Altium Designer 16 快捷键 - 图文

PCB Editor Shortcuts PCB编辑快捷键 SHIFT + RSHIFT + ESHIFT + BSHIFT + PAGE UPSHIFT + PAGE DOWNCTRL + PAGE UPCTRL + PAGE DOWNCTRL + ENDALT + ENDALT + INSERTCTRL + GGNLSHIFT + F1Cycle through three routing modes (ignore, avoid or push切换三种布线模式 (忽略, 避开或推挤)obstacle)Toggle electrical grid on/offBuild QueryZoom-in in small incrementsZoom-out in small incrementsZoom-in to 400%Fit document into viewJump to defined relative origin for the workspaceRedraw current layer onlyPaste on current layerPop up Snap Grid dialogPop up Snap Grid menuHide the ratsnest while moving a componentFlip component being moved to other side of board触发电气格点开/关建立查询放大到最小的递增缩小到最小的递增放大400%适合文档内的查看工作台跳转到绝对的原点刷新当前的层在当前层粘贴弹出捕捉格点对话框弹出捕捉格点菜单移动元件时隐藏飞线翻转正在移动的元件到板的另一边Pressed while routing, displays the appropriate interactive显示合适的交互布线快捷键routing shortcut keysTABF2

CTRL + Left-clickCTRL + SPACEBARBACKSPACESHIFT + SO, D, D, O, ENTERO, D, F, O, ENTERO, D (or CTRL + D)LCTRL + H

Pressed while routing, length tuning, component or string

编辑对话框

placement displays appropriate interactive editing dialogDisplay Board Insight and Heads Up display options

显视器选项

Highlight routed net under cursor (repeat in free space to

在光标下高亮布线的网络

clear)

Cycle through connection lines modes during interactive

在交互布线时循环切换走线模式

routing

Remove last track corner during interactive routingToggle single layer mode on/off (or cycle through SingleLayer Modes set in PCB Preferences: Board InsightDisplay)

Set all primitives to display in draft modeSet all primitives to display in final mode

Access Show/Hide page of View Configurations dialogAccess Board Layers And Colors page of ViewConfigurations dialogSelect connected copper

交互布线时清除最后一个转角开关单层模式

设置所有图元草图模式显示设置所有图元以最终模式显示打开View Configuration 对话框板层和颜色页面选中已连接的铜断线

高亮光标所在的已连接网络下一层上一层

在层面中高亮层

CTRL + SHIFT + Left-click &

Break track

hold

SHIFT + CTRL + Left-click+ (numeric keypad)- (numeric keypad)CTRL + Click

Highlight additional routed net under cursorNext layerPrevious layer

Highlights layer content on layer tabs

CTRL + SHIFT + ClickCTRL + ALT + Mouse* (numeric keypad)MALTCTRLCTRL + M

SPACEBAR (in interactiveprocess)

SPACEBAR (duringinteractive routing)

SHIFT + SPACEBAR (ininteractive process)

SHIFT + SPACEBAR (duringinteractive routing)[]ALT ←ALT →Q

Increments highlighting on layer tabsHovers highlight layer on layer tabsNext routing layerDisplay Move sub-menu

Hold to temporarily switch from avoid-obstacle to ignore-obstacle mode

Hold to temporarily disable electrical grid while routingMeasure distance

在层页面中添加高亮

在层页面中高亮显示鼠标接触的元件下一个走线层显示移动子菜单

按下来暂时从避免障碍模式切换到忽略障碍模式走线时按下来暂时禁用电气栅格测量距离

Rotate object anti-clockwise (define rotation step on PCB

逆时针旋转

Editor - General page of Preferences dialog)Toggle start/end mode

Rotate object being moved clockwise

Step through corner modes during interactive routingDecrease mask level for permanent filterIncrease mask level for permanent filter

View previous component for active library documentView next component for active library documentToggle units (metric/imperial)

切换启动/结束模式顺时针旋转被移动的对象交互布线时切换拐角模式降低过滤器的屏蔽水平提高过滤器的屏蔽水平

在活动的库文档中查看上一个元件在活动的库文档中查看下一个元件切换单位(公制/英制)

Ctrl + QT, BT, P

BACKSPACESPACEBAR

SHIFT + SPACEBARSHIFT + R, (comma). (full stop / period)1234Y

Toggle units (metric/imperial) within an open PCB Editordialog

Access 3D Body Manager dialogAccess Preferences dialog

Remove last interactive length tuning segmentNext interactive length tuning wave patternPrevious interactive length tuning tuning patternToggle Routing Mode

Decrease interactive length tuning pattern amplitude byone increment

Increase interactive length tuning pattern amplitude byone increment

Decrease interactive length tuning miter or radiusIncrease interactive length tuning miter or radiusDecrease interactive length tuning pattern gap byincrement

Increase interactive length tuning pattern gap byincrement

Toggle interactive length tuning amplitude direction

切换单位(公制/英制)对话框打开3D Body Manager 对话框打开Preferences 对话框

移除最后依次交互式长度调整线段下一种交互式长度调整曲线上一种交互式长度调整曲线切换走线模式

以一个单元来降低交互式长度调整曲线的振幅以一个单元来增加交互式长度调整曲线的振幅降低交互式长度调整的半径增加交互式长度调整的半径

以一个单元来降低交互式长度调整曲线的间距以一个单元来增加交互式长度调整曲线的间距切换交互式长度调整振荡的方向

Interactive Routing Shortcuts交互式布线快捷键

Shift+F1 (or ~ (tilde))

Display list of shortcuts

显示快捷列表

CTRL+ ClickBACKSPACEESCSHIFT+ ASHIFT+ CSHIFT+ GSHIFT+ OSHIFT+ PSHIFT+ QSHIFT+ RSHIFT+ SSHIFT+ VSHIFT+ W, (comma)SHIFT+ . (comma). (full stop / period)

Auto-complete segments to targetRemove last segmentTerminate current trace

Add accordion sections (interactive length tuning)Toggle auto-completeToggle length tuning gaugeToggle visible routing areaToggle Push modeToggle glossingToggle routing modeSwitch layer for current traceSelect favorite via size

Open Choose Favorite Width dialog.Decrease arc setbackDecrease arc setback 10xIncrease arc setback

自动完成布线到目标删除最后一段终止目前布线交互式长度调整切换自动完成切换长度调整切换可见布线区切换推挤模式切换注释切换布线模式当前布线层开/关选择最喜欢的通孔选择最喜欢的宽度减少弧度减少弧度10X增加弧度

本文来源：https://www.bwwdw.com/article/53pf.html