紧固件中英文对照大全

更新时间：2024-07-01 10:17:01 阅读量：综合文库文档下载

说明：文章内容仅供预览，部分内容可能不全。下载后的文档，内容与下面显示的完全一致。下载之前请确认下面内容是否您想要的，是否完整无缺。

-------------------------------------------------------------------------------- 螺栓

－－方头螺栓 C级 UDC 621.882.6 | GB 8-88 | 代替 GB8-76 Square head bolts-Product grade C

－－沉头方颈螺栓 UDC 621.882.6 | GB 10-88 | 代替 GB10-76 Flat countersunk square neck bolts

－－沉头带榫螺拴 UDC 621.882.6 | GB 11-88 | 代替 GB11-76 Flat countersunk nib bolts

－－半圆头方颈螺栓 UDC 621.882.6 | GB 12-88 | 代替 GB12-76 Cup head square neck bolts

－－半圆头带榫螺栓 UDC 621.882.6 | GB 13-88 | 代替 GB13-76 Cup head nid bolts

－－大半圆头方颈螺栓 C级 ISO 8677:1986 | GB 14-1998 | 代替 GB14-88 Cup head square neck bolts with large head-Product grade C

－－大半圆头带榫螺栓 UDC 621.882.6 | GB 15-88 | 代替 GB15-76 Cup head nib bolts with large head

－－六角头铰制孔用螺栓 UDC 621.882.6 | GB 27-88 | 代替 GB27-76 Hexagon fit bolts-product grade A and B

－－六角头螺杆带孔铰制孔用螺栓 UDC 621.882.6 | GB 28-88 | 代替 GB28-76 Hexagon fit bolts with split pin hole on shank-product grade A and B

－－六角头头部带槽螺栓 A 和 B 级 UDC 621.882.6 | GB 29.1-88 | 代替 GB29-76 Hexagon bolts with slot on head -product A and B

－－十字槽凹穴六角头螺栓 UDC 621.882.6 | GB 29.2-88 | 代替 GB29-76 Cross recessed hexagon bolts with indentation

－－六角头螺杆带孔螺栓 UDC 621.882.6 | GB 31.1-88 | 代替 GB31、23、24-76 Hexagon bolts with split pin hole on shank-product grade A and B

－－六角头螺杆带孔螺栓细杆 B级 UDC 621.882.6 | GB 31.2-88 | 代替 GB31、23、24-76 Hexagon bolts with split pin hole on shank-Reduced shank-product grade B

－－六角头螺杆带孔螺栓细牙 A和B级 UDC 621.882.6 | GB 31.3-88 | 代替 GB31、23、24-76

Hexagon bolts with split pin hole on shank-Fine pitch thread-product grade A and B －－六角头头部带孔螺栓 A 和 B级 UDC 621.882.6 | GB 32.1-88 | 代替 GB32、25、26-76 Hexagon bolts with wire holes on head-product grade A and B

－－六角头头部带孔螺栓细杆 B级 UDC 621.882.6 | GB 32.2-88 | 代替 GB32、25、26-76 Hexagon bolts with wire holes on head-Reduced shank-product grade B

－－六角头头部带孔螺栓细牙 A 和 B 级 UDC 621.882.6 | GB 32.3-88 | 代替 GB32、25、26-76

Hexagon bolts with wire holes on head-Fine pitch thread-product grade A and B －－下方头螺栓 B级 UDC 621.882.6 | GB 35-88 | 代替 GB35-76 Square head bolts with small head-praduct grade B

－－T 形槽用螺栓 UDC 621.882.6 | GB 37-88 | 代替 GB37-76 Bolts for T-Slot

－－加强半圆头方颈螺栓 GB /T794-93 | 代替 GB794-67

Strengthened cup head square neck bolts

－－活节螺栓 UDC 621.882.6 | GB 798-88 | 代替 GB798-76 Eye bolts

－－地脚螺栓 UDC 621.882.6 | GB 799-88 | 代替 GB799-76 Eyelet bolts

－－沉头双榫螺 UDC 621.882.6 | GB 800-88 | 代替 GB800-77 Flat countersunk double nib bolts

－－小圆半头低方颈螺栓 B级 ISO 8678:1988 | GB /T 801-1998 | 代替 GB801-88 Cup head square neck bolts with small head and short neck-product grade B

－－六角头螺栓 C级 ISO 4016:1999 | GB /T 5780-2000 | 代替 GB/T 5780-1986 Hexagon head bolts-product grade C

－－六角头螺栓全螺纹 C级 ISO 4018:1999 | GB /T 5781-2000 | 代替 GB/T 5781-1986 Hexagon head bolts-Full thread-product grade C

－－六角头螺栓 ISO 4014：1999 | GB /T 5782-2000 | 代替 GB/T 5782-1986 Hexagon head bolts

－－六角头螺栓全螺纹 ISO 4017：1999 | GB /T 5783-2000 | 代替 GB/T 5783-1986 Hexagon head bolts-Full thread

－－六角头螺栓-细杆-B级 UDC 621.882.6 | GB 5784-86 | 代替 GB30、21-76 Hexagon head bolts-Reduced shank -Product grade B

－－六角头螺栓细牙 ISO 8765：1999 | GB /T 5785-2000 | 代替 GB/T 5785-1986 Hexagon head bolts with fine pitch thread

－－六角头螺栓细牙全螺纹 ISO 8676：1999 | GB /T 5786-2000 | 代替 GB/T 5786-1986 Hexagon head bolts with fine pitch thread-Full thread

－－六角法兰面螺栓-加大系列-B级 UDC 621.882.6 | GB 5789-86 | Hexagon flange bolts-Heavy series-product grade B

－－六角法兰面螺栓-加大系列-细杆-B级 UDC 621.882.6 | GB 5790-86 | Hexagon flange bolts-Heavy series-product grade B

－－六角法兰面螺栓小系列 ISO 4162：1990 | GB /T 16674-1996 | 代替 GB/T 5787、5788-1986

Hexagon flange bolts-Small series

－－钢网架螺栓球节点用高强度螺栓 GB /T 16939-1997 | High strength bolts for joints of space grid structures 螺柱

－－双头螺柱 bm=1d UDC 621.882 | GB 897-88 | 代替 GB897-76 Double end studs-bm=1d

－－双头螺柱 bm=1.25d UDC 621.882 | GB 898-88 | 代替 GB898-76 Double end studs-bm=1.25d

－－双头螺柱 bm=1.5d UDC 621.882 | GB 899-88 | 代替 GB899-76 Double end studs-bm=1.5d

－－双头螺柱 bm=2d UDC 621.882 | GB 900-88 | 代替 GB900-76 Double end studs--bm=2d

－－等长双头螺柱 B级 UDC 621.882 | GB 901-88 | 代替 GB901-76

Double end studs(clamping type) -Product grade B

－－手工焊用焊接螺柱 GB 902.1-89 | 代替 GB902-76 Weld studs for manual welding

－－机动弧焊用焊接螺柱 GB 902.2-89 | 代替 GB902-76 Weld studs for arc welding

－－储能焊用焊接螺柱 GB 902.3-89 | 代替 GB902-76 Weld studs for capacitor discharge welding

－－等长双头螺柱 C级 UDC 621.882 | GB 953-88 | 代替 GB953-76 Double end studs(clamping type)-product grade C －－螺杆 GB /T 15389-94 | Threaded rods 螺母

－－方螺母 C级 UDC 621.882.3 | GB 39-88 | 代替 GB39-76 Square nuts-product grade C

－－六角螺母 C级 ISO 4034：1999 | GB /T41-2000 | 代替 GB/T 41-1986 Hexagon nuts-product grade C

－－六角厚螺母 ISO 621.882.3 | GB 56-88 | 代替 GB56-76 Hexagon thick nuts

－－蝶形螺母 UDC 621.882.3 | GB 62-88 | 代替 GB62-76 Wing nuts

－－环形螺母 UDC 621.882.3 | GB 63-88 | 代替 GB63-76 Lifting nuts

－－组合式盖形螺母 UDC 621.882.3 | GB 802-88 | 代替 GB802-76 Acorn nuts

－－球面六角螺母 UDC 621.882.3 | GB 804-88 | 代替 GB804-76 Hexagon nuts with raised face

－－扣紧螺母 UDC 621.882.3 | GB 805-88 | 代替 GB805-76 Tight nuts

－－滚花高螺母 UDC 621.882.3 | GB 806-88 | 代替 GB806-76 Knurled nut with collar

－－滚花薄螺母 UDC 621.882.3 | GB 807-88 | 代替 GB807-76 Knurled nuts

－－小六角特扁细牙螺母 UDC 621.882.3 | GB 808-88 | 代替 GB808-76 Small hexagon thin nuts-Fine pitch thread

－－嵌装圆螺母 UDC 621.882.3 | GB 809-88 | 代替 GB809-76 Lnsert round nuts

－－小圆螺母 UDC 621.882.3 | GB 810-88 | 代替 GB810-76 Small round nuts

－－圆螺母 UDC 621.882.3 | GB 812-88 | 代替 GB812-76 Round nuts

－－端面带孔圆螺母 UDC 621.882.3 | GB 815-88 | 代替 GB815-76 Round nuts with drilled holes in one face

－－侧面带孔圆螺母 UDC 621.882.3 | GB 816-88 | 代替 GB816-79 Round nuts with set pin holes in side

－－带槽圆螺母 UDC 621.882.3 | GB 817-88 | 代替 GB817-76 Slotted round nuts

－－1型非金属嵌件六角锁紧螺母 ISO 7040：1997 | GB /T 889.1-2000 | 代替 GB/T 889-1986

Prevailing torque type hexagon nuts(with non-metallic insert),style 1

－－1型非金属嵌件六角锁紧螺母细牙 ISO 10512：1997 | GB /T 889.2-2000 |

Prevailing torque type hexagon nuts(with non-metallic insert),style 1,with fine pitch thread －－盖形螺母 UDC 621.882.3 | GB 923-88 | 代替 GB923-76 Acorn nuts

－－1型六角螺母 ISO 4032：1999 | GB /T 6170-2000 | 代替 GB/T 6170-1986 Hexagon nuts,style 1

－－1型六角螺母细牙 ISO 8673：1999 | GB /T 6171-2000 | 代替 GB/T 6171-1986 Hexagon nuts,style 1,with fine pitch thread

－－六角薄螺母 ISO 4035：1999 | GB /T 6172.1-2000 | 代替 GB/T 6172-1986 Hexagon thin nuts(chamfered)

－－非金属嵌件六角锁紧薄螺母 ISO 10511：1997 | GB /T 6072.2-2000 | Prevailing torque type hexagon thin nuts(with non-metallic insert)

－－六角薄螺母细牙 ISO 8675：1999 | GB /T 6173-2000 | 代替 GB/T 6173-1986 Hexagon thin nuts(chamfered) with fine pitch thread

－－六角薄螺母无倒角 ISO 4036：1999 | GB /T 6174-2000 | 代替 GB/T 6174-1986 Hexagon thin nuts(unchamfered)

－－2型六角螺母 ISO 4033：1999 | GB /T 6175-2000 | 代替 GB/T 6175-1986 Hexagon nuts,style 2

－－2型六角螺母细牙 ISO 8674：1999 | GB /T 6176-2000 | 代替 GB/T 6176-1986 Hexagon nuts,style 2,with fine pitch thread

－－六角法兰面螺母 ISO 4161：1999 | GB /T 6177.1-2000 | 代替 GB/T 6177-1986 Hexagon nuts with flange

－－六角法兰面螺母细牙 ISO 10663：1999 | GB /T 6177.2-2000 | Hexagon nuts with flange-fine pitch thread

－－1型六角开槽螺母-A和B级 UDC 621.882.3 | GB 6178-86 | 代替 GB57~58-76 Hexagon slotted and castle nuts,style 1 -product grades A and B

－－1型六角开槽螺母-C级 UDC 621.882.3 | GB 6179-86 | 代替 GB57~58-76 Hexagon slotted nuts,style 1 -product grade C

－－2型六角开槽螺母-A和B级 UDC 621.882.3 | GB 6180-86 | Hexagon slotted and castle nuts,style 2 -Product grades A and B

－－六角开槽薄螺母-A和B级 UDC 621.882.3 | GB 6181-86 | 代替 GB59~60-76 Hexagon thin slotted nuts-Product grades A and B

－－2型非金属嵌件六角锁紧螺母 ISO 7041：1997 | GB /T 6182-2000 | 代替 GB/T 6182-1986

Prevailing torque type hexagon nuts(with non-metallic insert),style 2

－－非金属嵌件六角法兰面锁紧螺母 ISO 7043：1997 | GB /T 6183.1-2000 | 代替 GB/T 6183-1986

Prevailing torque type hexagon nuts with flange(with non-metallic insert)

－－非金属嵌件六角法兰面锁紧螺母细牙 ISO 12125：1997 | GB /T 6183.2-2000 |

Prevailing torque type hexagon nuts with flange(with non-metallic insert)with fine pitch thread －－1型全金属六角锁紧螺母 ISO 7719：1997 | GB /T 6184-2000 | 代替 GB/T 6184-1986 Prevailing torque type all-metal hexagon nuts,style 1

－－2型全金属六角锁紧螺母 ISO 7042：1997 | GB /T 6185.1-2000 | 代替 GB/T 6185-1986 Prevailing torque type all-metal hexagon nuts,style 2

－－2型全金属六角锁紧螺母细牙 ISO 10513：1997 | GB /T 6185.2-2000 | Prevailing torque type all-metal hexagon nuts,style 2,with fine pitch thread

－－2型全金属六角锁紧螺母 9级 ISO 7720：1997 | GB /T 6186-2000 | 代替 GB/T 6186-1986

Prevailing torque type all-metal hexagon nuts,style 2-Property class 9

－－全金属六角法兰面锁紧螺母 ISO 7044：1997 | GB /T 6187.1-2000 | 代替 GB/T 6187-1986

Prevailing torque type all-metal hexagon nuts with flange

－－全金属六角法兰面锁紧螺母细牙 ISO 12126：1997 | GB /T 6187.2-2000 | Prevailing torque type all-metal hexagon nuts with flange with fine pitch thread

－－1型六角开槽螺母细牙 A和B级 UDC 621.882.3 | GB 9457-88 | 代替 GB57、58-76 Hexagon slotted and castle nuts,style 1-fine pitch thread-product grades A and B －－2型六角开槽螺母细牙 A和B级 UDC 621.882.3 | GB 9458-88 |

Hexagon slotted and castle nuts,style 2--Fine pitch thread -Product grades A and B

－－六角开槽薄螺母细牙 A和B级 UDC 621.882.3 | GB 9459-88 | 代替 GB59、60-76 Hexagon thin slotted nuts--Fine pitch thread -Product grades A and B －－焊接方螺母 GB /T 13680-92 | Square weld nuts

－－焊接六角螺母 GB /T 13681-92 | Hexagon weld nuts

－－平头铆螺母 GB /T 17880.1-1999 | Flat head riveted nuts

－－沉头铆螺母 GB /T 17880.2-1999 | Countersunk head riveted nuts

－－小沉头铆螺母 GB /T 17880.3-1999 | Small countersunk head riveted nuts

－－120°小沉头铆螺母 GB /T 17880.4-1999 | 120°Small countersunk head riveted nuts

－－平头六角铆螺母 GB /T 17880.5-1999 | Flat head hexagon riveted nuts

－－精密机械用六角螺母 ISO 4166：1979 | GB /T 18195-2000 | Hexagon nuts for fine mechanics 螺钉

－－开槽圆柱头螺钉 ISO 1207：1992 | GB /T 65-2000 | 代替 GB/T 65-1985 Slotted cheese head screws

－－开槽盘头螺钉 ISO 1580：1994 | GB /T 67-2000 | 代替 GB/T 67-1985 Slotted pan head screws

－－开槽沉头螺钉 ISO 2009：1994 | GB /T 68-2000 | 代替 GB/T 68-1985 Slotted countersunk flat head screws (common head style)

－－开槽半沉头螺钉 ISO 2010：1994 | GB /T 69-2000 | 代替 GB/T 69-1985 Countersunk slotted raised head screws (common head style)

－－内六角圆柱头螺钉 ISO 4762：1997 | GB /T 70.1-2000 | 代替 GB/T 70-1985 Hexagon socket head cap screws

－－内六角平圆头螺钉 ISO 7380：1997 | GB /T 70.2-2000 | Hexagon socket button head screws

－－内六角沉头螺钉 ISO 10642：1997 | GB /T 70.3-2000 | Hexagon socket countersunk head screws

－－开槽锥端紧定螺钉 UDC 621.882.219 | GB 71-85 | 代替 GB71-76 Slotted set screws with cone point

－－开槽锥端定位螺钉 UDC 621.882.2 | GB 72-88 | 代替 GB72-76 Slotted setscrews with cone point

－－开槽平端紧定螺钉 UDC 621.882.219.4 | GB 73-85 | 代替 GB73-76 Slotted set screws with flat point

－－开槽凹端紧定螺钉 UDC 621.882.219.4.092.6 | GB 74-85 | 代替 GB74-76 Slotted set screws with cup point

－－开槽长圆柱端紧定螺钉 UDC 621.882.219.4.092.5 | GB 75-85 | 代替 GB75-76 Slotted set screws with long dog point

－－内六角平端紧定螺钉 ISO 4026：1993 | GB /T 77-2000 | 代替 GB/T 77-1985 Hexagon socket set screws with flat point

－－内六角锥端紧定螺钉 ISO 4027：1993 | GB /T 78-2000 | 代替 GB/T 78-1985 Hexagon socket set screws with cone point

－－内六角圆柱端紧定螺钉 ISO 4028：1993 | GB /T 79-2000 | 代替 GB/T 79-1985 Hexagon socket set screws with dog point

－－内六角凹端紧定螺钉 ISO 4029：1993 | GB /T 80-2000 | 代替 GB/T 80-1985 Hexagon socket set screws with cup point

－－方头长圆柱球面端紧定螺钉 UDC 621.882.2 | GB 83-88 | 代替 GB83-76 Square set screws with long dog point and rounded end

－－方头凹端紧定螺钉 UDC 621.882.2 | GB 84-88 | 代替 GB84-76 Square set screws with cup point

－－方头长圆柱端紧定螺钉 UDC 621.882.2 | GB 85-88 | 代替 GB85-76 Square set screws with long dog point

－－方头短圆柱锥端紧定螺钉 UDC 621.882.2 | GB 86-88 | 代替 GB86-76 Square set screws with short dog point and cone end

－－十字槽盘头螺钉 ISO 7045：1994 | GB /T 818-2000 | 代替 GB/T 818-1985 Pan head screws with cross recess －－十字槽沉头螺钉第1部分：钢4.8级 ISO 7046-1：1994 | GB /T 819.1-2000 | 代替 GB/T 819-1985

Countersunk flat head screws (common head style)with cross recess-Part 1:Steel of property class 4.8

－－十字槽沉头螺钉第2部分：钢8.8、不锈钢A2-70和有色金属CU2或CU3 ISO 7046-2：1990 | GB /T 819.2-1997 |

Cross recessed countersunk flat head screws (common head style)-Grade A-Part 2:Steel of property class 8.8, stainless and non-ferrous metals

－－十字槽半沉头螺钉 ISO 7047：1994 | GB /T 820-2000 | 代替 GB/T 820-1985 Countersunk raised head screws (common head style) with cross recess －－方头平端紧定螺钉 UDC 621.882.2 | GB 821-88 | 代替 GB821-76 Square set screws with chamfered end

－－十字槽圆柱头螺钉 ISO 7048：1998 | GB /T 822-2000 | 代替 GB/T 822-1988 Cheese head screws with cross recess

－－十字槽小盘头螺钉 UDC 621.882.2 | GB 823-88 | 代替 GB823-76 Cross recessed small pan head screws

－－吊环螺钉 UDC 621.882 | GB 825-88 | 代替 GB825-76 Eyebolts

－－开槽盘头定位螺钉 UDC 621.882.2 | GB 828-88 | 代替 GB828-76 Slotted pan head set setscrews with dog point

－－开槽圆柱端定位螺钉 UDC 621.882.2 | GB 829-88 | 代替 GB829-76 Slotted setscrews with dog point

－－开槽圆柱头轴位螺钉 UDC 621.882.2 | GB 830-88 | 代替 GB830-76 Slotted cheese head screws with shoulder

－－开槽无头轴位螺钉 UDC 621.882.2 | GB 831-88 | 代替 GB831-76 Slotted shoulder screws

－－开槽带孔球面圆柱头螺钉 UDC 621.882.2 | GB 832-88 | 代替 GB832-76 Slotted capstan screws

－－开槽大圆柱头螺钉 UDC 621.882.2 | GB 833-88 | 代替 GB833-76 Slotted large cheese head screws

－－滚花高头螺钉 UDC 621.882.2 | GB 834-88 | 代替 GB834-76 Knurled thumb screws

－－滚花平头螺钉 UDC 621.882.2 | GB 835-88 | 代替 GB835-76 Knurled screws

－－滚花小头螺钉 UDC 621.882.2 | GB 836-88 | 代替 GB836-76 Knurled screws with small head

－－开槽盘头不脱出螺钉 UDC 621.882.2 | GB 837-88 | 代替 GB837-76 Slotted pan head screws with waisted shank

－－六角头不脱出螺钉 UDC 621.882.2 | GB 838-88 | 代替 GB838-76 Hexagon screws with waisted shank

－－滚花头不脱出螺钉 UDC 621.882.2 | GB 839-88 | 代替 GB839-76 Knurled thumb screws with waisted shank

－－塑料滚花头螺钉 UDC 621.882.2 | GB 840-88 | 代替 GB840-79 Plastic diamond knurlhead screws

－－开槽球面圆柱头轴位螺钉 UDC 621.882.2 | GB 946-88 | 代替 GB946-76 Slotted raised head with shoulder

－－开槽球面大圆柱头螺钉 UDC 621.882.2 | GB 947-88 | 代替 GB947-76 Slotted large raised cheese head screws

－－开槽沉头不脱出螺钉 UDC 621.882.2 | GB 948-88 | 代替 GB948-76 Slotted countersunk head screws with waisted shank

－－开槽半沉头不脱出螺钉 UDC 621.882.2 | GB 949-88 | 代替 GB949-76 Slotted raised countersunk head screws with waisted shank

－－内六角花形盘头螺钉 UDC 621.882.2 | GB 2672-86 | 代替 GB2672-81 Hexagon lobular socket pan head screws

－－内六角花形沉头螺钉 UDC 621.882.2 | GB 2673-86 | 代替 GB2673-81 Hexagon lobular socket countersunk head screws

－－内六角花形半沉头螺钉 UDC 621.882.2 | GB 2674-86 | 代替 GB2674-81 Hexagon lobular socket raised countersunk head screws

－－内六角圆柱头轴肩螺钉 UDC 621.882.215.6 | GB 5281-85 | Hexagon socket head shoulder screws

－－内六角花形圆柱头螺钉-4.8级 UDC 621.882.2 | GB 6190-86 | 代替 GB2671-81 Hexagon lobular socket head cap screws-property class 4.8

－－内六角花形圆柱头螺钉-8.8和10.9级 UDC 621.882.2 | GB 6191-86 | 代替 GB2671-81 Hexagon lobular socket head cap screws-property class 8.8 and 10.9 －－精密机械用紧固件十字槽螺钉 GB /T 13806.1-92 | Fasteners for mechanics-Cross recessed screws 垫圈

－－标准型弹簧垫圈 UDC 621.882.4 | GB 93-87 | 代替 GB93-76 Single coil spring lock washers Normal type

－－平垫圈 C级 ISO 7091：2000 | GB /T 95-2002 | 代替 GB/T 95-1985 Plain washers-Product grade C

－－大垫圈 A级 ISO 7093-1：2000 | GB /T 96.1-2002 | 代替 GB/T 96-1985 Plain washers-Large series-Product grade A

－－大垫圈 C级 ISO 7093-2：2000 | GB /T 96.2-2002 | 代替 GB/T 96-1985 Plain washers-Large series-Product grade C

－－平垫圈 A级 ISO 7089：2000 | GB /T 97.1-2002 | 代替 GB/T 97.1-1985 Plain washers-Product grade A

－－平垫圈倒角型 A级 ISO 7090：2000 | GB /T 97.2-2002 | 代替 GB/T 97.2-1985 Plain washers,chamfered-Product grade A

－－销轴用平垫圈 ISO 8738：1986 | GB /T 97.3-2000 | Plain washers for clevis pins

－－平垫圈用于螺钉和垫圈组合件 ISO 10673：1998 | GB /T 97.4-2002 | 代替 GB/T 9074.24、9074.25-1988

Plain washers for screw and washer assemblies

－－平垫圈用于自攻螺钉和垫圈组合件 ISO 10669：1999 | GB /T 97.5-2002 | 代替 GB/T 9074.29、9074.30-1988

Plain washers for tapping screw and washer assemblies

－－小垫圈 A级 ISO 7092：2000 | GB /T 848-2002 | 代替 GB/T 848-1985 Plain washers-small series-Product grade A

－－球面垫圈 UDC 621.882.4 | GB 849-88 | 代替 GB849-76

Washers with ball face

－－锥面垫圈 UDC 621.882.4 | GB 850-88 | 代替 GB850-76 Washers with cone face

－－开口垫圈 UDC 621.882.4 | GB 851-88 | 代替 GB851-76 Washers with split

－－工字钢用方斜垫圈 UDC 621.882.4 | GB 852-88 | 代替 GB852-76 Square taper washers for I section

－－槽钢用方斜垫圈 UDC 621.882.4 | GB 853-88 | 代替 GB853-76 Square taper washers for slot section

－－单耳止动垫圈 UDC 621.882.4 | GB 854-88 | 代替 GB854-76 Tab washers with long tab

－－双耳止动垫圈 UDC 621.882.4 | GB 855-88 | 代替 GB855-76 Tab washers with long tab and wing

－－外舌止动垫圈 UDC 621.882.4 | GB 856-88 | 代替 GB856-76 External tab washers

－－圆螺母用止动垫圈 UDC 621.882.4 | GB 858-88 | 代替 GB858-76 Tab washers for round nut

－－轻型弹簧垫圈 UDC 621.882.4 | GB 859-87 | 代替 GB859-76 Single coil spring lock washers,Light type

－－鞍形弹性垫圈 UDC 621.882.4 | GB 860-87 | 代替 GB860-76 Curved spring washers

－－内齿锁紧垫圈 UDC 621.882.4 | GB 861.1-87 | 代替 GB861-76 Lock washers internal teeth

－－内锯齿锁紧垫圈 UDC 621.882.4 | GB 861.2-87 | Serrated lock washers internal teeth

－－外齿锁紧垫圈 UDC 621.882.4 | GB 862.1-87 | 代替 GB862-76 Lock washers external teeth

－－外锯齿锁紧垫圈 UDC 621.882.4 | GB 862.2-87 | Serrated lock washers external teeth

－－波形弹性垫圈 UDC 621.882.4 | GB 955-87 | 代替 GB955-76 Wave spring washers

－－锥形锁紧垫圈 UDC 621.882.4 | GB 956.1-87 | 代替 GB956-76 Countersunk external toothed lock washers

－－锥形锯齿锁紧垫圈 UDC 621.882.4 | GB 956.2-87 | Countersunk Serrated external toothed lock washers

－－特大垫圈 C级 ISO 7094：2000 | GB /T 5287-2002 | 代替 GB/T 5287-1985 Plain washers-Extra large series-Product grade C －－重型弹簧垫圈 UDC 621.882.4 | GB 7244-87 | Single coil spring lock washers,heavy type

－－鞍形弹簧垫圈 UDC 621.882.4 | GB 7245-87 | Curved Single coil spring lock washers

－－波形弹簧垫圈 UDC 621.882.4 | GB 7246-87 | Wave Single coil spring lock washers

木螺钉

－－开槽圆头木螺钉 UDC 621.882.2 | GB 99-86 | 代替 GB99-76 Slotted round head wood screws

－－开槽沉头木螺钉 UDC 621.882.2 | GB 100-86 | 代替 GB100-76 Slotted countersunk head wood screws

－－开槽半沉头木螺钉 UDC 621.882.2 | GB 101-86 | 代替 GB101-76 Slotted raised countersunk head wood screws

－－六角头木螺钉 UDC 621.882.2 | GB 102-86 | 代替 GB102-76 Hexagon head wood screws

－－十字槽圆头木螺钉 UDC 621.882.2 | GB 950-86 | 代替 GB950-76 Cross recessed round head wood screws

－－十字槽沉头木螺钉 UDC 621.882.2 | GB 951-86 | 代替 GB951-76 Cross recessed countersunk head wood screws

－－十字槽半沉头木螺钉 UDC 621.882.2 | GB 952-86 | 代替 GB952-76 Cross recessed raised head countersunk head wood screws

自攻螺钉

－－十字槽盘头自攻螺钉 UDC 621.882.216.5.082.8 | GB 845-85 | 代替 GB845-76 Cross recessed pan head tapping screws

－－十字槽沉头自攻螺钉 UDC 621.882.216.5.082.8 | GB 846-85 | 代替 GB846-76 Cross recessed countersunk head tapping screws

－－十字槽半沉头自攻螺钉 UDC 621.882.216.5.082.8 | GB 847-85 | 代替 GB847-76 Cross recessed raised countersunk head tapping screws

－－开槽盘头自攻螺钉 UDC 621.882.215.082.8 | GB 5282-85 | Slotted pan head tapping screws

－－开槽沉头自攻螺钉 UDC 621.882.215.082.8 | GB 5283-85 | Slotted countersunkhead tapping screws

－－开槽半沉头自攻螺钉 UDC 621.882.215.082.8 | GB 5284-85 | Slotted raised countersunkhead tapping screws

－－六角头自攻螺钉 UDC 621.882.215.082.8 | GB 5285-85 | Hexagon head tapping screws

－－十字槽盘头自攻锁紧螺钉 UDC 621.882 | GB 6560-86 | Cross recessed pan head thread forming screws

－－十字槽沉头自攻锁紧螺钉 UDC 621.882 | GB 6561-86 | Cross recessed countersunk head thread forming screws

－－十字槽半沉头自攻锁紧螺钉 UDC 621.882 | GB 6562-86 | Cross recessed raised countersunk head thread forming screws －－六角头自攻锁紧螺钉 UDC 621.882 | GB 6563-86 | Hexagon head thread forming screws

－－内六角花形圆柱头自攻锁紧螺钉 UDC 621.882 | GB 6564-86 | Hexagon lobular socket thread forming screws

－－十字槽头凹穴六角头自攻螺钉 UDC 621.882.2 | GB 9456-88 |

Cross recessed hexagon head tapping screws with indentation

－－精密机械用紧固件十字槽自攻螺钉刮削端 GB /T 13806.2-92 | Fasteners for fine mechanics-Cross recessed tapping screws-Scrape point －－墙板自攻螺钉 GB /T 14210-93 | Dry wall screws

－－十字槽盘头自钻自攻螺钉 ISO 15481:1999 | GB /T 15856.1-2002 | 代替 GB/T 15856.1-1995

Cross recessed pan head drilling screws with tapping screw thread

－－十字槽沉头自钻自攻螺钉 ISO 15482:1999 | GB /T 15856.2-2002 | 代替 GB/T 15856.2-1995

Cross recessed countersunk head drilling screws with tapping screw thread

－－十字槽半沉头自钻自攻螺钉 ISO 15483:1999 | GB /T 15856.3-2002 | 代替 GB/T 15856.3-1995

Cross recessed raised countersunk head drilling screws with tapping screw thread －－六角法兰面自钻自攻螺钉 GB /T 15856.4-2002 | 代替 GB/T 15856.4-1995 Hexagon flange drilling screws with tapping screw thread

－－六角凸缘自钻自攻螺钉 ISO 15480:1999 | GB /T 15856.5-2002 | Hexagon washer head drilling screws with tapping screw thread －－六角凸缘自攻螺钉 ISO 7053:1992 | GB /T 16824.1-1997 | Hexzgon head tapping screws with collar

－－六角法兰面自攻螺钉 ISO 10509:1992 | GB /T 16824.2-1997 | Hexagon flange head tapping screws 销

－－开口销 ISO 1234:1997 | GB /T 91-2000 | 代替 GB/T 91-1986 Split pins

－－圆锥销 ISO 2339:1986 | GB /T 117-2000 | 代替 GB/T 117-1996 Taper pins

－－内螺纹圆锥销 ISO 8736:1986 | GB /T 118-2000 | 代替 GB?T 118-1996 Taper pins with internal thread

－－圆柱销不淬硬钢和奥氏体不锈钢 ISO 2338:1997 | GB /T 119.1-2000 | 代替 GB/T 119-1986

Parallel pins,of unhardened steel and austenitic stainless steel

－－圆柱销淬硬钢和马氏体不锈钢 ISO 8734:1997 | GB /T 119.2-2000 | 代替 GB/T 119-1986

Parallel pins,of hardened steel and martensitic stainless steel (Dowel pins)

－－内螺纹圆柱销不淬硬钢和奥氏体不锈钢 ISO 8733:1997 | GB /T 120.1-2000 | 代替 GB/T 120-1986

Parallel pins with internal thread, of unhardened steel and austenitic stainless steel

－－内螺纹圆柱销淬硬钢和马氏体不锈钢 ISO 8735:1997 | GB /T 120.2-2000 | 代替 GB/T 120-1986

Parallel pins with internal thread,of hardened steel and martensitic stainless steel －－开尾圆锥销 UDC 621.886 | GB 877-76 | 代替 GB877-76

Taper pins with split

－－螺纹圆柱销 UDC 621.886 | GB 878-86 | 代替 GB878-76 Parallel pins with external thread

－－弹性圆柱销直槽重型 ISO 8752:1997 | GB /T 879.1-2000 | 代替 GB/T 879-1986 Spring-type straight pins-Slotted, heavy duty

－－弹性圆柱销直槽轻型 ISO 13337:1997 | GB /T 879.2-2000 | Spring-type straight pins-Slotted,light duty

－－弹性圆柱销卷制重型 ISO 8748:1997 | GB /T 879.3-2000 | Spring-type straight pins-Coiled,heavy duty

－－弹性圆柱销卷制标准型 ISO 8750:1997 | GB /T 879.4-2000 | Spring-type straight pins-Coiled,standard duty

－－弹性圆柱销卷制轻型 ISO 8751:1997 | GB /T 879.5-2000 | Spring-type straight pins-Coiled,light duty

－－带孔销 UDC 621.886 | GB 880-86 | 代替 GB880-76 Pins with split pin hole

－－螺尾锥销 ISO 8737:1986 | GB /T 881-2000 | 代替 GB/T 881-1986 Taper pins with external thread

－－销轴 UDC 621.886 | GB 882-86 | 代替 GB882-76 Clevis pins with head

－－槽销平行沟槽 GB /T 13829.1-92 | Crooved pins-Parallel grooved

－－槽销锥销 GB /T 13829.2-92 | Crooved pins-taper grooved

－－槽销圆头沉头 GB /T 13829.3-92 |

Grooved pins-with round head or countersunk head 铆钉

－－平头铆钉 UDC 621.884 | GB 109-86 | 代替 GB109-76 Flat head rivets

－－标牌铆钉 UDC 621.884 | GB 827-86 | 代替 GB827-76 Rivets for name plate

－－半圆头铆钉(粗制) UDC 621.884 | GB 863.1-86 | 代替 GB863-76 Round head rivets-Black

－－小半圆头铆钉(粗制) UDC 621.884 | GB 863.2-86 | Round head rivets with small head-Black

－－平锥头铆钉(粗制) UDC 621.884 | GB 864-86 | 代替 GB864-76 Cone head rivets-Black

－－沉头铆钉(粗制) UDC 621.884 | GB 865-86 | 代替 GB865-86 Countersunk head rivets-Black

－－半沉头铆钉(粗制) UDC 621.884 | GB 866-86 | 代替 GB866-76 Oval countersunk head rivets-Black

－－半圆头铆钉 UDC 621.884 | GB 867-86 | 代替 GB867-76 Round head rivets

－－平锥头铆钉 UDC 621.884 | GB 868-86 | 代替 GB868-76 Cone head rivets

－－沉头铆钉 UDC 621.884 | GB 869-86 | 代替 GB869-76 Countersunk head rivets

－－半沉头铆钉 UDC 621.884 | GB 870-86 | 代替 GB870-76 Oval countersunk head rivets

－－扁圆头铆钉 UDC 621.884 | GB 871-86 | 代替 GB871-76 Flat round head rivets

－－扁平头铆钉 UDC 621.884 | GB 872-86 | 代替 GB872-76 Thin head rivets

－－扁圆头半空心铆钉 UDC 621.884 | GB 873-86 | 代替 GB873-76 Oval head semi-tubular rivets

－－120°沉头半空心铆钉 UDC 621.884 | GB 874-86 | 代替 GB874-76 120 degree countersunk head semi-tubular rivets

－－扁平头半空心铆钉 UDC 621.884 | GB 875-86 | 代替 GB875-76 Thin head semi-tubular rivets

－－空心铆钉 UDC 621.884 | GB 876-86 | 代替 GB876-76 Tubular rivets

－－120°沉头铆钉 UDC 621.884 | GB 954-86 | 代替 GB954-76 120 degree countersunk head rivets

－－管状铆钉 UDC 621.884 | GB 975-86 | 代替 GB975-76 Pipe type rivets

－－大扁圆头铆钉 UDC 621.884 | GB 1011-86 | 代替 GB1011-76 Truss head rivets

－－120°半沉头铆钉 UDC 621.884 | GB 1012-86 | 代替 GB1012-76 120 degree oval countersunk rivets

－－平锥头半空心铆钉 UDC 621.884 | GB 1013-86 | 代替 GB1013-76 Cone head semi-tubler rivets

－－大扁圆头半空心铆钉 UDC 621.884 | GB 1014-86 | 代替 GB1014-76 Truss head semi-tublar rivets

－－沉头半空心铆钉 UDC 621.884 | GB 1015-86 | 代替 GB1015-76 Countersunk head semi-tublar rivets

－－无头铆钉 UDC 621.884 | GB 1016-86 | 代替 GB1016-76 Headless rivets

－－封闭型扁圆头抽芯铆钉 GB 12615-90 |

Mushroom head break mandrel closed end blind rivets －－封闭型沉头抽芯铆钉 GB 12616-90 |

120 deg flush head break mandrel closed end blind rivets －－开口型沉头抽芯铆钉 GB 12617-90 | 120 deg flush head break mandrel blind rivets －－开口型扁圆头抽芯铆钉 GB 12618-90 | Mushroom head break mandrel blind rivets －－扁圆头击芯铆钉 GB /T 15855.1-1995 | Flat round head drive rivets

－－沉头击芯铆钉 GB /T 15855.2-1995 | Countersunk head drive rivets 挡圈

－－锥销锁紧挡圈 UDC 621.885 | GB 883-86 | 代替 GB883-76 Lock rings with cone pin

－－螺钉锁紧挡圈 UDC 621.885 | GB 884-86 | 代替 GB884-76 Lock ring with screw

－－带锁圈的螺钉锁紧挡圈 UDC 621.885 | GB 885-86 | 代替 GB885-76 Lock rings with screw and circlip

－－轴肩挡圈 UDC 621.885 | GB 886-86 | 代替 GB886-76 Rings for shoulder

－－螺钉紧固轴端挡圈 UDC 621.885 | GB 891-86 | 代替 GB891-76 Lock rings at the end of shaft with screw

－－螺栓紧固轴端挡圈 UDC 621.885 | GB 892-86 | 代替 GB892-76 Lock rings at the end of shaft with bolt

－－孔用弹性挡圈-A型 UDC 621.885 | GB 893.1-86 | 代替 GB893-76 Circlips for holes-type A

－－孔用弹性挡圈-B型 UDC 621.885 | GB 893.2-86 | Circlips for hole-type B

－－轴用弹性挡圈-A型 UDC 621.885 | GB 894.1-86 | 代替 GB894-76 Circlips for shaft-type A

－－轴用弹性挡圈-B型 UDC 621.885 | GB 894.2-86 | Circlips for shaft-type B

－－孔用钢丝挡圈 UDC 621.885 | GB 895.1-86 | 代替 GB895-76 Roundwire snap rings for hole

－－轴用钢丝挡圈 UDC 621.885 | GB 895.2-86 | 代替 GB895-76 Roundwire snap rings for shaft

－－开口挡圈 UDC 621.885 | GB 896-86 | 代替 GB896-76 “E”rings

－－钢丝锁圈 UDC 621.885 | GB 921-86 | 代替 GB921-76 Round wire circlips

－－夹紧挡圈 UDC 621.885 | GB 960-86 | 代替 GB960-76 Grip rings

紧固件-组合件和连接副

－－钢结构用高强度大六角头螺栓 GB /T 1228-91 | 代替 GB1228-84 High strength bolts with large hexagon head for steel structures

－－钢结构用高强度大六角头螺母 GB /T 1229-91 | 代替 GB1229-84 High strength large hexagon nuts for steel structures

－－钢结构用高强度垫圈 GB /T 1230-91 | 代替 GB1230-84 High strength plain washers for steel structures

－－钢结构用扭剪型高强度螺栓连接副 GB /T 3632-1995 | 代替 GB3632-83

Sets of torshear type high strength bolt hexagon nut and plain washer for steel structures

－－螺栓或螺钉和平垫圈组合件 ISO 10644：1998 | GB /T 9074.1-2002 | 代替 GB/T 9074.1、9074.14-1988

Bolt or screw and washer assemblies with plain washers

－－十字槽头螺钉和外锯齿锁紧垫圈组合件 UDC 621.882 | GB 9074.2-88 | Cross recessed pan head screw and serrated lock washer external teeth assemblies －－十字槽盘头螺钉和弹簧垫圈组合件 UDC 621.882 | GB 9074.3-88 | Cross recessed pan head screw and single coll spring lock washer assemblies

－－十字槽盘头螺钉、弹簧垫圈和平垫圈组合件 UDC 621.882 | GB 9074.4-88 | Cross recessed pan head screw, single coil spring lock washer assemblies －－十字槽小盘头螺钉和平垫圈组合件 UDC 621.882 | GB 9074.5-88 | Cross recessed small pan head screw and small plain washer assemblies －－十字槽小盘头螺钉和大垫圈组合件 UDC 621.882 | GB 9074.6-88 | Cross recessed small pan head screw and big plain washer assemblies

－－十字槽小盘头螺钉和弹簧垫圈组合件 UDC 621.882 | GB 9074.7-88 | Cross recessed small pan head screw and single coil spring lock washer assemblies

－－十字槽小盘头螺钉、弹簧垫圈和平垫圈组合件 UDC 621.882 | GB 9074.8-88 |

Cross recessed small pan head screw, single coil spring lock washer and plain washer assemblies －－十字槽沉头螺钉和锥形锁紧垫圈组合件 UDC 621.882 | GB 9074.9-88 |

Cross recessed countersunk head screw and countersunk serrated external toothed lock washer assemblies

－－十字槽半沉头螺钉和锥形锁紧垫圈组合件 UDC 621.882 | GB 9074.10-88 |

Cross recessed raised countersunk head screw and countersunk external toothed lock washer assemblies

－－十字槽凹穴六角头螺栓和平垫圈组合件 UDC 621.882 | GB 9074.11-88 | Cross recessed hexagon bolt with indentation and plain washer assemblies

－－十字槽凹穴六角头螺栓和弹簧垫圈组合件 UDC 621.882 | GB 9074.12-88 | Cross recessed hexagon bolt with indetation single coil spring lock washer assemblies

－－十字槽凹穴六角头螺栓、弹簧垫圈和平垫圈组合件 UDC 621.882 | GB 9074.13-88 | Cross recessed hexagon bolt with indetation,single coil lock washer and plain washer assemblies －－六角头螺栓和弹簧垫圈组合件 UDC 621.882 | GB 9074.15-88 | Hexagon head bolt and single coil spring lock washer assemblies

－－六角头螺栓和外锯齿锁紧垫圈组合件 UDC 621.882 | GB 9074.16-88 | Hexagon head bolt and serrated lock washer external teeth assemblies

－－六角头螺栓、弹簧垫圈和平垫圈组合件 UDC 621.882 | GB 9074.17-88 | Hexagon head bolt,single coil spring lock washer and plain washer assemblies

－－自攻螺钉和平垫圈组合件 ISO 10510：1999 | GB /T 9074.18-2002 | 代替 GB/T 9074.18、9074.19、9074、22、9074、23-1988

Tapping screw and washer assemblies with plain washers

－－十字槽凹穴六角头自攻螺钉和平垫圈组合件 UDC 621.882 | GB 9074.20-88 | Cross recessed hexagon head tapping screw with indentation and plain washer assemblies －－十字槽凹穴六角头自攻螺钉和大垫圈组合件 UDC 621.882 | GB 9074.21-88 |

Cross recessed hexagon head tapping sorew with indentation and large plain washer assemblies

－－组合件用弹簧垫圈 UDC 621.882 | GB 9074.26-88 | Single coil spring lock washer for assembly

－－组合件用外锯齿锁紧垫圈 UDC 621.882 | GB 9074.27-88 | Serrated lock washer external teeth for assembly

－－组合件用锥形锁紧垫圈 UDC 621.882 | GB 9074.28-88 | Lountersunk external toothed lock washer for assembly －－腰状杆螺柱连接副型式分类 GB /T 13807.1-92 | Connections with waisted stud-Tape classification －－腰状杆螺柱连接副螺柱 GB /T 13087.2-92 | Connections with waisted stud-Studs

－－腰状杆螺柱连接副螺母、受力套管 GB /T 13087.3-92 | Connections with waisted stud-Nuts,extension sleeves

－－栓接结构用大六角头螺栓螺纹长度按GB/T 3106 C级 8.8和10.9级 ISO 7411：1984 | GB /T 18230.1-2000 |

Hexagon bolts for high-strength structural bolting with large width across flats(thread lengths according to GB/T 3106)-Product grade C-Property classes 8.8 and 10.9

－－栓接结构用大六角头螺栓短螺纹长度 C级 8.8和 10.9级 ISO 7412：1984 | GB /T 18230.2-2000 |

Hexagon bolts for high-strengthstructural bolting with large width across flats(short thread length)-Product grade C-property classes 8.8 and 10.9

－－栓接结构用大六角头螺母 B级 8和10级 ISO 4775：1984 | GB /T 18230.3-2000 | Hexagon nuts for high-strength structural bliting with large width across flats-Product grade B-Property classes 8 and 10

－－栓接结构用1型大六角螺母 B级 10级 ISO 7414：1984 | GB /T 18230.4-2000 |

Hexagon nuts for structural bolting with large width across flats,style 1-Product grade B-Property class 10

－－栓接结构用平垫圈淬火并回火 ISO 7416：1984 | GB /T 18230.5-2000 | Plain washers for high-strength structural bolting hardened and tempered

－－栓接结构用1型大六角螺母浸热镀锌(加大攻丝尺寸) A和B级 5.6和8级 ISO 7413：1984 | GB /T 18230.6-2000 |

Hexagon nuts for structural bolting,style 1,hot-dip galvanized(oversize tapped)-Product grade A and B-Property classes 5.6 and 8

－－栓接结构用2型大六角螺母浸热镀锌(加大攻丝尺寸) A级 9级 ISO 7417:1984 | GB /T 18230.7-2000 |

Hexagon nuts for structural bolting,style 2,hot-dip galvanized(oversize tapped)-Product grade A -Property class 9 焊钉

－－无头焊钉 GB 10432-89 | Headless studs for stud welding

－－电弧螺柱焊用圆柱头焊钉 GB /T 10433-2002 | 代替 GB/T 10433-1989 Cheese head studs for arc stud welding

德国标准和国际标准、中国标准中英文对照表

序号德国标准 Item DIN-Standard

1 DIN1 2 DIN7 3 DIN84 4 DIN85 5 DIN93 6 DIN94 7 DIN95 8 DIN96 9 DIN97 10 DIN125-A 11 DIN125-B 12 DIN126 13 DIN127-A 14 DIN127-B 15 DIN128-A 16 DIN137-A 17 DIN137-B 18 DIN186 19 DIN188 20 DIN258 21 DIN261 22 DIN315AF 23 DIN315DF 24 DIN316AF 25 DIN317DF 26

DIN319

中文品名

Description in Chinese

圆锥销圆柱销开槽圆柱头螺钉

开槽盘头螺钉单耳止动垫圈开口销

开槽半沉头木螺钉开槽半圆头木螺钉开槽沉头木螺钉平垫平垫(带倒角)

平垫重型弹垫标准弹垫鞍形弹垫弹簧止动垫圈波形弹垫 T型方颈螺栓 T型双接头螺栓螺纹圆锥销 T型头螺栓蝶形螺母(美制) 蝶形螺母(德制) 蝶形螺钉(美制) 蝶形螺钉(德制) 圆球型盖型螺母

英文品名

Description in English

Taper pins Parallel pins Slotted cheese head

screws

Slotted pan head

screws Tab washers Split cotter pins Slotted raised csk head

wood screws Slotted round head

wood screws Slotted raised csk head

wood screws Plain washers Mediun washers Plain washers

Spring lock washers tang ends

Spring lock washers square ends Single coil spring lock

washers

Curved spring washers Wave spring washers T-head bolts with square

neck

T-head bolts with double nip

Taper pins with threaded end

T-head bolts Wing nuts amercia form Wing nuts germany form Wing screws amercia form Wing screws germany

form Ball knobs

国际标准 ISO-Standard ISO2339 ISO2338 ISO1207 ISO1580 ISO1234

ISO7089 ISO7090 ISO7091

ISO8737

中国标准 GB-Standard GB117 GB119-86 GB65-85 GB67-85 GB854 GB91 GB101 GB99 GB100 GB97.1-85 GB97.2-85

GB7244 GB93-87 GB7245-87 GB955 GB37-88

GB62-88

27 DIN404 28 DIN417 29 DIN427 30 DIN431 31 DIN432 32 DIN433 33 DIN434 34 DIN435 35 DIN436 36 DIN438 37 DIN439 38 DIN439 39 DIN440 40 DIN443 41 DIN444 42 DIN462 43 DIN463 44 DIN464 45 DIN465 46 DIN466 47 DIN467 48 DIN470 49 DIN471 50 DIN472 51 DIN478 52 DIN479 53

DIN480

开槽带孔球面圆柱头螺

钉

开槽长圆柱端紧定螺钉开槽平端紧定螺钉(半

牙)

小六角特薄细牙螺母

外舌止动垫圈小垫圈(用于圆柱头螺

钉)

方斜垫圈(U型)

方斜垫圈(I型) 方垫圈

开槽凹端紧定螺钉六角薄螺母细牙六角薄螺母木螺钉专用垫圈

密封帽活节螺栓B型内舌止动垫圈双耳止动垫圈滚花高头螺钉开槽滚花高头螺钉滚花高螺母滚花薄螺母锁紧垫圈轴用弹性挡圈孔用弹性档圈方头带垫螺栓方头圆柱底端螺栓方头带垫半圆底端螺栓

Slotted capstan screws Slotted set srews with full

dog point

Slotted set srews with chamfered end Pipe nuts with thread External tap

Washers for cheese head

screws

Square taper washers for

U-section

Square taper washers for

I-section Square washers

Slotted set with cup

point

Hexagon thin nuts Hexagon thin nuts Rounds washers for wood

constructions

Sealing caps, push

–in type Eye bolts form B Internal tab washers Washers with two taps Knurled thumb screws

with collar

Slotted knurled thumb screws with collar Knurled thumb nuts with

collar

Knurled thumb thin

nuts

Sealing washers Retaining rings for shafts(external),circlips

Retaining rings for bores(internal), circlips Square head bolts with

collar

Square head bolts with half dog point Square head bolts with

ISO7435 ISO2342 ISO7092

ISO7436 ISO4035 ISO8675 ISO7094

GB832-88 GB75-85 GB73-85 GB808-88 GB856-88 GB848-95 GB852-88 GB852-88 GB74-85 GB6172-86 GB6173-86

GB798-88

GB855-88 GB834-88

GB806-88 GB807-88

GB894.1-86 GB893.1-86

collar, half dog point and

rounded end 54 DIN508 55 DIN525 56 DIN529 57 DIN546 58 DIN547 59 DIN551 60 DIN553 61 DIN555 62 DIN557 63 DIN558 64 DIN561 65 DIN562 66 DIN571 67 DIN580 68 DIN582 69 DIN601 70

DIN603

71 DIN604 72 DIN605 73 DIN607 74 DIN608 75 DIN609 76 DIN610 77 DIN653 78 DIN660 79 DIN661 80

DIN662

T型槽螺母

单头螺柱

地脚螺栓

带槽圆螺母

端面带孔圆螺母

开槽平端紧定螺钉

开槽锥端紧定螺钉

六角螺母

方螺母－C

六角头螺钉

六角头圆柱端紧定螺钉

薄型方螺母—B

六角头木螺钉

吊环螺钉

吊环螺母

六角头螺栓

大半圆头方颈螺栓（马车螺栓)

沉头带插销马车螺栓

沉头长方颈马车螺栓

半圆头带插销马车螺栓沉头短方颈马车螺栓

六角头精配螺栓(长螺

纹)

六角头精配螺栓(短螺

纹)

滚花平头螺钉

半圆头铆钉

沉头铆钉

半沉头铆钉

T-solt nuts Single end studs Masonry bolts Slotted round nuts Round nuts with drilled holes in one face Slotted sit screws with flat point

Slotted set screws with cone point Hexagon nuts Square nuts Hexagon screws Hexagon set screws with full dog point Square nuts without bevel(pressed nuts) Hexagon head wood screws (coach screws) Lifting eye bolts Lifting eye nuts Hexagon bolts Mushroom head square

neck bolt (carriage bolts)

Falt countersunk nib bolts

Falt countersunk long square neck bolts

Cup head nib bolts

Falt countersunk short square neck bolts Hexagon fitted bolts, long thead Hexagon fitted bolts, short thead Knurled thumb screws thin type Round head rivets Contersunk head rivets Raised contersunk head rivets

ISO299

ISO4776 ISO7434 ISO4034

ISO4018

ISO3266

ISO4016 ISO8677

ISO1051 ISO1051 ISO1051

GB799-88 GB817-76 GB815-88 GB73-85 GB71-85 GB39-88

GB102-86 GB825-76

GB14-88

GB835-88 GB867-86 GB869-86

81 DIN674 82 DIN703 83 DIN705 84 DIN741 85 DIN787 86 DIN835 87 DIN906 88 DIN908 89 DIN909 90 DIN910 91 DIN911 92 DIN912 93 DIN913 94 DIN914 95 DIN915 96 DIN916 97 DIN917 98 DIN920 99 DIN921 100 DIN923 101 DIN927 102 DIN928 103 DIN929 104 DIN931 105 DIN933 106 DIN934 107 DIN934 108 DIN935 109

DIN936

大扁头铆钉重型侧面带孔圆螺母侧面带孔圆螺母卡头 T型槽螺钉

双头螺柱(牙长＝2D) 内六角锥型闭锁螺钉内六角直型闭锁螺钉外六角锥型闭锁螺钉外六角直型闭锁螺钉内六角扳手内六角圆柱头螺钉内六角平端紧定螺钉内六角尖端紧定螺钉内六角凹端紧定螺钉薄型盲螺母开槽小圆柱头螺钉开槽大圆柱头螺钉开槽圆柱头轴肩螺钉开槽无头轴肩螺钉焊接方螺母焊接六角螺母六角头螺栓(半牙) 六角头螺栓(全牙) 六角头螺母(1型) 细牙六角头螺母(1型)

开槽六角螺母

六角头薄螺母 Mushroom head rivets Adjusting rings,heavy range(shafting collars) Adjusting rings,light range(shafting collars) Wire rope clips T-slot screws Studs-metal (end=2d) Hexagon socket pipe plugs ,conical threed Hexagon socket screw plugs , cyl. Thread Hexagon head pipe plugs, conical thread Hexagon head pipe plugs , cyl . threed Socket wrendches Hexagon socket cap

screws

Hexagon socket set screws

with flat point

Hexagon socket set screws

with cone point

Hexagon socket set screws

with dog point

Hexagon socket set screws

wit h cup point Hexagon cap nuts Slotted short cheese

head screws Slotted large cheese

head screws Slotted pan head screws with shoulder Slotted shoulder screws Square weld nuts Hexagon weld nuts Hexagon head screws Hexagon head screws Hexagon full nuts Hexagon full nuts Hexagon slotted and castle nuts Hexagon thin nuts

ISO1051

ISO299

ISO2936 ISO4762 ISO4026 ISO4027 ISO4028 ISO4029

ISO4014 ISO4017 ISO4032 ISO8673 ISO7035 ISO4035

GB816-88

GB900-88

GB70-85 GB77-85 GB78-85 GB79-85 GB80-85

GB838-88 GB830-88

GB/T13680-92 GB/T13681-92 GB5782-86 GB5783-86 GB6170-86 GB6171-86 GB6178-86 GB6172.1-86

内六角圆柱端紧定螺钉

110 DIN937 111 DIN938 112 DIN939 113 DIN940 114 DIN960 115 DIN961 116 DIN962 117 DIN963 118

DIN964

119 DIN965 120

DIN966

121 DIN970 122 DIN971 123 DIN972 124 DIN975 125 DIN976 126 DIN979 127

DIN980

128 DIN981 129 DIN982

130 DIN985

六角头开槽薄螺母

双头螺距(牙长＝1D)

双头螺距(牙长＝1.25D)

双头螺距(牙长＝1.5D)

六角头细牙螺栓(半牙) 六角头细牙螺栓(全牙)

头部穿孔六角头螺栓

开槽沉头螺钉

开槽半沉头螺钉

十字槽沉头螺钉

十字槽半沉头螺钉

六角头螺母

细牙六角头螺母(2型)

牙条(全螺纹)

螺纹销

六角头开槽薄螺母(2型) 全金属六角锁紧螺母 (1型)

圆螺母

六角头尼龙锁紧螺母

六角头薄型尼龙锁紧螺

母

Hexagon thin slotted and

castle nuts Studs metal (end=1d) Studs metal (end=1.25d)

Studs metal (end=1.5d) Hexagon head bolts,

metric fine pitch thread Hexagon head bolts, metric fine pitch thread Additional shapes and versions for bolts Slottded countersund head screws Slottded raised countersunk oval head

screws

Cross recessed countersunk heads crews Cross recessed raised countersunk heads

crews Hexagon nuts type-1 Hexagon nuts type-2 Hexagon nuts with fine thread

Threaded rods (studdings)

Threaded pins (stud bolts)

Hexagon thin slotted and

castle nuts

Prevailing torque type

hexagon nuts, all metall nuts Locknuts Prevailing torque type hexagon nuts, heavy type with nylon

insert

Prevailing torque type hexagon nuts, heavy type with nylon

insert 21

ISO7038

ISO8765 ISO8676

ISO 2009 ISO 2010

ISO7046 ISO7047

ISO8674

ISO7199

ISO2982 ISO7040 ISO10511 GB6181-86 GB897-88 GB898-88

GB5785-86 GB5786-86

GB68-85 GB69-85

GB819-85 GB820-85

GB6176-86 GB15389-94

GB6184-86

GB812-88 GB889.1-86

GB6172.2-86

131 DIN986 132 DIN988 133 DIN1052 134 DIN1151 135 DIN1440 136 DIN1441 137 DIN1444 138 DIN1471 139 DIN1472 140 DIN1473 141 DIN1474 142 DIN1475 143 DIN1476 144 DIN1477 145 DIN1479 146 DIN1480 147 DIN1481 148 DIN1587 149 DIN1804 150 DIN1816 151 DIN2093 152 DIN3017 153 DIN3404 154 DIN3567 155 DIN3570 156

DIN6319

六角盖型尼龙锁紧螺母

配合垫片木材连接用垫片沉头钢钉

销钉专用垫片A型销钉专用垫片带头销钉圆锥型槽销圆锥型槽销(半槽) 平行槽销(带倒角) 前端凹槽槽销中部凹槽槽销圆头槽销沉头槽销六角螺母棒花篮螺栓弹性圆柱销组合式盖型螺母开槽圆螺母(配合沟头扳

手)

圆螺母(带插销孔) 盘型弹簧垫圈

喉箍

润滑油嘴(旋扭头)

管夹 U型螺栓球面垫圈

Prevailing torque typedomed capnuts with

nylon insert Shim rings Washers for timber

connectors