害、潜变、变形、水泡和毛边等问题。 CONTACT RESISTANCE The test was performed in accordance with EIA-364-23. Open circuit voltage is 20 mV maximum and test current is 100 mA maximum level contact resistance requirement is 40 mΩ (resistance of termination wires shall be deducted from the reading) for initial samples, I.e., samples have not been subjected to any environmental test, and is 80 mΩ for environmentally stressed samples.. 接触阻抗 此测试依据EIA-364-23.来执行检测。测试电压是20 mV最大值并且测验电流是 100 mA最大值初始样品最大接触阻抗为40 mΩ (线材的阻抗值应从所得到的电阻值中扣除)样品经过环境的测试最大接触阻抗为80 mΩ。 INSULATION RESISTANCE Insulation resistance was measured between adjacent contacts after applying 500 VDC for 1 minute. The test was performed in accordance with EIA-364-21. Minimum insulation resistance requirement is 100 MΩ for initial samples. 绝缘阻抗 绝缘阻抗为相接连之端子经由500 VDC通过一分钟后，所量测之值。此测试依据EIA-364-21来执行检测。样品未受任何环境测验，最小绝缘体阻抗需求对于初始样品为100 MΩ。 DIELECTRIC WITHSTANDING VOLTAGE A 500 VAC was applied between two adjacent contacts of the test samples for 1 minute. While applying the voltage, the leakage current was monitored and shall be less than 0.5 mA. The test was performed in accordance with EIA-364-20. 耐电压 4-2 4-3 4-4

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 6/6 REV 1 4-5 相接连之端子经由一 500 VAC流电通过一分钟。在通过电压时,漏电电流应小于0.5 mA。此测试依据EIA-364-20.来执行检测。 TEMPERATURE RISING Contact series-wired, apply test current of loaded rating current to the circuit, and measure the temperature rising by probing on soldered area of contacts. After the temperature becomes stabilized deduct ambient temperature from the measured value. 温升 连续接触连线，适用对电路测试装载电流，通过在接触的焊接区域量测所提升温度，4-6 当温度变的稳定以后，从测量的温度数值中扣除环境温度。 VIBRATION The test was performed in accordance with EIA-364-28B. Mated samples were subjected to vibration test per axis. Test duration for each axis was 2 hours (total of 6 hours). The test current was 100 mA for all contacts, which were wired in series and attached to an electrical discontinuity monitor. Throughout the test, electrical discontinuity of 1 microsecond or longer shall not be allowed. 振动 此测试依据EIA-364-28 来执行检测。将公母配合的连接器受每轴心的振动测验。 每一个轴心的测验持续时间是 2 小时 ( 总共6小时) 。针对每一端子通过100 mA的检测电流，且每一端子需接一串接电路至一电子不连续性监视器。经由测试，一微秒或者更长的电不连续性将不被允许。 MECHANICAL SHOCK The test was performed in accordance with EIA-364-27B. Mated samples were subjected to 6 shocks per axis (total of 18 shocks) complied with half-sine waveform which had a 30G peak level and a normal duration of 11 milliseconds. The test current was 100 mA for all contacts, which were wired in series and attached to an electrical discontinuity monitor. Throughout the test, electrical discontinuity of 1 microsecond or longer shall not be allowed 机械冲击 依据EIA-364-27来执行检测。紧配的样品以30g’s、半正旋波、11毫秒以及各轴向经过六次的冲击(总共18次)。针对每一端子通过100 mA的检测电流，且每一端子需接一串接电路至一电子不连续性监视器。经由测试，一微秒或者更长的电不连续性将不被允许。 TERMINAL RETENTION FORCE The contact retention force was the peak force measured while the contact of connector was pulled out from the insulator housing of the connector perpendicularly. Upon completion of the test, the contact retention force shall exceed 0.3kgf. 4-7 4-8

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 7/7 REV 1 4-9 端子保持力 当连接器端子从塑料垂直地被拔出后，端子保持力为量测到的最大值数据。当测验的完成时, 端子保持力量应超过0.3kgf。 MATING&UNMATING FORCE The test was performed in accordance with EIA-364-13. The mating force & unmating force was the peak force measured while the plug and receptacle samples were mated normally. 插入&拔出力 此测试依据EIA-364-13来执行检测。插入力为样品公母端在正常地插入后所量测到的最大值。 4-10 DURABILITY The test was performed in accordance with EIA-364-09. Test samples were subjected to fully mating and unmating for a predetermined number of cycles. （The durability test for 50cycles. Upon completion of the test）, specified electrical and/or mechanical test item(s) shall be performed and results shall pass respective specification. 耐插拔 此测试依据EIA-364-09来执行检测。测验样品在预定的测试次数下，经由完全地插入及拔出（耐插拔次数50次）。当测验的完成时, 规定了电或机械测验项目应被检验，其结果应符合各别的规范。 4-11 THERMAL SHOCK The test was performed in accordance with EIA-364-32B. Mated connectors were subjected to 5 thermal shock cycles. During each cycle temperature was varied from -55±2℃ to +85±2℃ for a duration of 30 minutes at each limit, and the transition time was 5 minutes maximum between extreme temperatures. 热冲击 此测试依据EIA-364-32来执行检测。将公母配合的连接器从温度-55±2 ℃升到85±2 ℃， 升温时间为30分钟内需达到各温度上限值，连续进行5次循环测试。在每次测试循环结束后到新的测试循环开始，其温度的转换时间最大值为5分钟。 4-12 HUMIDITY The test was performed in accordance with EIA-364-31A. Mated connector. Temperature : 60℃ , 90%~95% R.H . Duration 500hours. Upon completion of the test, there shall be no physical damage to the samples and the samples shall pass the requirements of following test item(s) 热湿性测试

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 8/8 REV 1 此测试依据EIA-364-31来执行检测。将公母配合的连接器在温度：60℃ 湿度90%~95%湿度500小时，需符合产品客户图规范，外观无缺陷。 4-13 HUMIDITY-TEMPERATURE CYCLING The test was performed in accordance with EIA-364-31A. Subject specimens to continues 10 cycles of humidity temperature cycling, cyclic test for 24hours. The temperatures were -10℃,25℃,and ℃. Upon completion of the test, samples shall pass the requirement of specific electrical test(s). 温湿度循环 此测试依据EIA-364-31来执行检测。将公母配合的连接器进行温湿度循环试验，设定温度为-10~25~65℃（1个循环24小时）连续10次循环。当测验的完成时，样品应通过电子测试规范需求。 4-14 TEMPERATURE LIFE HIGH Mated samples were exposed to 80±2℃ temperature for 500 hours. Upon completion of the test, there shall be no evidence of physical damage, and samples shall pass the requirement of specific electrical test(s). 高温寿命 将测试样品暴露在80±2℃温度中经过500小时。当测验的完成时, 样品无物理性的损害， 且样品应通过电气性能测验规范的需求。 4-15 TEMPERATURE LIFE COLD Mated samples were exposed to -40±2℃ temperature for 500 hours. Upon completion of the test, there shall be no evidence of physical damage, and samples shall pass the requirement of specific electrical test(s). 耐寒试验 将测试样品暴露在-40±2℃温度中经过500小时。当测验的完成时, 样品无物理性的损害， 且样品应通过电气性能测验规范的需求。 4-16 SALT SPRAY The test was performed in accordance with EIA-364-26. Test sample were subjected to a fine mist of salt solution. The salt solution was made of 5±1% salt and 95% distilled water by weight. After the exposure, the samples were washed or dipped in running water of temperature lower than 37.8℃,and then air dried at 38℃for 1hours. 盐水喷雾 此试验依据EIA-364-26来执行检测。将测验样品置于一适当的盐水溶液薄雾中。盐水溶液以5±1%的盐和95%的蒸馏水制成。测验样品暴露在35℃和5±1%浓度盐水环境中，进行48小时的测试，测试后，以低于37.8℃的水清洗样品在放置于38℃的干燥空气中一小时。

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR 4-17 H2S GAS DOCUMENT N0. QA-2012122804 PAGE 9/9 REV 1 Mated samples were exposed to 40℃ temperature H2S gas 3ppm density in the air for 96hours. Upon completion of the test, there shall be no evidence of physical damage, and samples shall pass the requirement of specific electrical test(s), the samples were washed or dipped in running water of temperature lower than 37.8℃, and then air dried at 38℃ for 1hours. 硫化氢测试 将测试样品暴露在40℃温度及硫化氢密度3ppm空气中经过96小时。当测验完成时，以低于37.8℃的水清洗样品再放置于38℃的干燥空气中1小时，样品无物理性的损害，且样品应通过电气性能测验规范的需求。 4-18 AMMONIA(NH3) GAS Mated samples were exposed to ammonia(NH3) gas density=28% for 40 minute. Upon completion of the test, there shall be no evidence of physical damage, and samples shall pass the requirement of specific electrical thes(s), the samples were washed or dipped in running water of temperature lower than 37.8℃, and then air dried at 38℃for 1 hours. 氨气测试 将测试样品暴露在氨气浓度28%，经过40分钟。当测验完成时，以低于37.8℃的水清洗样品再放置于38℃的干燥空气中1小时，检查样品无物理性的损害，且样品应通过电气性能测验规范的需求。 4-19 CONTACT SOLDER ABILITY Dip solder-tails into the molten solder(held at 230±5℃)up to 0.5mm from the tip of tails for 3±0.5 sec. after test, the requirement:95% immersed area must show no voids, pin holes. 沾锡性 将距离端子焊脚顶端0.5mm处部位浸入温度为230±2℃的锡炉中3±0.5秒。测试完成后，沾锡面积应大于浸入锡炉中整个端子焊脚面积的95%。 4-20 RESISTANCE TO SOLDERING TEMPERATURE Test samples were subjected to the resistance-to-soldering-temperature test with the temperature profile shown in fig. 1. 耐焊锡性 测验样品经耐焊锡性测试依照图1所表示的温度曲线 4-21 LOCK STRENGTH Measure the lock intensity as the connector at the cable side is pulled. 锁卡强度 测量连接器扣锁的强度，测试需由线端完全拔出。（仅测试第一次拔出力）

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 10/10 REV 1 4-22 REVERSE MATING FORCE To mate connector with the mating side being reverse. 反向插入力 将连接器线端反向插入连接器中。 5. THE SUMMARY OF QUALIFICATION TEST RESULTS 5.1GROUP “A” 测试结果-继续 DESCRIPTION REQUIREMENTS RESULTS RATE 说明 需求 结果 结论 1. EXAMINATION OF Meets requirements of product Passed the specified PRODUCT(initial) drawing. No physical damage. requirements. 外观检验(初始) 需符合产品客户图规范，外观无缺通过规定的需求 陷。 2. Temperature rising MIN MAX AVG 30℃ max. 温升 最小 最大 平均 最大30℃. 3. EXAMINATION OF Meets requirements of product PRODUCT drawing. No physical damage. (after lock strength) 需符合产品客户图规范，外观无缺外观检验 陷。 (经温升实验之后) 5. THE SUMMARY OF QUALIFICATION TEST RESULTS – continued 5.2 GROUP ”B” 测试结果-继续 DESCRIPTION 说明 1. EXAMINATION OF PRODUCT (initial) 外观检验 (初始) REQUIREMENTS RESULTS 需求 结果 Meets requirements of product Passed the specified drawing. No physical damage. requirement. 需符合产品客户图规范，外观无缺通过规定的需求 陷。 RATE 结论 PASS 通过

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DESCRIPTION 说明 2. VIBRATION 振动 DOCUMENT N0. QA-2012122804 PAGE 11/11 REV 1 REQUIREMENTS RESULTS RATE 需求 结果 结论 There shall be no loosened parts No loosened parts or or electrical discontinuity greater electrical discontinuity than 1 u second during the test. 无分离的零件或电流断路 Upon completion of the test, samples shall pass the PASS requirements of following test 通过 item(s). 在测试的过程中，无分离的零件或电流断路不超过1微秒。测试完成后，样品需通过随后的测试项目. 3. EXAMINATION OF PRODUCT (after salt spray) 外观检验 (经振动之后) 4. MECGANICAL SHOCK 机械冲击 Meets requirements of product Passed the specified drawing. No physical damage. requirement. 需符合产品客户图规范，外观无缺通过规定的需求 陷。 There shall be no loosened parts or electrical discontinuity greater than 1 u second during the test. Upon completion of the test, samples shall pass the requirements of following test item(s). 在测试的过程中，无分离的零件或电流断路不超过1微秒。测试完成后，样品需通过随后的测试项目. PASS 通过 5. EXAMINATION OF PRODUCT (after salt spray) 外观检验 (经振动及机械冲击之后) Meets requirements of product drawing. No physical damage. 需符合产品客户图规范，外观无缺陷。

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 12/12 REV 1 5. THE SUMMARY OF QUALIFICATION TEST RESULTS - continued 5.3 GROUP ”C” 测试结果-继续 DESCRIPTION 说明 1. EXAMINATION OF PRODUCT (initial) 外观检验 (初始) 2. CONTACT RETENTION FORCE端子保持力 REQUIREMENTS RESULTS 需求 结果 Meets requirements of product drawing. No physical damage. Passed the specified 需符合产品客户图规范，外观无缺requirements. 通过规定的需求 陷。 1.5N(153gf) /pin Min. 每根端子最小1.5牛顿（153公克力） MIN MAX 最小 最大 214 368 Unit: gf 单位: gf AVG 平均 298 RATE 结论 PASS 通过 PASS 通过 5. THE SUMMARY OF QUALIFICATION TEST RESULTS – continued 5.4 GROUP ”D” 测试结果-继续 DESCRIPTION REQUIREMENTS RESULTS RATE 说明 需求 结果 结论 1. EXAMINATION OF Meets requirements of product Passed the specified PASS PRODUCT drawing. No physical damage. requirement. 通过 (initial) 需符合产品客户图规范， 通过规定的需求 外观检验 外观无缺陷。 (初始) 2. MATING FORCE PASS 100N（10.2kgf）(max) Including MATING FORCE: 插入力 MIN MAX AVG 通过 lock 最大值100牛顿（10.2公斤力）包最小 最大 平均 含扣锁 16.17 20.09 18.32 Unit : N 单位 : 牛顿 3. UNMATING FORCE 12.75N(1.3kgf)(min) excluding UNMATING FORCE: PASS lock 拔出力 MIN MAX AVG 通过 最小值12.75牛顿（1.3公斤力）最小 最大 平均 11.07 15.29 13.13 不包含扣锁 Unit : N 单位 : 牛顿

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 13/13 REV 1 DESCRIPTION REQUIREMENTS RESULTS 说明 需求 结果 4. EXAMINATION OF Meets requirements of product Passed the specified PRODUCT drawing. No physical damage. requirement. (after mating& 需符合产品客户图规范，外观无缺通过规定的需求 Unmating force) 陷。 外观检验 (经插入与拔出之后) RATE 结论 PASS 通过 5. THE SUMMARY OF QUALIFICATION TEST RESULTS – continued 5.5 GROUP “E” 测试结果-继续 DESCRIPTION REQUIREMENTS 说明 需求 1. EXAMINATION OF Meets requirements of product PRODUCT drawing. No physical damage. (initial) 需符合产品客户图规范， 外观检验(初始) 外观无缺陷。 2. CONTACT Initial: 40mΩ max. RESISTANCE 初始最大 40毫欧姆。 (Initial) 接触阻抗 （初始） 3. DURABILITY 耐插拔 After 50 cycles of durability test, the samples shall pass the requirements of following test item(s). 在50次的那插拔测试后,样品需通过随后的测试项目。 80mΩ max 最大值80毫欧姆。 RESULTS 结果 Passed the specified requirement. 通过规定的需求 MIN 最小 21.5 MAX 最大 28.8 AVG 平均 24.8 RATE 结论 PASS 通过 PASS 通过 Unit: mΩ 单位: 毫欧姆 See next items. 看下一项次 PASS 通过 4. CONTACT RESISTANCE (After dureability) 接触阻抗 (经耐插拔之后) MIN 最小 24.5 MAX 最大 29.8 AVG 平均 26.5 PASS 通过 Unit: mΩ 单位: 毫欧姆 5. EXAMINATION OF Meets requirements of product Passed the specified PRODUCT drawing. No physical damage. requirement. (after durability) 需符合产品客户图规范，外观无缺通过规定的需求 外观检验 陷。 (经耐插拔之后) PASS 通过

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR 5.6GROUP ”F DOCUMENT N0. QA-2012122804 PAGE 14/14 REV 1 5. THE SUMMARY OF QUALIFICATION TEST RESULTS – continued 测试结果-继续 DESCRIPTION REQUIREMENTS 说明 需求 1. EXAMINATION OF Meets requirements of product PRODUCT(initial) drawing. No physical damage. 外观检验(初始) 需符合产品客户图规范， 外观无缺陷。 2. CONTACT Initial: 40 mΩ max. RESISTANCE (initial) 初始 : 最大值40 毫欧姆 接触阻抗 (初始) RESULTS 结果 Passed the specified requirement. 通过规定的需求 RATE 结论 PASS 通过 MIN MAX AVG 最小 最大 平均 21.9 27.4 24.42 Unit: mΩ 单位: 毫欧姆 3. INSULATION 100 MΩ min Passed the specified RESISTANCE(initial) 最小值100兆欧姆 requirement. 绝缘阻抗(初始) 通过规定的需求 4. DIELECTRIC A 500V AC is applied for 1 minute. Passed the specified WITHSTANDING There shall be no evidence of requirement. VOLTAGE arcing or breakdown. 通过规定的需求 耐电压 通过500伏特交流电源一分钟。不应有电弧或者损害的迹象。 5. THERMAL SHOCK Upon completion of the test, there No physical damage to shall be no physical damage to the the samples. 热冲击 samples and the samples shall pass 样品无物理性的损害。 the requirements of following test item(s). 当测验的完成时,样品无物理性的损害并且样品将通过随后的测验项目需求。 6. INSULATION Passed the specified 50 MΩ min （Final） RESISTANCE requirement. 最小值50 兆欧姆在试验后。 绝缘阻抗 通过规定的需求 (经热冲击后) 7. DIELECTRIC A 250V AC is applied for 1 minute. Passed the specified WITHSTANDING There shall be no evidence of requirement. VOLTAGE arcing or breakdown. 通过规定的需求 耐电压 通过250伏特交流电源一分钟。不(经热冲击后) 应有电弧或者损害的迹象。 PASS 通过 PASS 通过 PASS 通过 PASS 通过 PASS 通过 PASS 通过

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 15/15 REV 1 DESCRIPTION REQUIREMENTS RESULTS RATE 说明 需求 结果 结论 8. CONTACT 80mΩ max MIN MAX AVG RESISTANCE 最大值80毫欧姆。 最小 最大 平均 PASS (After thermal shock) 通过 22.6 27.1 25.1 接触阻抗 Unit: mΩ (经热冲击后) 单位: 毫欧姆 9. EXAMINATION OF Meets requirements of product Passed the specified PASS PRODUCT drawing. No physical damage. requirement. 通过 (After Thermal shock) 需符合产品客户图规范，外观无缺通过规定的需求 外观检验 陷。 (经热冲击之后) 5. THE SUMMARY OF QUALIFICATION TEST RESULTS – continued 5.7 GROUP “G” DESCRIPTION REQUIREMENTS 说明 需求 1. EXAMINATION OF Meets requirements of product PRODUCT(initial) drawing. No physical damage. 外观检验(初始) 需符合产品客户图规范， 外观无缺陷。 2. CONTACT Initial: 40 mΩ max. RESISTANCE (initial) 初始 : 最大值40 毫欧姆 接触阻抗 (初始) RESULTS 结果 Passed the specified requirement. 通过规定的需求 RATE 结论 PASS 通过 MIN MAX AVG 最小 最大 平均 21.9 27.4 24.42 Unit: mΩ 单位: 毫欧姆 3. INSULATION 100 MΩ min Passed the specified RESISTANCE (initial) 最小值100 兆欧姆 requirement. 绝缘阻抗(初始) 通过规定的需求 4. DIELECTRIC A 500V AC is applied for 1 minute. Passed the specified WITHSTANDING There shall be no evidence of requirement. VOLTAGE (initial) arcing or breakdown. 通过规定的需求 耐电压(初始) 通过500伏特交流电源一分钟。不应有电弧或者损害的迹象。 PASS 通过 PASS 通过 PASS 通过

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DESCRIPTION 说明 5. HUMIDITY 热湿性测试 DOCUMENT N0. QA-2012122804 PAGE 16/16 REV 1 REQUIREMENTS RESULTS RATE 需求 结果 结论 Upon completion of the test, there No physical damage to PASS shall be no physical damage to the the samples. 通过 samples and the samples shall pass 样品无物理性的损害。 the requirements of following test item(s) 热湿性测试后，样品无物理性的损害并且样品将通过随后的测验项目要求。 6. INSULATION 50 MΩ min(Final) Passed the specified PASS RESISTANCE(After 最小值50 兆欧姆 requirement. 通过 humidity) 通过规定的需求 绝缘阻抗 (经热湿性测试后) 7. DIELECTRIC A 250V AC is applied for 1 minute. Passed the specified PASS WITHSTANDING There shall be no evidence of requirement. 通过 VOLTAGE arcing or breakdown. 通过规定的需求 (After humidity) 通过250伏特交流电源一分钟。不耐电压 应有电弧或者损害的迹象。 (经热湿性测试后) 8. CONTACT 80mΩ max MIN MAX AVG RESISTANCE 最大值80毫欧姆 最小 最大 平均 PASS (After humidity) 22.6 27.1 25.1 通过 接触阻抗 Unit: mΩ (经热湿性测试后) 单位: 毫欧姆 9. EXAMINATION OF Meets requirements of product Passed the specified PASS PRODUCT drawing. No physical damage. requirement. 通过 (After humidity) 需符合产品客户图规范，外观无缺通过规定的需求 外观检验 陷。 (经热湿性测试后) 5. THE SUMMARY OF QUALIFICATION TEST RESULTS – continued 5.8 GROUP “H” DESCRIPTION REQUIREMENTS 说明 需求 1. EXAMINATION OF Meets requirements of product PRODUCT(initial) drawing. No physical damage. 外观检验(初始) 需符合产品客户图规范， 外观无缺陷。 RESULTS 结果 Passed the specified requirement. 通过规定的需求 RATE 结论 PASS 通过

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 17/17 REV 1 RESULTS 结果 MIN MAX AVG 最小 最大 平均 21.9 27.4 24.42 Unit: mΩ 单位: 毫欧姆 3. INSULATION Passed the specified 100 MΩ min（initial） RESISTANCE(initial) 最小值100 兆欧姆 requirement. 绝缘阻抗(初始) 通过规定的需求 4. DIELECTRIC A 500V AC is applied for 1 minute. Passed the specified WITHSTANDING There shall be no evidence of requirement. VOLTAGE(initial) arcing or breakdown. 通过规定的需求 耐电压(初始) 通过500伏特交流电源一分钟。不应有电弧或者损害的迹象。 5. Upon completion of the test, there No physical damage to HUMIDITY-TEMPERAshall be no physical damage to the the samples. TURE CYCLING samples and the samples shall pass 样品无物理性的损害。 the requirements of following test 温湿度循环 item(s) 温湿度循环测试后，样品无物理性的损害并且样品将通过随后的测验项目要求。 6. INSULATION 50 MΩ min(Final) Passed the specified RESISTANCE requirement. 最小值100 兆欧姆 绝缘阻抗 通过规定的需求 (经温湿度循环后) 7. DIELECTRIC A 250V AC is applied for 1 minute. Passed the specified WITHSTANDING There shall be no evidence of requirement. VOLTAGE arcing or breakdown. 通过规定的需求 耐电压 通过250伏特交流电源一分钟。不(经温湿度循环后) 应有电弧或者损害的迹象。 8. CONTACT 80mΩ max MIN MAX AVG RESISTANCE 最大值80毫欧姆 最小 最大 平均 接触阻抗 22.6 27.1 25.1 Unit: mΩ (经温湿度循环后) 单位: 毫欧姆 9. EXAMINATION OF Meets requirements of product Passed the specified PRODUCT drawing. No physical damage. requirement. 外观检验 需符合产品客户图规范，外观无缺通过规定的需求 (经温湿度循环后) 陷。 DESCRIPTION REQUIREMENTS 说明 需求 2. CONTACT Initial: 40 mΩ max. RESISTANCE (initial) 初始 : 最大值40 毫欧姆 接触阻抗 (初始) RATE 结论 PASS 通过 PASS 通过 PASS 通过 PASS 通过 PASS 通过 PASS 通过 PASS 通过 PASS 通过

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR 5.9 GROUP “I” DOCUMENT N0. QA-2012122804 PAGE 18/18 REV 1 5. THE SUMMARY OF QUALIFICATION TEST RESULTS – continued 测试结果-继续 DESCRIPTION REQUIREMENTS 说明 需求 1. EXAMINATION OF Meets requirements of product PRODUCT drawing. No physical damage. (initial) 需符合产品客户图规范， 外观检验(初始) 外观无缺陷。 2. CONTACT Initial: 40 mΩ max. RESISTANCE (initial) 初始 : 最大值40 毫欧姆 接触阻抗 (初始) RESULTS 结果 Passed the specified requirement. 通过规定的需求 MIN 最小 21.9 MAX 最大 27.4 AVG 平均 24.42 RATE 结论 PASS 通过 PASS 通过 Unit: mΩ 单位: 毫欧姆 3. INSULATION RESISTANCE 绝缘阻抗 4. DIELECTRIC WITHSTANDING VOLTAGE 耐电压 5. TEMPERATURE LIFE 温度寿命 100 MΩ min 最小值100 兆欧姆 Passed the specified requirement. 通过规定的需求 A 500V AC is applied for 1 minute. Passed the specified There shall be no evidence of requirement. arcing or breakdown. 通过规定的需求 通过500伏特交流电源一分钟。不应有电弧或者损害的迹象。 Upon completion of the test, there No physical damage to shall be no physical damage to the the samples. samples and the samples shall pass 样品无物理性的损害。 the requirements of following test item(s) 温度寿命测试后，样品无物理性的损害并且样品将通过随后的测验项目要求。 50 MΩ min(Final) Passed the specified requirement. 最小值100 兆欧姆 通过规定的需求 PASS 通过 PASS 通过 PASS 通过 6. INSULATION RESISTANCE 绝缘阻抗 (经温度寿命测试后) PASS 通过

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DESCRIPTION 说明 7. DIELECTRIC WITHSTANDING VOLTAGE 耐电压 (经温度寿命测试后) 8. CONTACT RESISTANCE 接触阻抗 (经温度寿命测试后) DOCUMENT N0. QA-2012122804 PAGE 19/19 REV 1 REQUIREMENTS RESULTS RATE 需求 结果 结论 A 250V AC is applied for 1 minute. Passed the specified PASS There shall be no evidence of requirement. 通过 arcing or breakdown. 通过规定的需求 通过250伏特交流电源一分钟。不应有电弧或者损害的迹象。 80mΩ max MIN MAX AVG 最大值80毫欧姆 最小 最大 平均 PASS 22.6 27.1 25.1 通过 Unit: mΩ 单位: 毫欧姆 9. EXAMINATION OF Meets requirements of product Passed the specified PASS PRODUCT drawing. No physical damage. requirement. 通过 外观检验 需符合产品客户图规范，外观无缺通过规定的需求 (经温度寿命环测试后) 陷。 5. THE SUMMARY OF QUALIFICATION TEST RESULTS – continued 5.10 GROUP “J” 测试结果-继续 DESCRIPTION REQUIREMENTS 说明 需求 1. EXAMINATION OF Meets requirements of product PRODUCT drawing. No physical damage. (initial) 需符合产品客户图规范， 外观检验(初始) 外观无缺陷。 2. CONTACT Initial: 40 mΩ max. RESISTANCE (initial) 初始 : 最大值40 毫欧姆 接触阻抗 (初始) RESULTS 结果 Passed the specified requirement. 通过规定的需求 MIN MAX 最小 最大 21.9 27.4 Unit: mΩ 单位: 毫欧姆 AVG 平均 24.42 RATE 结论 PASS 通过 PASS 通过

Qualification Test Report

PART NUMBER 1322-5523453 REQUIREMENTS 需求 100 MΩ min 最小值100 兆欧姆 PRODUCT NAME H3.75 CONNECTOR DESCRIPTION 说明 3. INSULATION RESISTANCE 绝缘阻抗 4. DIELECTRIC WITHSTANDING VOLTAGE 耐电压 5. LOW TEMPERATURE 低温测试 DOCUMENT N0. QA-2012122804 PAGE 20/20 REV 1 6. INSULATION RESISTANCE 绝缘阻抗 (经低温寿命测试后) 7. DIELECTRIC WITHSTANDING VOLTAGE 耐电压 (经低温寿命测试后) 8. CONTACT RESISTANCE 接触阻抗 (经低温寿命测试后) RESULTS 结果 Passed the specified requirement. 通过规定的需求 A 500V AC is applied for 1 minute. Passed the specified There shall be no evidence of requirement. arcing or breakdown. 通过规定的需求 通过500伏特交流电源一分钟。不应有电弧或者损害的迹象。 Upon completion of the test, there No physical damage to shall be no physical damage to the the samples. samples and the samples shall pass 样品无物理性的损害。 the requirements of following test item(s) 低温测试后，样品无物理性的损害并且样品将通过随后的测验项目要求。 100 MΩ min Passed the specified requirement. 最小值100 兆欧姆 通过规定的需求 RATE 结论 PASS 通过 PASS 通过 PASS 通过 PASS 通过 A 250V AC is applied for 1 minute. Passed the specified There shall be no evidence of requirement. arcing or breakdown. 通过规定的需求 通过250伏特交流电源一分钟。不应有电弧或者损害的迹象。 80mΩ max MIN MAX AVG 最大值80毫欧姆 最小 最大 平均 22.6 27.1 25.1 Unit: mΩ 单位: 毫欧姆 9. EXAMINATION OF Meets requirements of product Passed the specified PRODUCT drawing. No physical damage. requirement. (After Thermal shock) 需符合产品客户图规范，外观无缺通过规定的需求 外观检验 陷。 (经低温寿命测试后) PASS 通过 PASS 通过 PASS 通过

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 21/21 REV 1 5. THE SUMMARY OF QUALIFICATION TEST RESULTS – continued 5.11 GROUP ”K” 测试结果-继续 DESCRIPTION 说明 1. EXAMINATION OF PRODUCT (initial) 外观检验 (初始) 2. CONTACT RESISTANCE (initial) 接触阻抗 (初始) REQUIREMENTS 需求 Meets requirements of product drawing. No physical damage. 需符合产品客户图规范， 外观无缺陷。 Initial: 40 mΩ max. 初始: 最大值40 毫欧姆 RESULTS 结果 Passed the specified requirement. 通过规定的需求 RATE 结论 PASS 通过 MIN 最小 10.8 MAX 最大 17.2 AVG 平均 13.14 PASS 通过 Unit: mΩ 单位: 毫欧姆 Upon completion of the test, there No evidence of defects on shall be no physical damage to the samples. samples and the samples shall pass 样品无物理性的损害 the requirements of following test item(s) 在盐雾测试结束后，样品无物理性的损害并且样品将通过随后的测验项目要求。 80mΩ max MIN MAX AVG 最大值80毫欧姆 最小 最大 平均 25.2 43.6 37.2 PASS 通过 3. SALT SPRAY 盐水喷雾 4. CONTACT RESISTANCE (After salt spray) 接触阻抗 (经盐水喷雾) PASS 通过 Unit: mΩ 单位: 毫欧姆 PASS 通过 5. EXAMINATION OF Meets requirements of product Passed the specified PRODUCT drawing. No physical damage. requirement. (After salt spray) 需符合产品客户图规范，外观无缺通过规定的需求 外观检验 陷。 (经盐水喷雾)

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 22/22 REV 1 5. THE SUMMARY OF QUALIFICATION TEST RESULTS – continued 5.12 GROUP ”L” 测试结果-继续 DESCRIPTION 说明 1. EXAMINATION OF PRODUCT (initial) 外观检验 (初始) 2. CONTACT RESISTANCE (initial) 接触阻抗 (初始) 3. H2S GAS H2S 气体实验 REQUIREMENTS 需求 Meets requirements of product drawing. No physical damage. 需符合产品客户图规范， 外观无缺陷。 Initial: 40 mΩ max. 初始: 最大值40 毫欧姆 RESULTS 结果 Passed the specified requirement. 通过规定的需求 RATE 结论 PASS 通过 MIN 最小 11.8 MAX 最大 17.6 AVG 平均 13.6 PASS 通过 Unit: mΩ 单位: 毫欧姆 Upon completion of the test, Passed the specified there shall be no physical requirement. damage to the samples and the 通过规定的需求 samples shall pass the requirements of following test items. 在硫化氢气体测试结束后，样品无物理性的损害并且样品将通过随后的测验项目要求。 80mΩ max MIN MAX AVG 最大值80毫欧姆 最小 最大 平均 43.7 46.2 44.9 PASS 通过 4. CONTACT RESISTANCE 接触阻抗 (经H2S 气体实验) PASS 通过 Unit: mΩ 单位: 毫欧姆 PASS 通过 5. EXAMINATION OF Meets requirements of product Passed the specified PRODUCT drawing. No physical damage. requirement. (After H2S GAS) 需符合产品客户图规范，外观无缺通过规定的需求 外观检验 陷。 (经H2S 气体实验)

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 23/23 REV 1 5. THE SUMMARY OF QUALIFICATION TEST RESULTS – continued 5.13 GROUP ”M” 测试结果-继续 DESCRIPTION 说明 1. EXAMINATION OF PRODUCT (initial) 外观检验(初始) 2. CONTACT RESISTANCE (initial) 接触阻抗(初始) 3. NH3 GAS NH3气体实验 REQUIREMENTS 需求 Meets requirements of product drawing. No physical damage. 需符合产品客户图规范， 外观无缺陷。 Initial: 40 mΩ max. 初始: 最大值40 毫欧姆 RESULTS 结果 Passed the specified requirement. 通过规定的需求 MIN MAX AVG 最小 最大 平均 24.4 27.3 25.5 Unit: mΩ 单位: 毫欧姆 Passed the specified requirement. 通过规定的需求 RATE 结论 PASS 通过 PASS 通过 4. CONTACT RESISTANCE (After NH3 GAS) 接触阻抗 (经NH3气体实验) Upon completion of the test, there shall be no physical damage to the samples and the samples shall pass the requirements of following test items. 于实验结束后，受测样品应无外观之损坏并通过随后试验项目需求。 80mΩ max MIN 最大值80毫欧姆 最小 21.4 PASS 通过 MAX 最大 26.0 AVG 平均 23.8 PASS 通过 Unit: mΩ 单位: 毫欧姆 5. EXAMINATION OF Meets requirements of product Passed the specified PRODUCT drawing. No physical damage. requirement. 外观检验 需符合产品客户图规范，外观无缺通过规定的需求 (经NH3气体实验) 陷。 PASS 通过

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 24/24 REV 1 5. THE SUMMARY OF QUALIFICATION TEST RESULTS – continued 5.14 GROUP ”N” 测试结果-继续 DESCRIPTION REQUIREMENTS RESULTS 说明 需求 结果 1. EXAMINATION OF Meets requirements of product Passed the specified PRODUCT(initial) drawing. No physical damage. requirement. 外观检验(初始) 需符合产品客户图规范，外观无缺通过规定的需求 陷。 2 .CONTACT More than 95% of the dipped Passed the specified SOLDERABILITY surface shall be wet with solder. requirement. 沾锡性 端子沾锡面积应大于浸入锡炉中通过规定的需求 整个端子焊脚总面积的95% 3. EXAMINATION OF Meets requirements of product Passed the specified PRODUCT drawing. No physical damage. requirement. (After solderability ) 需符合产品客户图规范，外观无缺通过规定的需求 外观检验 陷。 (经沾锡性) RATE 结论 PASS 通过 PASS 通过 PASS 通过 5. THE SUMMARY OF QUALIFICATION TEST RESULTS – continued 5.15 GROUP ”O” 测试结果-继续 DESCRIPTION 说明 1. EXAMINATION OF PRODUCT (initial) 外观检验 (初始) 2. SOLDERING HEAT WITHSTANDING 耐焊锡性 REQUIREMENTS RESULTS 需求 结果 Meets requirements of product Passed the specified drawing. No physical damage. requirement. 需符合产品客户图规范，外观无缺通过规定的需求 陷。 RATE 结论 PASS 通过 A visual examination shall be made No physical damage to for physical deterioration such as the samples. cracks and damage. 样品无物理性的损害 物理性的破坏如潜变和损害应以目视检查 3. EXAMINATION OF Meets requirements of product Passed the specified PRODUCT drawing. No physical damage. requirement. (initial) 需符合产品客户图规范，外观无缺通过规定的需求 外观检验 陷。 (耐焊锡性后) PASS 通过 PASS 通过

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 25/25 REV 1 5. THE SUMMARY OF QUALIFICATION TEST RESULTS - continued 5.16 GROUP ”P” 测试结果-继续 DESCRIPTION 说明 1. EXAMINATION OF PRODUCT (initial) 外观检验 (初始) 2. LOCK STRENGTH 扣锁强度 REQUIREMENTS RESULTS RATE 需求 结果 结论 Meets requirements of product Passed the specified PASS drawing. No physical damage. requirements. 通过 需符合产品客户图规范，外观无缺通过规定的需求 陷。 Lock strength:49N(4.998kgf) Min. MIN MAX (initial) 最小 最大 扣锁强度：最小 49牛顿力（4.99860.07 62.79 Unit: N 公斤力）（初始） 单位: N AVG 平均 61.37 PASS 通过 5. THE SUMMARY OF QUALIFICATION TEST RESULTS - continued 5.17 GROUP ”Q” 测试结果-继续 DESCRIPTION 说明 1. EXAMINATION OF PRODUCT (initial) 外观检验(初始) 2. REVERSE MATING FORCE 反向插入力 REQUIREMENTS RESULTS RATE 需求 结果 结论 Meets requirements of product Passed the specified PASS drawing. No physical damage. requirements. 通过 需符合产品客户图规范，外观无缺通过规定的需求 陷。 Connector should not be mate with PASS Passed the specified 49N in a horizontal direction 通过 requirement. 连接器无法以反向水平49牛顿力通过规定需求 量插入。

Qualification Test Report

PART NUMBER 1322-5523453 PRODUCT NAME H3.75 CONNECTOR DOCUMENT N0. QA-2012122804 PAGE 26/26 REV 1 6. APPENDIX 附件 Fig.1

本文来源：https://www.bwwdw.com/article/7ujf.html